INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
AE Level
For setting the convergence level during AE (Auto
Exposure).
This can also be adjusted using the cross-shaped
button (HI) on the right side.
[Setting Values: -6 to +6 (R0)]
Memo :
0
In all the following cases, “---” is displayed and
selection cannot be made.
0
When gain is set to a value other than “ALC”
0
When [Shutter]
is set to a value other than
“EEI”
0
When
the
[IRIS A/M] selection switch is set to
“M” (only when the supplied lens is used)
AE Speed
For setting
the convergence speed during AE (Auto
Exposure).
[Setting Values: RFast, Middle, Slow]
ALC Limit
For setting the maximum gain value of “ALC
”,
which electrically boosts the sensitivity level
according to the brightness automatically.
[Setting Values: 24dB, R18dB, 12dB, 6dB]
Auto Iris Limit (OPEN)
For setting the limit value of the OPEN end when
auto iris is enabled.
[Setting Values: F5.6, F4, F2.8, F2, F1.6, RF1.4]
Auto Iris Limit (CLOSE)
For setting the limit value of the CLOSE end when
auto iris is enabled.
[Setting Values: RF16, F11, F8, F5.6]
EEI Limit
For setting the shutter speed control range when
the Automatic Shutter mode (EEI) is enabled.
[Setting Values: 4F-stop, R3F-stop, 2F-stop]
Smooth Trans
For setting the shock reduction function, which
slows down the sudden change when switching
with the [GAIN L/M/H] selection switch or
[
WHT.BAL B/A/PRESET] switch.
[Setting Values: Fast, Middle, Slow, ROff]
Memo :
0
This feature does not function when the [FULL
AUTO] switch is “ON”, while the [GAIN L/M/H]
selection switch or [WHT.BAL B/A/PRESET]
switch is disabled.
FAW
For setting where to assign the FAW (Full Auto
White Balance) feature in the [WHT.BAL B/A/
PRESET
] switch.
[Setting Values: B, A, PRESET, RNone]
Memo :
0
When the [FULL AUTO] switch on the camera
recorder is set to “ON”, and [FULL AUTO] B
[White Balance
] is set to “FAW”, the setting is
fixed at
“FAW”.
GAIN L, GAIN M, GAIN H
For setting the gain value of each position on the
[GAIN L/M/H]
selection switch.
When “ALC” is selected, the camera recorder
switches to the Auto Gain mode.
[Setting Values: ALC, 24dB, 21dB, 18dB, 15dB,
12dB, 9dB, 6dB, 3dB, 0dB, -3dB, -6dB]
(Default values GAIN L: 0dB, GAIN M: 6dB, GAIN
H: 12dB)
Memo :
0
When the [FULL AUTO] switch on the camera
recorder is set to “ON”, and [FULL AUTO] B
[Gain] is set to
“ALC”, the setting is fixed at
“ALC
”.
AE LEVEL SW
For specifying the operation of the cross-shaped
button (HI) on the right side.
0
AE LEVEL/VFR:
Sets the number of frames during Variable
Frame Rec,
and operates as the AE level setting
button in other cases.
(A P93 [Variable Frame Rec] )
0
AE Level:
Operates as the AE level setting button at all
times.
0
Disable:
Disables the button.
[Setting Values: AE LEVEL/VFR, RAE Level,
Disable]
Camera Function Menu
109
Menu Display and Detailed Settings