INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Adjusting Back Focus
When the lens is first attached, adjust the back
focus of the lens if the focus is not clear when
zoomed to the telephoto or wide angle end.
0
Place an object 3 m and above away from the
camera recorder.
0
The Siemens Star Chart is most suitable as the
subject.
.
Siemens Star Chart
.
6, 9
2
3, 84
2, 10
1
1
Set the [ZOOM SERVO/MANUAL] switch to
“MANUAL”
.
2
Press and hold down the [IRIS]
button, and
press the [F.f] back focus button until the
indicator lamp lights up (approx. 1.5
seconds).
3
Turn the zoom ring to set the lens to the
maximum telephoto position.
4
Turn the focus ring to adjust the focus of
the object.
5
Turn the zoom ring to set the lens to the
maximum wide angle position.
6
Adjust the back focus using the iris ring to
set the focus on the subject.
7
Repeat steps 3 to 6
a few times until focus
is
set on both the telephoto and wide-angle
ends.
8
Turn the zoom ring and check if the image
is blurry at the telephoto end at the 20 mm
scale mark.
9
If blurring occurs, turn the iris ring to adjust
the focus. (It is recommended to set the
zoom ring near the 40 mm scale mark.)
10
Press the [F.f] back focus button until the
indicator lamp goes off (approx. 0.5
second).
Memo :
0
The iris
is fixed at the maximum position. Adjust
the lighting, shutter and gain to obtain an
appropriate video level.
Adjusting Back Focus
41
Preparations