User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
P2P Connection
You can access the web function of this camera
recorder from devices such as a smartphone,
tablet terminal, or PC.
1
[Wireless LAN] appears on the [Wizard]
screen.
.
Back Next
Wireless LAN
Available Adapter
2
Press the I button to display the [Select
Connection Type] screen.
Select “P2P”.
Follow the screen instructions to complete
setting.
Perform setting for the following.
0
Mode of connection
0
Method of setting
* SSID and Passphrase in cases other than
WPS
.
2
Back Next
Connect with Access Point
P2P
Select Connection Type
Memo :
0
When “WPS” is selected in the [Select Setup
Type] screen, the following steps 3 and 4 are not
required.
3
Set the camera recorder to the Camera
mode, and display the [Network] (status)
screen.
0
Press the [STATUS] button on the camera
recorder to display the status screen.
Press the cross-shaped button (HI) to
display the [Network] screen.
0
Check to ensure that the SSID and
Passphrase that you have set in the wizard
are displayed.
.
SSID
Live Streaming
MAC Address
IP Address
Passphrase
Security Type
Ty p e
Network
4
Select SSID from the list of access points
(smartphone, tablet terminal, PC, etc.), and
enter Passphrase.
0
Display a list of the access points in the
wireless connection settings of the
smartphone, tablet terminal or PC, and
select “HM890--*****” or “HM850--*****”.
(***** are numbers that vary with the device
used.)
0
After the password confirmation screen
appears, enter the [Passphrase] displayed
on the [Network] screen.
.
5
Setting is complete.
After setting is complete, you can access the
camera recorder via a web browser.
(A P182 [Connecting from a Web Browser] )
176
Preparing Network Connection
Connecting to the Network