User manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
SD Set Up
For selecting whether to add a setup signal to the
video signal output from the [VIDEO OUT] terminal.
Setup signals are added when “7.5%” is selected.
[Setting Values: 7.5%, 0.0%]
(Default values: 7.5% (U model), fixed at “0.0%” (E
model))
Memo :
0
Depending on the menu settings of the camera
recorder and the condition of the cable
connected to it, the setup signal setting may be
fixed at “0.0%”. “0.0%” is displayed in gray in this
case.
HDMI Out Character
For selecting whether to display the screen text and
menu text on the output screen from the [HDMI]
output terminal located at the side terminal section
of the camera recorder.
[Setting Values: On, ROff]
SDI Out Character
For selecting whether to display the screen text and
menu text on the output screen from the [HD/SD
SDI OUT] terminal located at the side terminal
section of the camera recorder.
[Setting Values: On, ROff]
VIDEO Out Character
For selecting whether to display the screen text and
menu text on the output screen from the [VIDEO
OUT] terminal located at the side terminal section
of the camera recorder.
[Setting Values: On, ROff]
Genlock Input A B
For selecting the input destination of video
synchronizing signals.
0
SDI:
Inputs video synchronizing signals from the [HD/
SD SDI IN] terminal on the side.
0
Adapter:
Inputs video synchronizing signals from the
adapter connected to the accessory connection
terminal (68 pins) on the rear of the camera
recorder.
0
BNC:
Inputs video synchronizing signals from the
[GENLOCK] terminal on the side.
[Setting Values: SDI, Adapter, RBNC]
Genlock Adjust
Adjusts the H Phase of the camera recorder’s video
signals with respect to the input synchronizing
signals.
9
Analog SD H Phase
Adjusts the H Phase of the camera recorder’s SD
analog signal with respect to the external
synchronizing signal input to the terminal set in the
[Genlock Input] item.
[Setting Values: -28 to +82] (R 0)
9
Analog HD H Phase A B
Adjusts the H Phase of the camera recorder’s HD
analog signal with respect to the external
synchronizing signal input to the terminal set in the
[Genlock Input] item.
[Setting Values: -1024 to +1023] (R 0)
9
SD-SDI H Phase
Adjusts the H Phase of the camera recorder’s SD-
SDI signal with respect to the external
synchronizing signal input to the terminal set in the
[Genlock Input] item.
[Setting Values: -373 to +373] (R 0)
Memo :
0
When [A/V Set] B [Video Set] B [HDMI/SDI
Out] B [Resolution] is set to “720p”/“1080i”/
“1080p”, “---” is displayed and selection is
disabled.
(A P125 [ Resolution ] )
9
HD-SDI H Phase
Adjusts the H Phase of the camera recorder’s HD-
SDI signal with respect to the external
synchronizing signal input to the terminal set in the
[Genlock Input] item.
[Setting Values: -1024 to +1023] (R 0)
Memo :
0
When [A/V Set] B [Video Set] B [HDMI/SDI
Out] B [Resolution] is set to “480i”/“480p”/“576i”/
“576p”, “---” is displayed and selection is
disabled.
(A P125 [ Resolution ] )
126
A/V Set Menu
Menu Display and Detailed Settings