CAMÉSCOPE GZ-R315 GZ-R310 Manuel d’utilisation C5B5_R315_EU_FR
Table des matières Démarrer Vérifier les accessoires ............................................................ 3 Allumez cet appareil ................................................................ 4 Ouverture du couvercle de la borne (couvercle de la carte SD) .............................................................................................. 4 Chargement ............................................................................. 5 Réinitialisation de cet appareil .........................
Démarrer Vérifier les accessoires Si l’un des éléments est manquant ou défectueux, consultez votre revendeur JVC ou le centre de services JVC le plus proche. Illustration Description Adaptateur secteur AC-V10E 0 Charge cet appareil. Fixer le câble de l’adaptateur de charge à l’extrémité du cordon. Il peut également être utilisé pour l’enregistrement ou la lecture de vidéos à l’intérieur. .
Démarrer Allumez cet appareil Ouvrez l’écran LCD pour allumer cet appareil. Pour couper l’alimentation, fermer l’écran LCD. o Pour mettre sous tension Ouverture du couvercle de la borne (couvercle de la carte SD) o Pour ouvrir Ouvrez l’écran LCD. . A Ouvrez l’écran LCD. B Faites glisser vers le bas le verrouillage du couvercle et faites glisser le couvercle sur le côté. C Soulevez doucement le couvercle. . o Pour couper l’alimentation Fermez l’écran LCD. o Pour fermer .
Démarrer Chargement Cet appareil est équipé d’une batterie intégrée. Ouvrez le couvercle du connecteur et connectez l’adaptateur secteur pour charger comme indiqué sur la figure. Réinitialisation de cet appareil Lorsqu’un dysfonctionnement survient sur cet appareil, réinitialisez-le de la manière suivante. (La réinitialisation de l’appareil n’efface pas les données enregistrées.) 1 Ouvrez le couvercle de la borne. 0 Retirez le cordon d’alimentation et tous les câbles de connexion.
Démarrer Quad Proof Avant d’utiliser sous l’eau ou à basse température La conception de cet appareil le rend étanche à l’eau et à la poussière, résistant aux chutes et à l’épreuve du gel. “Précautions relatives à l’utilisation sous l’eau” (A p. 6) “Entretien après utilisation” (A p. 7) “Précautions relatives à l’utilisation à basse température” (A p. 7) “Précautions relatives à l’utilisation à basse température” (A p. 7) .
Démarrer Entretien après utilisation Autres précautions Après avoir utilisé la caméra sous l’eau ou dans des endroits poussiéreux, rincez-la immédiatement et séchez-la complètement. 0 1 Assurez-vous que le couvercle de borne est fermé. 2 Rincez à l’eau propre. Trempez la caméra dans un récipient rempli avec suffisamment d’eau pour l’immerger complètement et rincez-la doucement.
Démarrer Ajustement de la dragonne Fixer le filtre du noyau Fixez un noyau de filtre au câble AV qui est connecté à cet appareil. Le filtre à noyau de ferrite diminue l’interférence lorsque cet appareil est connecté à d’autres dispositifs. . A Ouvrez la tablette B Ajustez la longueur de la dragonne C Fermez la tablette Attention : 0 8 Assurez-vous de bien attacher la dragonne. Si la dragonne est trop desserrée, l’appareil peut tomber et provoquer des blessures ou des dégâts. .
Démarrer Insérer une nouvelle carte SD Insérez une carte SD disponible dans le commerce avant tout enregistrement. “Types de cartes SD utilisables” (A p. 9) “Durée d’enregistrement vidéo approximative” (A p. 46) 1 Retirer la carte Poussez la carte SD vers l’intérieur puis tirez-la vers vous. Ouvrez le couvercle de la borne. . Types de cartes SD utilisables . 2 Fermez l’écran LCD pour éteindre l’appareil. 3 Insérez une carte SD. Les cartes SD suivantes peuvent être utilisées sur cet appareil.
