INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
1
Set the camera recorder to the Camera
mode.
(A P18 [Operation Modes] )
2
Set [Genlock Input
] to “BNC”. A B
Set [A/V Set] B [Video Set] B [Genlock Input] to
“BNC”.
(A P126 [ Genlock Input A B ] )
Memo :
0
Set to “Adapter” to input synchronizing signal
from the accessory connection terminal (68
pins) on the rear of this unit.
3
When in the standby or stop mode, input
synchronizing signals from the SYNC
signal generator to the
[
GENLOCK]
terminal.
0
When the
camera recorder’s video is locking
to the external synchronizing signal, “Sync
Locking” appears on the screen.
0
After locking to the external synchronizing
signal is complete, the display disappears
and recording can be performed.
0
If there is genlock signal input but the signal
format is not supported, “Invalid Sync” is
displayed.
Memo :
0
If the frame rate of [WFrame & Bit Rate]/
[YFrame & Bit Rate] in the [Record Format]
menu is set to “60p
”, “60i”, “30p”, or “24p”,
59.94 Hz synchronizing signals (vertical
synchronization) are input.
50 Hz/60 Hz synchronizing signals are not
synchronized.
0
If the frame rate of [WFrame & Bit Rate]/
[YFrame & Bit Rate] in the [Record Format]
menu is set to “50p
”, “50i”, or “25p”, 50 Hz
synchronizing signals (vertical synchronization)
are input.
59.94 Hz/60 Hz synchronizing signals are not
synchronized.
(A
P133 [ W Frame & Bit Rate ] )
(
A P134 [ Y Frame & Bit Rate ] )
0
Do not
connect or disconnect the input cable for
the synchronizing signals during recording or
playback
0
If the power is turned on during input of external
synchronizing signals, vertical oscillation may
occur. This is not a malfunction.
0
Signals such as VTR playback signals with
jitters may not be synchronized on this camera
recorder.
0
Only H (Horizontal) and V (Vertical) genlock
functions are
available on this camera recorder.
It does not come with a lock function for SC (sub-
carrier). Color flash may occur during switching
such as when composite signals are used by a
switcher.
o Phase Items to Synchronize
The phase items to be synchronized may vary
depending on the input synchronizing signal and
output video signal.
Output Video Signal
Input Synchronizing
Signal
BB Tri-sync
720p 1080i
VIDEO Composite H, V, F V V, F
Y/PB/PR
A
B
SD
Component
H, V, F V V, F
HD
Component
720p
V H, V V
HD
Component
1080i
V, F V H, V, F
HD/SD
SDI
SD-SDI H, V, F V V, F
HD-SDI
720p
V H, V V
HD-SDI
1080i
V, F V H, V, F
H : Horizontal Phase
V
:
Vertical Phase
F : Field Phase
For digital signals (SDI) input A B
Input external synchronizing signals from the [HD/
SD SDI IN]
terminal, and synchronize the camera
video with the external signal.
o Synchronizing signal used
SD synchronizing
signal
: Supports SMPTE259M
HD synchronizing
signal
: Supports SMPTE292M
.
HD/SD SDI IN
External Synchronizing Signal
SDI Signal
Generator
170
Inputting External Synchronizing Signals (Genlock)
Connecting External Devices