INSTRUCTIONS MANUAL DE INSTRUCCIONES EN SP HARD DISK CAMERA VIDEOCÁMARA GZ-HD320 GZ-HD300 U U Dear Customers Thank you for purchasing this camcorder. Before use, please read the safety information and precautions contained in pages 2 and 3 to ensure safe use of this product. For Future Reference: Enter the Model No. (located on the bottom of the camcorder) and Serial No. (located on the battery pack mount of the camcorder) below. Model No. Serial No.
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Easy Start Guide Charge the battery before recording Turn off the camcorder and attach the battery pack. Access lamp blinks: Accessing files Power/charge lamp blinks: Charging goes out: Charging finished Do not remove the AC adapter, the battery pack or the microSD card when the lamp is blinking. Open the cover Battery Pack The battery pack is not charged at the time of purchase. AC Adapter To AC Outlet (110V to 240V) CAUTION • Be sure to use JVC battery packs.
Date/Time Setting the LCD monitor to Q Open turn on the camcorder the city closest to T Select the area where you use the camcorder Power button LCD monitor [YES] within R Select 10 seconds [ON] if daylight U Select saving time is observed Slide your finger up and down on the sensor. Then touch OK. V Set the date and time • When the message disappears, press the power button for at least 2 seconds to turn off the power, and then press it again for at least 2 seconds.
Video recording CAUTION Before recording an important scene, it is recommended to conduct a trial recording. Q Slide the mode switch to select ! (video) mode R Select recording mode (REC) The mode changes when you press the button. The auto recording indicator appears. S Start recording Remaining space on the hard disk Video Quality Press the START/STOP button to start recording, and press it again to stop.
Playing back Q Select playback mode (PLAY) The mode changes when you press the button. R Select the desired file S Select F (Touch OK) Index screen Playback screen To perform operations such as forward search or reverse search (Z p. 21) To view files on TV (Z p. 24) CAUTION Do not forget to make copies after recording! • To copy files onto discs (Z p. 27) • To dub files to a VCR/DVD recorder (Z p. 29) • To edit files on your computer (Z p.
Contents GETTING STARTED Index.........................................................10 Indications on LCD Monitor....................12 Accessories.............................................14 Preparing the Remote Control....................... 14 Necessary Settings before Use..............15 Charging the Battery Pack............................. 15 Date/Time Setting.......................................... 15 Language Setting.......................................... 16 Other Settings..............
How to use the Touch Sensor After the menu is displayed on the LCD monitor: Read This First! Make a backup of important recorded data It is recommended to copy your important recorded data to a DVD or other recording media for storage. JVC will not be responsible for any lost data. Make a trial recording Before the actual recording of important data, make a trial recording and play back the recorded data to check that the video and sound have been recorded correctly.
GETTING STARTED Index NOTE • Be careful not to cover 3, 4, 5, and 6 during shooting. • The LCD monitor can rotate 270°.
Camcorder ! # $ % & ( ) Power Button HDMI Mini Connector (Z p. 24) Component Connector (Z p. 24) DISPLAY Button (Z p. 13) Speaker Ventilation hole Zoom Lever (Z p. 20) Speaker Volume Control * SNAPSHOT Button (Z p. 19) + Touch Sensor , OK Button - MENU Button . Mode Switch [!, #] / UPLOAD Button (Z p. 36) TITLE Button 0 EXPORT Button (Z p. 35) 1 DIRECT DISC Button (Z p. 28) INFO Button (Z p. 20) 2 PLAY/REC Button (Z p. 18, 19, 21, 22) 3 4 5 6 LED Light (Z p.
Indications on LCD Monitor During both Video and Still Image Recording N OV. 1 . 2 0 0 9 4:55 PM ! Selected Recording Mode Indicator (Z p. 23) @: Auto Mode 3: Manual Mode # Effect Mode Indicator $ Tele Macro Mode Indicator % LED Light Indicator (Z p. 20) & Scene Select Indicator ( Zoom Indicator (Z p. 20) ) Recording Medium Indicator * Drop Detection Indicator (Appears when [DROP DETECTION] is set to [OFF].) + White Balance Indicator , Monitor Backlight Indicator - Battery Indicator . Date/Time (Z p.
During Video Playback During Still Image Playback 8 N OV. 1 . 2 0 0 9 4:55 PM ! Mode Indicator # Wipe/Fader Effect Indicator $ Playlist Playback Indicator (Appears when playing back a playlist.) % Quick Review Indicator (Z p. 18) & Video Quality ( Counter ) Playback Mode F: Playback Q: Pause K: Forward Search J: Reverse Search QF: Forward Slow-Motion PQ: Reverse Slow-Motion (The number on the left shows speed.) * + , . Battery Indicator Date/Time (Z p. 15) Volume Level Indicator x.v.