Démarrer Remarque : 0 0 0 0 0 0 0 0 0 0 0 Toute utilisation de cartes SD (y compris des cartes SDHC/SDXC) autres que celles indiquées ci-dessus risque de causer des problèmes lors de l’enregistrement ou la perte de données. L’appareil n’est pas garanti pour fonctionner avec toutes les cartes SD. Il est possible que certaines cartes SD ne fonctionnent pas en raison de changements des spécifications, etc. N’utilisez pas une carte miniSD ou microSD (même si la carte est insérée dans un adaptateur).
Démarrer Utiliser l’écran tactile Verrouillage de l’écran (lors d’une prise de vue sous l’eau) L’écran LCD de cet appareil est un écran tactile qui permet les opérations en touchant l’écran. Les boutons icônes de fonctionnement, des miniatures et des éléments de menu sont affichés sur l’écran tactile en fonction du mode d’utilisation. 0 Il y a deux façons d’utiliser l’écran tactile, à savoir “taper” et “tirer”. Voici quelques exemples ci-dessous.
Démarrer Ajuster le panneau tactile 6 Tapez “OK”. Ajuste la position de réponse des touches sur l’écran tactile. 1 Appuyez sur “MENU”. . 0 . 2 Tapez “CONFIG.”. Le paramétrage se termine et retourne à l’écran de menu. Attention : 0 Ne tapez pas sur les zones autres que la marque “+” pendant l’ajustement de l’écran tactile (étapes 4 - 5). Cela risquerait de provoquer un mauvais fonctionnement de l’écran tactile. Remarque : 0 0 . 3 Tapez “AJUST. ECRAN TACTILE”. .
Démarrer Noms des touches et fonctions sur l’écran LCD Écran de lecture (vidéo) Les écrans suivants s’affichent pendant les modes vidéo A et photo B, et fonctionnent comme des écrans tactiles. Écran d’enregistrement (vidéo/photo) . 0 . 1 0 2 1 Touche Mode A/B (Vidéo/Photo) Bascule entre les modes vidéo A et photo B. 2 Touche Zoom Touche Enregistrement des photos 0 Enregistre des photos pendant l’enregistrement vidéo. “Capturer des photos lors d’un enregistrement vidéo” (A p.
Démarrer Écran de lecture (photo) Affichage Écran d’index (affichage miniature) . 0 Lorsque cet appareil n’est pas utilisé, les boutons de fonctionnement de l’écran LCD disparaissent automatiquement. Tapez sur l’écran pour afficher les touches d’opération à nouveau. 1 Touche Mode A/B (Vidéo/Photo) 0 2 3 Bascule vers un mode d’enregistrement. Touche Écran d’index (affichage miniature) Revient à l’écran d’index (affichage miniature). “Touches de fonctionnement pour la lecture de photos” (A p.
Démarrer Écran Menu (mode enregistrement) Écran Menu (mode lecture) . 1 Touche SILENCE . 1 “Utiliser le mode Silencieux” (A p. 23) 2 Touche INFO. “Utiliser le mode Silencieux” (A p. 23) 2 “Vérifier le temps d’enregistrement restant” (A p. 45) 3 REGLAGE ENREGISTR. Menu REGLAGES CONNEXION Menu 3 CONFIG. Menu 4 Touche Fermer CONFIG. Menu “CONFIG. (vidéo/photo)” (A p. 87) 5 “CONFIG. (vidéo/photo)” (A p. 87) 6 REGLAGE LECTURE Menu “REGLAGE LECTURE Menu (vidéo)” (A p.
Démarrer Régler l’horloge L’écran “REGLER DATE/HEURE !” apparaît lorsque vous allumez cet appareil pour la première fois après l’achat, lorsqu’il n’a pas été utilisé pendant une longue période ou lorsque l’horloge n’a pas encore été réglée. Réglez l’horloge avant tout enregistrement. 1 Réinitialiser l’horloge Réglez l’horloge avec “DATE & HEURE” dans le menu. 1 Appuyez sur “MENU”. Ouvrez l’écran LCD. . . 0 0 2 2 Tapez “CONFIG.”. L’unité s’allume. Lorsque l’écran LCD est fermé, l’unité s’éteint.
