User manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Time Code Operation Mode
Three types of time code operation (“FREE”,
“REC”, “REGEN”) can be selected with the [TC
GENE.] switch.
Setting Description
FREE
0
The time code operates in the
run mode at all times
regardless of the recording
status.
0
It continues to run even when
the power of the camera
recorder is turned off.
0
Synchronizes with the external
time code when an external
time code generator is
connected.
(A P78 [Synchronizing the
Time Code with an External
Time Code Generator] )
REC The time code operates in the run
mode during recording. It
continues to run in the order of the
recorded clips as long as the SD
card is not replaced. If the SD card
is removed and recording is made
on another card, time code will be
recorded on the new card from
where it was left off in the previous
card.
REGEN The time code operates in the run
mode during recording. When the
SD card is replaced, the last time
code recorded on the card is read
and recorded on a new card so that
the time code continues in running
order.
(A P74 [Presetting the Time
Code] )
Memo :
0
When [Main Menu] B [System] B [Record Set]
B [Rec Mode] is set to “Variable Frame”,
“Interval Rec” or “Frame Rec”, and the [TC
GENE.] switch is set to “FREE”, Rec Run mode
is activated.
(A P135 [ Rec Mode ] )
0
When [Main Menu] B [System] B [Record Set]
B [Record Format] B [WFormat]/[YFormat] is
set to “AVCHD”, Pre Rec enters Free Run mode.
(A P133 [ W Format ] )
(A P134 [ Y Format ] )
Setting Time Code
Generator
Presetting the Time Code
0
Time code and user’s bit data generated from
the internal time code generator are recorded.
0
This section describes how to set [TC/UB] B [TC
Preset].
(A P119 [ TC Preset ] )
Memo :
0
When the frame rate in [Main Menu] B [System]
B [Record Set] B [Record Format] B [WFrame
& Bit Rate]/[YFrame & Bit Rate] is set to “50p”,
“50i”, “25p” or “24p”, setting to “Drop” is
disabled.
(A P133 [ W Frame & Bit Rate ] )
(A P134 [ Y Frame & Bit Rate ] )
0
You can configure the setting without accessing
the [TC/UB] menu screen.
(A P75 [Setting Time Code without Opening
the Menu] )
Required Settings Before Preset
.
1
Set the [TC GENE.] switch to “REC” or
“FREE”.
0
[REC]:
Preset data in the time code generator
operates in run mode during recording
mode. Set this when recording continuous
time code in connecting frames.
0
[FREE]:
Time code starts to operate in run mode from
the preset time in the time code generator.
Time Code and User’s Bit
73
Shooting