Accessories AP-V20U BN-VF808U AC Adapter Battery Pack Component Cable AV Cable CR2025 RM-V751U USB Cable Remote Control Lithium Battery Pre-installed in the remote control. CD-ROM NOTE Make sure to use the provided cables for connections. Do not use any other cables. Preparing the Remote Control A battery is included inside the remote control at the time of purchase. Remove the insulation sheet before use.
Necessary Settings before Use Charging the Battery Pack 1 2 To detach the battery pack Close the LCD monitor to turn off the camcorder. Attach the battery pack, then connect the AC adapter. NOTE • You can also use the camcorder with just the AC adapter. • The actual recording time may shorten depending on the recording environment, such as when recording scenes with fast moving subject. • Please do not pull or bend the AC adapter plug and cable. This may damage the AC adapter.
Necessary Settings before Use (Continued) 5 6 Select [CLOCK SETTING]. Select the city closest to the area where you use the camcorder. Selected area is highlighted Principal city of the selected area 6 Select the city closest to the area you are traveling. To return to the previous screen Select @. To quit the screen Select [QUIT]. Time difference to GMT 7 8 9 Language Setting Select [ON] if daylight saving time is observed. Set the date and time.
Other Settings Using a microSD Card The camcorder is programmed to record on the built-in hard disk when it is shipped from the factory. You can change the recording medium to microSD card. • Operations are confirmed on the following microSD cards. - Panasonic - TOSHIBA - SanDisk - ATP Video recording: Class 4 or higher compatible microSDHC card (4 GB to 8 GB) For UXP mode, use Class 6 or higher.
RECORDING/PLAYBACK Recording Files Video Recording Slide the mode switch to select ! (video) mode. Press PLAY/REC to select the recording mode. SNAPSHOT Press START/STOP to start recording. Approximate remaining time for recording You can also start/stop recording by selecting [REC] on the LCD monitor. (On-screen recording control) To stop recording Press START/STOP again. To change the video quality Change the settings in [VIDEO QUALITY].
Still Image Recording Slide the mode switch to select # (still image) mode. Press PLAY/REC to select the recording mode. Press and hold SNAPSHOT halfway. The ? indicator becomes green when the captured image is focused. Press SNAPSHOT fully to take a still image. To view the last recorded image Select A after shooting. Selecting $ during playback deletes that image. To change the image quality Change the settings in [IMAGE QUALITY]. To change the image size Change the settings in [IMAGE SIZE].
Recording Files (Continued) Checking the Remaining Battery Power Zooming Preparation: • Select ! or # mode. • Select the recording mode. Zoom out ! mode: Zoom in Press INFO twice or INFO and then select ;. # mode: Press INFO. W: Wide angle T: Telephoto You can also zoom out/zoom in by selecting [W] or [T] on the LCD monitor. (On-screen zoom control) To quit the screen Select [QUIT] or press INFO.
Playing Back Files Video Playback Slide the mode switch to select ! (video) mode. Press PLAY/REC to select the playback mode. The index screen appears. Select the desired file. To move to the previous or next page Touch [ ] or [ ] for over a second. To play back a few seconds from the beginning of each video Touch [ ]. NOTE • In some cases, parts of video other than the beginning may be played back. • Some video may not be played back at all. To delete a video Select $ when playback is stopped.
Playing Back Files (Continued) Still Image Playback Slide the mode switch to select # (still image) mode. Press PLAY/REC to select the playback mode. The index screen appears. Select the desired file. To move to the previous or next page Touch [ ] or [ ] for over a second. To delete a still image Select $. To change the number of thumbnails (6 thumbnails/12 thumbnails) Move the zoom lever to [W]. To zoom in the image during playback (Remote Control Only) Press T on the remote control.
Manual Recording Manual recording mode enables you to set the focus and screen brightness, etc. manually. Manual Setting in Menu In the manual recording mode: Changing to Manual Recording Mode Preparation: • Select ! or # mode. • Select the recording mode. 1 2 Touch MENU. Select [MANUAL SETTING]. Select [A/M] twice. 3 Select the desired menu. 4 Select the desired setting. To return to the auto recording mode Select [A/M] so that the @ indicator appears.
USING WITH TV Viewing Files on TV This camcorder is designed to be used with high-definition or NTSC-type color television signals. It cannot be used with a television of a different standard. Connection with TV You can output videos from the HDMI connector, COMPONENT connector, or AV connector. Select the connector that best suits your television. Preparation: Turn off all units. To connect using the HDMI mini connector We recommend using the Category 2 HDMI cable (High Speed cable).
To connect using the AV connector DC Connector AV Connector Playback Operation After the connection with TV is completed 1 2 3 AC Adapter 4 To AC Outlet AV Cable Turn on the camcorder and the TV. Set the TV to its VIDEO mode. (Only when connecting the camcorder to the VCR/DVD recorder) Turn on the VCR/DVD recorder, and set the VCR/DVD recorder to its AUX input mode. Start playback on the camcorder. (Z p. 21, 22) To display camcorder’s on-screen display on TV Set [DISPLAY ON TV] to [ON].
