User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
One Push Auto Iris F
When the camera recorder is in the Manual Iris
mode, press the [IRIS] button on the lens to adjust
the iris according to the brightness of the subject.
Memo :
0
“One Push Iris” can also be assigned to other
user buttons.
(A P42 [Assignment of Functions to User
Buttons] )
Push Auto Iris
When the camera recorder is in the Manual Iris
mode, press and hold the [IRIS] button on the lens
to change to the Auto Iris mode temporarily. The
iris will be automatically adjusted according to the
brightness of the subject.
Memo :
0
“One Push Iris” can also be assigned to other
user buttons.
(A P42 [Assignment of Functions to User
Buttons] )
About the Iris F-number
Blurry effects due to “small aperture diffraction”
may occur when the diameter of the iris becomes
too small. When this phenomenon occurs, the F-
number on the screen turns gray to warn you that
the diffraction F-number of the iris has been
exceeded.
You are recommended to make appropriate use of
ND filters to prevent the F-number from turning
gray.
Setting the Gain
This function electrically boosts the light sensitivity
when there is insufficient illumination on the object.
You can set the gain of the video amplifier
according to the brightness of the object. Select the
setting mode according to your shooting
conditions.
.
Manual Gain Mode (Manual Gain
Switching)
0
Select the gain level of the video amplifier using
the [GAIN L/M/H] selection switch on the
camera recorder.
0
The a icon on the screen disappears.
0
The default positions of the switch are as
follows.
[L] : 0dB
[M] : 6dB
[H] : 12dB
Memo :
0
You can change the gain value of each position
in the menu. Increasing the sensitivity causes
the screen to appear grainier.
0
The camera recorder switches to the Auto Gain
mode when the gain value is set to “ALC”.
(A P109 [GAIN L/GAIN M/GAIN H] )
Automatic Gain Mode (Automatic Gain
Adjustment)
1
Set the [FULL AUTO] switch to “ON”.
0
The camera recorder switches to the Auto
Gain Adjustment mode (fixed at “ALC”), and
the gain of the video amplifier is
automatically set according to the brightness
of the subject.
In this case, the [GAIN L/M/H] selection
switch on the camera recorder is disabled.
0
The a icon appears on the screen.
Memo :
0
The upper limit of the gain setting value during
ALC operation can be set in [Main Menu] B
[Camera Function] B [ALC Limit].
(
A P109 [ ALC Limit ] )
0
When [Camera Function] B [FULL AUTO] B
[Gain] is set to “SW Set”, the gain value can be
altered using the [GAIN L/M/H] selection switch
even when the [FULL AUTO] switch on the
camera body is set to “ON”.
(A P113 [ Gain ] )
0
You can switch to the Auto Gain mode by setting
the items in [Camera Function] B [GAIN L],
[GAIN M], and [GAIN H] to “ALC”.
(A P109 [GAIN L/GAIN M/GAIN H] )
Adjusting the Iris
59
Shooting