Démarrer 7 Sélectionnez votre région puis appuyez sur “ENREG.”. Modification de la langue d’affichage Vous pouvez modifier la langue de l’affichage sur l’écran. 1 Appuyez sur “MENU”. . 0 0 Le décalage horaire entre la ville sélectionnée et l’heure GMT (Temps universel coordonné) est affiché. Tapez sur 0 ou 1 pour régler le nom de la ville. . 2 Tapez “CONFIG.”. . 3 Appuyez sur “LANGUAGE”. . 0 4 Tapez 3 ou 2 pour faire défiler l’écran. Appuyez sur la langue désirée. .
Démarrer Tenir cet appareil Lorsque vous tenez l’appareil, gardez vos coudes près de vous pour éviter que la caméra ne bouge. Montage sur trépied Cet appareil peut être monté sur un trépied (ou un monopode). Ceci est très utile pour empêcher la caméra de bouger et pour vous permettre d’enregistrer à partir d’un endroit fixé. . 0 Pour éviter que l’appareil ne tombe, vérifiez les orifices de vis et les orifices de montage du trépied sur celui-ci avant le montage.
Démarrer Utilisation de l’appareil à l’étranger La forme de la prise de courant varie en fonction des pays et des régions. Pour charger la batterie, vous avez besoin d’une prise convertisseur adaptée à la forme de la prise. “Charger la batterie à l’étranger” (A p. 19) Réglez l’heure et la date à l’heure locale en sélectionnant votre destination de voyage via “REGLAGE ZONE” de “DATE & HEURE”. “Régler l’horloge à l’heure locale lors de vos voyages” (A p.
Démarrer Régler l’heure d’été Lorsque “MARCHE” est sélectionné dans “REGLAGE HEURE ETE” dans “DATE & HEURE”, l’heure est avancée d’1 heure. 1 Appuyez sur “MENU”. Accessoires en option Nom du produit Mini câble HDMI 0 VX-HD310 0 VX-HD315 Remarque : 2 Tapez “CONFIG.”. . 3 Appuyez sur “DATE & HEURE”. . 0 Tapez 3 ou 2 pour faire défiler l’écran. 4 Tapez sur “REGLAGE HEURE ETE”. 5 Tapez sur “MARCHE”. . .
Enregistrement Enregistrer des vidéos en mode automatique Indications apparaissant à l’écran pour l’enregistrement de vidéos Vous pouvez enregistrer sans avoir à vous préoccuper des détails de réglage en utilisant le mode Auto Intelligent P. Les réglages comme l’exposition et la mise au point seront ajustés automatiquement pour s’adapter aux conditions de prises de vue. 0 Dans le cas de prises de vue spécifiques comme une personne etc. son icône est affichée à l’écran.
Enregistrement o Scènes d’auto intelligent Icône d’affichage Touches de fonctionnement pour l’enregistrement vidéo Description g Capture la peau d’une personne de façon extraordinaire. V Permets de capturer des personnes naturellement. f Enregistrer un groupe de personnes avec les réglages les plus appropriés. S Enregistre tout en faisant une mise au point sur un objet à proximité. a Effectue la mise au point à une distance éloignée et capture une image nette avec des couleurs chatoyantes.
Enregistrement Utiliser le mode Silencieux Réglages utiles pour l’enregistrement Lorsque le mode Silencieux est utilisé, l’écran LCD diminue son éclairage et les sons de fonctionnement ne seront pas produits. Utilisez ce mode Silencieux pour enregistrer tranquillement dans des endroits sombres, comme durant un spectacle. 0 T apparaît lorsque “MODE SILENCIEUX” est réglé sur “MARCHE”.
Enregistrement Capturer des photos lors d’un enregistrement vidéo Des photos peuvent être prises en touchant le bouton A avec le mode vidéo (veille ou enregistrement). Capturer des photos en mode Auto Vous pouvez enregistrer sans avoir à vous préoccuper des détails de réglage en utilisant le mode Auto Intelligent P. 1 Ouvrez l’écran LCD. . 0 “PHOTO” apparaît à l’écran lorsqu’une photo est capturée. . Remarque : 0 0 La taille de la photo capturée en mode vidéo est de 1 920 x 1 080.