EDITING Managing Files CAUTION Do not remove the recording medium or perform any other operation (such as turning off the power) while accessing files. Also, be sure to use the provided AC adapter, as the data on the recording medium may be corrupted if the battery becomes exhausted during operation. If the data on the recording medium becomes corrupted, format the recording medium to use the medium again.
COPYING Copying Files Types of Copying and Connectable Device The Camcorder You can copy files between the HDD and microSD card with this camcorder alone. DVD Burner CU-VD50/CU-VD3 You can copy files recorded on this camcorder onto discs. BD Burner LaCie Model No. 301828 You can copy files recorded on this camcorder onto discs. - Playback the disc using the camcorder. Playback the disc using a BD/DVD burner.* Playback on a PC.* Playback the disc using a BD/DVD player that supports BD-MV and AVCHD.
Copying Files (Continued) Backup All Files 5 Preparation: • Select ! or # mode. • Select HDD or microSD card. • Connect the camcorder to the BD/DVD burner. • When using a BD burner, select [CHANGE REC. MEDIA] and select the disc type. 1 Select [CREATE FROM ALL] (! mode) or [SAVE ALL] (# mode). [COMPLETED] appears, touch OK. [STOP] TO EXIT CREATE] appears, change the disc. Remaining files are copied on the second disc. • To cancel copying, select [STOP].
Dubbing Files to a VCR/DVD Recorder Preparation: • Create a playlist. • Turn off all units. 1 2 DC Connector AV Connector Set the VCR/DVD recorder to its AUX input mode. Check that the images from the camcorder are input correctly to the VCR/DVD recorder. To connect using the AV connectors (analog dubbing) AC Adapter Open the LCD monitor to turn on the camcorder. 3 Play back playlists on the camcorder. 1) Touch MENU. 2) Select [DUBBING PLAYBACK]. 3) Select the desired playlist.
PC OPERATION Creating a Disc Using a PC Please read the “JVC Software License Agreement” in the CD-ROM instruction before you install software. You can copy the data from the camcorder and create a disc using a PC. Q 1 Click [Easy Installation]. Installing the software to the PC System Requirements Windows Vista OS: Windows Vista® Home Basic (SP1) Home Premium (SP1) (32-bit, pre-installed) Follow the on-screen instructions. 2 Click [Next]. 3 Click [Finish]. CPU: Intel® CoreTM Duo, 1.
R Making Backup on the PC 3 Click [All volume in camcorder] and click [Next]. Preparation: • Install the software to the PC. • Make sure that enough free space is left in the PC’s HDD. • Close the LCD monitor to turn off the camcorder. USB Connector 4 Click [Start]. Backup starts. USB Cable USB Connector 1 2 Open the LCD monitor to turn on the camcorder.
Creating a Disc Using a PC (Continued) Making User Lists to Arrange the Files S 5 Click the recording date. You can make a user list of a certain subject (such as Travel, Athletic meet) and put the files related to the subject into the user list. Preparation: Make backup on the PC. 1 2 Double-click the icon to open the calendar. The files recorded on the day are displayed. 6 Drag the file and drop into the user list. Select [Movies only].
Copying Files to a disc T 4 Everio MediaBrowser supports 3 disc formats. Select the one that suits your purpose. DVD-Video disc: Drag the file, and drop into the part at the bottom and click [Next]. Suitable if you will give the disc to your friends and relatives. AVCHD disc: Suitable for high quality video. BD: 1 2 3 Suitable for high quality video with long recording time. 5 Select the user list and click [Create Disc]. 6 Input the disc name, select the top menu style and click [Next].
Creating a Disc Using a PC (Continued) Folder Structure and Extensions EVERIO_HDD X = number EVERIO_SD [DCIM] [XXXJVCSO] Contains the still image folders. [DCIM] [XXXJVCSO] [EXTMOV] [DEM_XXXX.MTS] [MOV_XXXX.MTS] Video files with defective management information are saved. [EXTMOV] [DEM_XXXX.MTS] [MOV_XXXX.MTS] [PRIVATE] [AVCHD] Contains management information files of event and/or disc creation information for the files taken with the camcorder. [BDMV] [STREAM] [XXXXX.
Using with a Portable Media Player To cancel the export setting Select the file and select [ ] again. Turning on the Export Mode You can easily transfer videos recorded in export mode to iTunes®. All the files with the export setting turned on are transferred to PC. For details on transferring, refer to the operation guide of MediaBrowser in the CDROM. Preparation: • Select ! mode. • Select the recording mode. To quit the screen 1) Select [DONE]. 2) Select [YES].
Uploading Files to Websites Turning on the Upload Mode You can upload the file to video sharing websites (YouTube™) quickly after recording. Preparation: • Select ! mode. • Select the recording mode. Press UPLOAD twice. If you record a file with the upload mode set on, the recording stops automatically 10 minutes after the recording is started. The remaining time is displayed on the LCD monitor. NOTE The upload mode turns off each time recording is finished.
