INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
2
Select the framing mode for the time code
generator (only
when the frame rate setting
is “60” or “30”).
Set using [Main Menu] B [TC/UB] B [Drop
Frame].
(A P
119 [ Drop Frame ] )
0
[Drop]:
Sets the
run mode of the time code generator
to drop frame mode. Use this setting when
placing emphasis on the recording time.
0
[Non Drop]:
Sets
the run mode of the time code generator
to non-drop frame mode. Use this setting
when placing emphasis on the number of
frames.
Memo :
Drop frame/non-drop frame mode
0
When the frame rate setting in [Main Menu]
B
[System] B [Record Set] B [Record Format] B
[Frame & Bit Rate] is “60p”, “60i”, or “30p”, the
actual number of frames per second is
approximately 59.94 (29.97). However, the time
code processing standard is “60p”, “60i”, or
“30p” frames. To make up for the frame number
discrepancy, the drop frame mode (Drop) drops
the 00 frame and 01 frame every minute except
for minutes that are multiples of 10. However, in
the case of “60p”, the 00, 01, 02 and 03 frame
are dropped.
0
The
non-drop
frame mode (Non Drop) does not
drop frames and ignores the discrepancy with
the actual time.
Presetting the Time Code
.
1
Select [Main Menu]
B [TC/UB] B [TC Preset]
and press the Set button (R).
(A P119 [ TC Preset ] )
The [TC Preset
] screen appears.
.
1
TC Preset
TC/UB
Memo :
0
When the
[TC GENE.] switch is set to “REGEN”,
the parameter is displayed as “Regen” and
selection is disabled.
2
Set the time code (hour, minute, second,
frame).
Use the cross-shaped button (HI) to place the
cursor at the item to set, then use the cross-
shaped button (JK) to change the values.
.
TC Preset
TC/UB
During drop frame
During
non-drop frame
Cursor
Memo :
0
Press the [MARKER/2] button to reset each digit to
“0”. The cursor moves to the time digit (left).
3
Check the values and press the Set button
(R).
0
The time code is set and the screen returns
to [TC/UB].
0
To cancel the setting, press the [CANCEL]
button.
4
Press the [MENU/THUMB] button.
Returns to the normal screen.
74
Setting Time Code Generator
Shooting