INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Camera Function Menu
Menu screen for specifying operation settings
during shooting.
This item can only be selected in the Camera
mode.
Bars
For setting whether to output color bars.
[Setting Values: On, ROff]
Memo :
0
The audio test signals (1 kHz) can be output
simultaneously with the color bar output.
(A P129 [ Test Tone ] )
0
This feature will be set to “Off” automatically if
you switch the camera recorder from the
Camera mode to other modes or set the
[POWER ON/OFF
] switch to “OFF”.
OIS F
For setting whether to enable image stabilizer.
When “On” is selected, set the Level.
[Setting Values: On, ROff]
* When the supplied lens is not attached, “---” is
displayed and selection cannot be made.
9
Level
For setting the level of the image stabilizer.
[Setting Values: High, RNormal]
Memo :
0
When “High” is selected, correcting severe
camera shake may cause the area surrounding
the image to darken.
Flicker Correction
For setting whether to adjust image flicker that
occurs under a fluorescent light.
[Setting Values: On, ROff]
Memo :
0
In any of the following cases, “Off” is displayed
and selection cannot be made.
0
During slow shutter
0
When [Rec Mode] is set to “Variable Frame
”
0
When the
number of frames of [WFrame & Bit
Rate]/[YFrame & Bit Rate] is “24p”
Flash Band Correction
For reducing the condition of the flash band
phenomenon, which creates an unnatural image
with a part of it brightly lit, such as by the camera
flash of another still camera.
[Setting Values: On, ROff]
Caution :
0
Flash band
correction function is not available in
any of the following cases.
0
When [Rec Mode] is set to “Variable Frame”
0
When the
frame rate of [WFrame & Bit Rate]/
[YFrame & Bit Rate] is “24p”
0
When the
shutter speed is set to a value other
than OFF
(A P60 [Manual Shutter Mode (Manual
Shutter Switching)] )
0
When [Network] is set to “On(SDI Off)” or
“On(HDMI Off)”
0
[Flash Band Correction
] operates when the
luminance of the screen varies widely, with or
without flash light. However, depending on the
shooting condition, the flash band correction
may not be fully effective even if there are flash
lights.
0
The following symptoms may occur under flash
light, but these are not malfunctions due to flash
band correction.
0
Moving object appears to be stationary
momentarily.
0
A horizontal line appears on the image.
0
The [Flash Band Correction] feature will be set
to “Off
” automatically if you switch the camera
recorder from the Camera mode to other modes
or set the [POWER ON/OFF] switch to “OFF”.
Shutter
For specifying shutter-related settings.
Use this item to set to “Step” (fixed value) or
“Variable” when operating with the cross-shaped
button (JK) on the right side.
0
EEI:
Select this to perform automatic control of the
shutter.
0
Variable:
Sets to variable scan. Use this setting such as
when shooting a PC monitor.
0
Step:
Sets to step shutter, which switches the shutter
speed by a fixed value.
[Setting Values: EEI, Variable, RStep]
108
Camera Function Menu
Menu Display and Detailed Settings