FURTHER INFORMATION Changing the Menu Settings 1 2 3 Touch MENU. To return to the previous screen Select @. Select the desired menu. To quit the screen Select [QUIT]. Select the desired setting. Troubleshooting Before requesting service, consult the following chart. If the solutions indicated in the chart do not solve the problem, consult your nearest JVC dealer or JVC service center for instructions. Refer also to the FAQ of new products on JVC’s website. Trouble Power No power is supplied.
Troubleshooting (Continued) Trouble Recording Recording cannot be performed. Action • Slide the mode switch to select the desired mode (! or #). • Such a phenomenon occurs when shooting a subject illuminated Vertical lines appear on recorded images. by bright light. This is not a malfunction. • Sometimes playback is interrupted at the connecting section Sound or video are interrupted. between two scenes. This is not a malfunction.
Warning Indications Indication Action SET DATE/TIME! • Set the clock. If the message still appears after setting the clock, the battery for the clock has been depleted. Consult your nearest JVC dealer. COMMUNICATING ERROR • Be sure to use JVC battery packs. CANNOT USE IN VIDEO MODE • Set [REC MEDIA FOR VIDEO] to [HDD]. • Replace the microSD card. (Files recorded with other devices NOT FORMATTED • Select [OK] and select [YES] to perform formatting.
Specifications General Power supply DC 11 V (Using AC adapter) DC 7.2 V (Using battery pack) Power consumption Approx. 3.5 W* * When the LED light is off and the monitor backlight is set to [STANDARD] mode. Rated Current Consumption: 1A Dimensions (W x H x D) 53 mm x 68 mm x 113 mm (2-1/8" x 2-11/16" x 4-1/2") Weight Approx. 325 g (0.7 lbs) Approx. 370 g (0.8 lbs) (incl.
h: hour/m: minute Approximate recordable time (for video) HDD Recording medium microSD Card GZ-HD300 60 GB GZ-HD320 120 GB 4 GB 8 GB UXP 5 h 30 m 11 h 20 m 40 m XP 7 h 30 m 15 h 30 m 1 h 00 m SP 10 h 21 h 44 m 1 h 28 m EP 25 h 50 h 1 h 40 m 3 h 20 m Quality Approximate number of images (for still image) The HDD can record up to 9999 still images in either mode.
Cautions AC Adapter When using the AC adapter in areas other than the USA The provided AC adapter features automatic voltage selection in the AC range from 110 V to 240 V. USING HOUSEHOLD AC PLUG ADAPTER In case of connecting the unit’s power cord to an AC wall outlet other than American National Standard C73 series type use an AC plug adapter, called a “Siemens Plug”, as shown. For this AC plug adapter, consult your nearest JVC dealer.
Main Unit • For safety, DO NOT ... open the camcorder’s chassis. ... disassemble or modify the unit. ... allow inflammables, water or metallic objects to enter the unit. ... remove the battery pack or disconnect the power supply while the power is on. ... leave the battery pack attached when the camcorder is not in use. ... place naked flame sources, such as lighted candles, on the apparatus. ... expose the apparatus to dripping or splashing. ...
Terms A B C D E F H I L AC Adapter . .................................................15, 42 AV Connection .............................................25, 29 Battery Pack .................................................15, 42 BD/DVD Backup .................................................27 BD/DVD Burner ..................................................27 CD-ROM ......................................................14, 30 Clock Adjust .......................................................
MEMO
Precauciones de seguridad ADVERTENCIA: PARA EVITAR RIESGO DE INCENDIOS O ELECTROCUCIONES, NO EXPONGA ESTE APARATO A LA LLUVIA O HUMEDAD. NOTAS: • La placa de valores nominales y la precaución de • • seguridad se encuentran en la parte inferior y/o en la parte posterior de la unidad principal. La placa del número de serie se encuentra en el compartimiento de la batería.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD 1. 2. 3. 4. 5. 6. 7. Lea estas instrucciones. Conserve estas instrucciones. Preste atención a las advertencias. Siga todas las instrucciones. No utilice este aparato cerca del agua. Limpie sólo con paño seco. No bloquee ninguna abertura de ventilación. Instale de acuerdo con las instrucciones del fabricante. 8. No lo instale cerca de ninguna fuente de calor tales como, radiadores, calefactores, cocinas, u otros aparatos (incluyendo amplificadores) que produzcan calor.
Guía de inicio rápido Cargue la batería antes de grabar Apague la videocámara e inserte la batería. Luz de acceso Parpadea: acceso a los archivos Luz de alimentación/carga Parpadea: carga en curso Se apaga: carga terminada Cuando esta luz parpadea, no extraiga el adaptador de CA, la batería ni la tarjeta microSD. Abrir la cubierta Batería La videocámara se suministra con la batería descargada. Adaptador de CA A la toma de CA (de 110 V a 240 V) PRECAUCIÓN • Asegúrese de utilizar baterías JVC.
