User manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Memo :
0
The battery mark that appears before the “Time”,
“Capacity%” or “Voltage” value changes
according to the remaining battery power.
I
: Battery which the capacity could not be
acquired
4
: Below 13%
D
: 13% or higher
C
: 30% or higher
B
: 60% or higher
F
: Battery communication error
J
: Calibration required
0
When the remaining battery power is low, “RES”
instead of the value is displayed.
Replace the battery as soon as possible.
0
The remaining battery power and remaining
time are intended as reference values for the
shooting duration.
0
The remaining battery level may not be
displayed depending on the type of battery
connected.
Date/Time
For specifying whether to display the date and time
in the display on the LCD monitor and viewfinder
screen.
[Setting Values: ROn, Off]
Date Style
For setting the date display sequence for display
on the LCD monitor and viewfinder screen as well
as for time stamp recording.
Display examples of the setting values are as
follows.
0
DMY2: 30 Jun 2014
0
DMY1:30-06-2014
0
MDY2: Jun 30, 2014
0
MDY1:06-30-2014
0
YMD:2014-06-30
[Setting Values: DMY2, DMY1, MDY1, MDY2,
YMD]
(Default values: MDY2 (U model), DMY1 (E
model))
Time Style
For setting the time display for display on the LCD
monitor and viewfinder screen as well as for time
stamp recording.
[Setting Values: 24hour, 12hour]
(Default values: 12hour (U model), 24hour (E
model))
Shutter
For setting the shutter display to be displayed on
the LCD monitor and viewfinder screen.
0
DEG:
Displays the shutter speed in degrees in the
same way as film cameras.
0
SEC:
Displays the shutter speed in seconds.
[Setting Values: DEG, RSEC]
Memo :
0
“DEG” display is enabled only when the frame
rate of [WFrame & Bit Rate] is set to “25p” or
“24p”.
When [WFrame & Bit Rate] is set to other values,
the shutter display setting is fixed at “SEC” and
cannot be selected.
(A P133 [ W Frame & Bit Rate ] )
0
When a remote control unit is connected to the
[REMOTE1] terminal, or when KA-M790G is
connected to the camera and RM-HP790 to KA-
M790G, “SEC” is displayed and selection is
disabled.
124
LCD/VF Menu
Menu Display and Detailed Settings