Ajuste de la fecha/hora Q Abra la pantalla LCD para encender la videocámara la ciudad más T Seleccione cercana a la zona donde vaya a usar la videocámara Botón de alimentación Pantalla LCD [SÍ] en R Seleccione 10 segundos [ON] si el horario U Seleccione de verano está activado Deslice el dedo arriba y abajo por el sensor. A continuación, toque OK.
Grabación de vídeo PRECAUCIÓN Antes de grabar una escena importante se recomienda realizar una grabación de prueba. el interruptor de modo para seleccionar el modo ! Q Deslice (vídeo). R Seleccione el modo de grabación (REC) El modo cambia al pulsar el botón. Aparece el indicador de grabación automática. S Inicie la grabación Pulse el botón START/ STOP para iniciar la grabación y vuelva a pulsarlo para detenerla.
a de ción Reproducción Q Seleccione el modo de reproducción (PLAY) El modo cambia al pulsar el botón. R Seleccione el archivo que desee S Seleccione F (toque OK) Pantalla de índice Pantalla de reproducción Para realizar operaciones como búsqueda hacia adelante o búsqueda hacia atrás (Z p. 21) Para visualizar archivos en un televisor (Z p. 24) PRECAUCIÓN ¡No olvide realizar copias tras la grabación! • Para copiar archivos en discos (Z p.
Contenido PREPARATIVOS Índice........................................................10 Indicaciones en la pantalla LCD.............12 Accesorios...............................................14 Preparación del mando a distancia............... 14 Ajustes preliminares necesarios...........15 Carga de la batería........................................ 15 Ajuste de la fecha/hora.................................. 15 Ajuste del idioma........................................... 16 Otros ajustes.................
Cómo utilizar el sensor táctil Una vez que aparezca el menú en la pantalla LCD: Q Deslice el dedo arriba y abajo por el sensor. R Seleccione [AJUSTE]. (Toque OK.) A Para seleccionar un botón en pantalla que aparezca en el lado izquierdo, toque la parte del sensor que se encuentre junto al botón en pantalla. B Para seleccionar un botón en pantalla que aparezca en la parte inferior de la pantalla, toque el botón que se encuentre debajo de él.
PREPARATIVOS Índice NOTA • Procure no tapar 3, 4, 5, y 6 durante la filmación. • La pantalla LCD puede girar 270°.
Videocámara ! # $ % & ( ) Botón de alimentación Miniconector HDMI (Z p. 24) Conector componente (Z p. 24) Botón DISPLAY (Z p. 13) Altavoz Orificio de ventilación Palanca del zoom (Z p. 20) Control de volumen del altavoz * Botón SNAPSHOT (Z p. 19) + Sensor táctil , Botón OK - Botón MENU . Interruptor de modo [!, #] / Botón UPLOAD (Z p. 36) 0 Botón EXPORT (Z p. 35) Botón TITLE 1 Botón DIRECT DISC (Z p. 28) Botón INFO (Z p. 20) 2 Botón PLAY/REC (Z p. 18, 19, 21, 22) 3 4 5 6 Luz LED (Z p.
Indicaciones en la pantalla LCD Durante la grabación de vídeo e imágenes fijas N OV. 1 . 2 0 0 9 4:55 PM ! Indicador de modo de grabación seleccionado (Z p. 23) @: Modo automático 3: Modo manual # Indicador de modo de efectos especiales $ Indicador de modo telemacro % Indicador de luz LED (Z p. 20) & Indicador de selección de escena ( Indicador de zoom (Z p. 20) ) Indicador de soporte de grabación * Indicador de detección de caída (Aparece si [SENSOR DE GRAVEDAD] está ajustado en [OFF].
Durante la reproducción de vídeo Durante la reproducción de imágenes fijas 8 N OV. 1 . 2 0 0 9 4:55 PM ! Indicador de modo # Indicador de efectos de cortinilla/fundido $ Indicador de reproducción de lista de reproducción (Aparece al reproducir una lista de reproducción.) % Indicador de revisión rápida (Z p.
Accesorios AP-V20U BN-VF808U Adaptador de CA Batería Cable componente Cable AV CR2025 RM-V751U Cable USB Mando a distancia Pila de litio Preinstalada en el mando a distancia. CD-ROM NOTA Asegúrese de utilizar los cables suministrados para las conexiones. No utilice ningún otro cable. Preparación del mando a distancia El mando a distancia se suministra con una pila instalada. Antes de su uso, retire el plástico de aislamiento.
Ajustes preliminares necesarios Para extraer la batería Carga de la batería 1 2 Cierre la pantalla LCD para apagar la videocámara. Instale la batería y conecte el adaptador de CA. NOTA • La videocámara también se puede usar con sólo el adaptador de CA. • El tiempo de grabación real puede reducirse en función del entorno de grabación, como cuando se graban escenas con un sujeto en movimiento rápido. • No estire ni doble el enchufe o el cable del adaptador de CA. Se podría dañar el adaptador de CA.
Ajustes preliminares necesarios (continuación) 5 6 Seleccione [CONF. RELOJ]. 6 Seleccione la ciudad más cercana a la zona donde vaya a usar la videocámara. Para volver a la pantalla anterior Seleccione @. La zona seleccionada se resalta Seleccione la ciudad más cercana a la zona del viaje. Para salir de la pantalla Seleccione [SALIR]. Ciudad principal de la zona seleccionada Diferencia horaria con respecto a GMT 7 8 9 Seleccione [ON] si el horario de verano está en vigencia.
Otros ajustes Uso de una tarjeta microSD La videocámara está preajustada de fábrica para grabar en el disco duro integrado. El soporte de grabación se puede cambiar por una tarjeta microSD. • Se ha confirmado el funcionamiento con las siguientes tarjetas microSD. - Panasonic - TOSHIBA - SanDisk - ATP Grabación de vídeo: Tarjeta microSDHC compatible de clase 4 o superior (de 4 GB a 8 GB) Para el modo UXP, utilice la clase 6 o superior.
GRABACIÓN/REPRODUCCIÓN Grabación de archivos Grabación de vídeo Deslice el interruptor de modo para seleccionar el modo ! (vídeo). Pulse PLAY/REC para seleccionar el modo de grabación. SNAPSHOT Pulse START/STOP para empezar la grabación. Tiempo restante aproximado para la grabación También puede iniciar/detener la grabación seleccionando [REC] en la pantalla LCD. (Control de grabación en pantalla) Para detener la grabación Pulse START/STOP de nuevo.
Grabación de imágenes fijas Deslice el interruptor de modo para seleccionar el modo # (imagen fija). Pulse PLAY/REC para seleccionar el modo de grabación. Mantenga pulsado SNAPSHOT hasta la mitad de su recorrido. El indicador ? se vuelve verde cuando la imagen capturada queda enfocada. Pulse SNAPSHOT hasta el fondo para tomar una imagen fija. Para ver la última imagen grabada Seleccione A tras la toma. Si selecciona $ durante la reproducción, se elimina la imagen.
Grabación de archivos (continuación) Zoom Preparativos: • Seleccione el modo ! o #. • Seleccione el modo de grabación. Reducción Ampliación W: Gran angular T: Telefoto Comprobación de la carga restante de la batería Modo !: Pulse INFO dos veces o pulse INFO y seleccione ;. Modo #: Pulse INFO. También puede reducir/ampliar seleccionando [W] o [T] en la pantalla LCD.
Reproducción de archivos Reproducción de vídeo Deslice el interruptor de modo para seleccionar el modo ! (vídeo). Pulse PLAY/REC para seleccionar el modo de reproducción. Aparece la pantalla de índice. Seleccione el archivo que desee. Para pasar a la página anterior o siguiente Toque [ ] o [ ] durante más de un segundo. Para reproducir unos segundos del inicio de cada vídeo Toque [ ]. NOTA • En algunos casos, podrían reproducirse partes del vídeo distintas al principio.
Reproducción de archivos (continuación) Reproducción de imágenes fijas Deslice el interruptor de modo para seleccionar el modo # (imagen fija). Pulse PLAY/REC para seleccionar el modo de reproducción. Aparece la pantalla de índice. Seleccione el archivo que desee. Para pasar a la página anterior o siguiente Toque [ ] o [ ] durante más de un segundo. Para eliminar una imagen fija Seleccione $. Para cambiar el número de miniaturas (6 miniaturas/12 miniaturas) Mueva la palanca del zoom hacia [W].
Grabación manual El modo de grabación manual permite ajustar manualmente el enfoque, el brillo de la pantalla, etc. Ajuste manual en el menú En el modo de grabación manual: Cambio al modo de grabación manual Preparativos: • Seleccione el modo ! o #. • Seleccione el modo de grabación. 1 2 Toque MENU. Seleccione [AJUSTE MANUAL]. Seleccione [A/M] dos veces. Para regresar al modo de grabación automático Seleccione [A/M] para que aparezca el indicador @. 3 Seleccione el menú que desee.
USO CON EL TELEVISOR Visualización de archivos en un televisor Esta videocámara está diseñada para ser utilizada con señales de televisión en color de tipo NTSC o de alta definición. No se puede usar con un televisor de otra norma. Conexión con el televisor Los vídeos se pueden emitir por el conector HDMI, el conector COMPONENT o el conector AV. Seleccione el conector que se adecue mejor a su televisor. Preparativos: Apague todas las unidades.
Para realizar la conexión con el conector AV Adaptador de CA Conector de CC Conector AV Operación de reproducción Una vez realizada la conexión con el televisor 1 2 3 4 A la toma de CA Encienda la videocámara y el televisor. Ajuste el televisor en el modo de vídeo. (Sólo si conecta la videocámara a la grabadora de vídeo/DVD) Encienda la grabadora de vídeo/DVD y ajústela al modo de entrada AUX. Inicie la reproducción en la videocámara. (Z p.
EDICIÓN Gestión de archivos PRECAUCIÓN No extraiga el soporte de grabación ni realice ninguna otra operación (por ejemplo, apagar la alimentación) mientras se accede a los archivos. Asimismo, asegúrese de utilizar el adaptador de CA suministrado, ya que los datos del soporte de grabación se pueden dañar si la batería se agota durante la operación. Si los datos del soporte de grabación se dañan, deberá formatear el soporte de grabación para volver a usarlo.
COPIA Copia de archivos Tipos de copia y dispositivos conectables La videocámara Se pueden copiar archivos entre la unidad de disco duro y la tarjeta microSD en la propia videocámara. Grabadora de DVD CU-VD50/CU-VD3 Se pueden copiar en discos archivos grabados en esta videocámara. Grabadora de BD LaCie Nº de modelo 301828 Se pueden copiar en discos archivos grabados en esta videocámara. - Reproducción del disco mediante la videocámara. - Reproducción del disco con una grabadora de BD/DVD.
Copia de archivos (continuación) Copia de seguridad de todos los archivos 5 2 Seleccione [SELECC. ENTRE TODO] (modo !) o [GUARDAR TODO] (modo #). • Si aparece [INSERTAR SIGUIENTE DISCO PULSAR [CANCELAR] PARA ABANDONAR LA CREACIÓN], cambie de disco. Los archivos restantes se copiarán en el segundo disco. • Para cancelar la copia, seleccione [CANCELAR]. Copia de archivos de vídeo que nunca se han copiado Los archivos que nunca se han copiado en un disco se seleccionan y copian automáticamente.
Copia de archivos en una grabadora de vídeo/DVD 1 2 Preparativos: • Cree una lista de reproducción. • Apague todas las unidades. Conector de CC Conector AV Ajuste la grabadora de vídeo/DVD en el modo de entrada AUX. Asegúrese de que las imágenes de la videocámara se hayan introducido correctamente en la grabadora de vídeo/ DVD. Para realizar la conexión con los conectores AV (copia analógica) Adaptador de CA Abra la pantalla LCD para encender la videocámara.
FUNCIONAMIENTO DE PC Creación de un disco mediante un PC Lea, por favor, “Convenio de licencia del software de JVC” de las instrucciones del CD-ROM antes de instalar el software. Es posible copiar los datos de la videocámara y crear un disco utilizando un PC. Q 1 Haga clic en [Easy Installation].
R Copia de seguridad en un PC 3 Haga clic en [Todo el volumen en la videocamara] y en [Proximo]. Preparativos: • Instale el software en el PC. • Asegúrese de que dispone de suficiente espacio libre en el disco duro del PC. • Cierre la pantalla LCD para apagar la videocámara. Conector USB 4 Haga clic en [Comienzo]. Se inicia la copia de seguridad. Cable USB Conector USB 1 2 Abra la pantalla LCD para encender la videocámara. Seleccione [HACER COPIA DE SEGURIDAD].
Creación de un disco mediante un PC (continuación) Creación de listas personalizadas para organizar los archivos S 5 Haga clic en la fecha de grabación. Puede elaborar una lista personalizada de ciertos temas (por ejemplo, viajes, certámenes deportivos) e incluir los archivos relacionados con estos temas en la lista personalizada. Preparativos: Realice una copia de seguridad en el PC. 1 2 Haga doble clic en el icono y abra el calendario. Se muestran los archivos grabados en esa fecha.
Copia de archivos en un disco T 4 Everio MediaBrowser es compatible con 3 formatos de disco. Seleccione el que se adecue mejor a su propósito. Disco DVD-Video: Adecuado si desea dar el disco a amigos y familiares. Disco AVCHD: Adecuado para vídeo de alta calidad. BD: Adecuado para vídeo de alta calidad con un largo tiempo de grabación. 1 5 Escriba el nombre del disco, seleccione el estilo del menú superior y haga clic en [Proximo]. Seleccione la lista personalizada y haga clic en [Crear disco].
Creación de un disco mediante un PC (continuación) Estructura de carpetas y extensiones EVERIO_HDD X = número EVERIO_SD [DCIM] [XXXJVCSO] Contiene las carpetas de imágenes fijas. [DCIM] [XXXJVCSO] [EXTMOV] [DEM_XXXX.MTS] [MOV_XXXX.MTS] Se guardan archivos de vídeo con información de gestión defectuosa. [EXTMOV] [DEM_XXXX.MTS] [MOV_XXXX.MTS] [PRIVATE] [AVCHD] Contiene archivos de información de gestión del evento y/o información de creación de disco para los archivos grabados con la videocámara.
Utilización con un reproductor multimedia portátil Activación del modo de exportación Los vídeos grabados en el modo de exportación se pueden transferir fácilmente a iTunes®. Todos los archivos con el ajuste de exportación activado se transferirán al PC. Para obtener más información sobre cómo realizar la transferencia, consulte la guía de funcionamiento de MediaBrowser que aparece en el CD-ROM. Preparativos: • Seleccione el modo !. • Seleccione el modo de grabación.
Carga de archivos a sitios Web Activación del modo de carga Tras la grabación se puede cargar rápidamente el archivo a sitios Web creados para compartir vídeos (YouTube™). Preparativos: • Seleccione el modo !. • Seleccione el modo de grabación. Pulse UPLOAD dos veces. Si graba un archivo con el modo de carga activado, la grabación se detiene automáticamente 10 minutos después de su inicio. El tiempo restante se muestra en la pantalla LCD.
INFORMACIÓN ADICIONAL Cambio de las configuraciones de menús 1 2 3 Toque MENU. Seleccione el menú que desee. Para volver a la pantalla anterior Seleccione @. Para salir de la pantalla Seleccione [SALIR]. Seleccione el ajuste que desee. Solución de problemas Antes de solicitar asistencia técnica, consulte la siguiente tabla. Si las soluciones indicadas en la tabla no ayudan a solucionar el problema, póngase en contacto con el distribuidor JVC o servicio técnico JVC más cercano para obtener ayuda.
Solución de problemas (continuación) Problema Grabación La grabación no puede realizarse. Aparecen líneas verticales en las imágenes grabadas. Reproducción El vídeo o el sonido se interrumpe. Acción • Deslice el interruptor de modo para seleccionar el modo deseado (! o #). • Este fenómeno se produce al filmar un sujeto iluminado por una luz muy brillante. Esto no es un fallo de funcionamiento. • A veces la reproducción se interrumpe en el cambio de una escena a otra.
Indicaciones de advertencia Indicación Acción ¡AJUSTE FECHA/HORA! • Ajuste el reloj. Si sigue apareciendo el mensaje tras ajustar el reloj, significa que se ha agotado la pila del reloj. Consulte con su distribuidor JVC más próximo. ERROR DE COMUNICACIÓN • Asegúrese de utilizar baterías JVC. NO SE PUEDE UTILIZAR EN MODO DE VÍDEO NO FORMATEADO ¡ERROR DE FORMATEO! ERROR ELIMIN.
Especificaciones Generalidades Fuente de alimentación eléctrica CC 11 V (con adaptador de CA) CC 7,2 V (con batería) Consumo eléctrico Aprox. 3,5 W* * Cuando la luz LED está apagada y la luz de fondo de la pantalla está ajustada en modo [ESTÁNDAR]. Consumo de corriente nominal: 1 A Dimensiones (anchura x altura x fondo) 53 mm x 68 mm x 113 mm Peso Aprox. 325 g Aprox.
h: hora/m: minuto Tiempo de grabación aproximado (para vídeo) Soporte de grabación Unidad de disco duro Tarjeta microSD GZ-HD300 60 GB GZ-HD320 120 GB 4 GB 8 GB UXP 5 h 30 m 11 h 20 m 40 m XP 7 h 30 m 15 h 30 m 1 h 00 m SP 10 h 21 h 44 m 1 h 28 m EP 25 h 50 h 1 h 40 m 3 h 20 m Calidad Número aproximado de imágenes (para imágenes fijas) La unidad de disco duro puede grabar hasta 9999 imágenes fijas en cualquiera de los dos modos.
Precauciones ATENCIÓN: Adaptador de CA Si utiliza el adaptador de CA en países fuera de los EE.UU. El adaptador de CA suministrado tiene una función de selección automática de tensión en la escala de corriente alterna de 110 V a 240 V. USO DEL ENCHUFE ADAPTADOR DE CA En caso de conectar el cable de alimentación de la unidad a un tomacorriente de CA que no sea de la serie American National Standard C73, emplee un enchufe adaptador de CA, denominado “Siemens Plug”, como el mostrado.
Equipo principal • Por seguridad, NO DEBE ... abrir el chasis de la cámara. ... desmontar o modificar el equipo. ... permitir que productos inflamables, agua u objetos metálicos entren en el equipo. ... extraer la batería ni desconectar el suministro de energía con el aparato encendido. ... dejar la batería colocada cuando la cámara no se utilice. ... colocar sobre el aparato ninguna fuente de llama sin protección, tales como velas encendidas. ... exponer el equipo a goteos o salpicaduras. ...
Términos A B C D E G H I Adaptador de CA . ........................................15, 42 Ajuste de la fecha/hora ........................................5 Ajuste del idioma . ............................................16 Ajuste del reloj . ..................................................15 Batería . ........................................................15, 42 Cable USB ...................................................27, 31 Carga de archivos ..............................................