Enregistrement Indications apparaissant à l’écran lors de l’enregistrement d’une photo . 0 o Scènes d’auto intelligent Icône d’affichage g Capture la peau d’une personne de façon extraordinaire. V Permets de capturer des personnes naturellement. f Enregistrer un groupe de personnes avec les réglages les plus appropriés. S Enregistre tout en faisant une mise au point sur un objet à proximité.
Enregistrement Touches de fonctionnement pour l’enregistrement de photos Utiliser le mode Silencieux Lorsque le mode Silencieux est utilisé, l’écran LCD diminue son éclairage et les sons de fonctionnement ne seront pas produits. Utilisez ce mode Silencieux pour enregistrer tranquillement dans des endroits sombres, comme durant un spectacle. 0 T apparaît lorsque “MODE SILENCIEUX” est réglé sur “MARCHE”.
Enregistrement Effectuer un zoom L’angle de de vue peut être ajusté au moyen du zoom. 0 Utilisez l’embout W (Grand angle) pour effectuer une prise de vue grand angle. 0 Utilisez l’embout T (Téléobjectif) pour grossir le sujet lors de la prise de vue. . 0 0 0 Les options de zoom suivantes sont disponibles : - Zoom optique (1 - 40x) - Zoom dynamique (41 - 60x) - Zoom numérique (41 - 200x) Vous pouvez également utiliser la touche zoom (WT) sur l’écran tactile pour zoomer.
Enregistrement Enregistrement manuel 4 Tapez “REGLAGE ENREGISTR.”. Vous pouvez ajuster les réglages, tels que la luminosité en utilisant le mode Manuel. L’enregistrement Manuel peut être à la fois défini pour les modes vidéo et photo. 1 Ouvrez l’écran LCD. . 5 Tapez sur l’article à régler manuellement. . 0 0 2 Réglez le mode d’enregistrement soit sur A vidéo ou sur B photo.
Enregistrement Ajuster manuellement la mise en point (FOCUS) Procédez à ce réglage si la mise au point n’est pas claire en mode Auto Intelligent ou lorsque vous souhaitez effectuer manuellement la mise au point. 1 Sélectionnez le mode d’enregistrement Manuel. . 6 Ajustez la mise au point. . 0 Si le mode est sur P Auto Intelligent, tapez sur P sur l’écran d’enregistrement pour afficher l’écran de commutation de mode. Tapez sur H pour basculer le mode d’enregistrement en mode manuel. .
Enregistrement Ajuster la luminosité 5 Appuyez sur “MANUEL”. 6 Ajustez la valeur de luminosité. Vous pouvez régler la luminosité à votre niveau préféré. 1 Sélectionnez le mode d’enregistrement Manuel. . . 0 Si le mode est sur P Auto Intelligent, tapez sur P sur l’écran d’enregistrement pour afficher l’écran de commutation de mode. Tapez sur H pour basculer le mode d’enregistrement en mode manuel. . 0 0 0 7 Plage de compensation : -2,0 à +2,0 Tapez sur 3 pour augmenter la luminosité.
Enregistrement Régler la compensation de contre-jour 5 Tapez “MARCHE” ou “AVANCE”. Vous pouvez corriger l’image lorsque le sujet paraît trop sombre en raison du contre-jour. 1 Sélectionnez le mode d’enregistrement Manuel. . 0 . 0 Si le mode est sur P Auto Intelligent, tapez sur P sur l’écran d’enregistrement pour afficher l’écran de commutation de mode. Tapez sur H pour basculer le mode d’enregistrement en mode manuel.
Enregistrement Régler la balance des blancs 5 Sélectionnez le réglage de balance des blancs. Vous pouvez régler la tonalité de couleur afin de bien capturer la source de lumière. 1 Sélectionnez le mode d’enregistrement Manuel. . 0 Vous pouvez toucher l’icône ou sélectionner l’élément à l’aide du bouton “0” “1” et toucher “REGLER”. 0 L’icône de la balance des blancs apparaît sur l’écran une fois le réglage terminé. .
Enregistrement Effectuer des prises de vue en gros plan (TELE MACRO) 4 Appuyez sur “TELE MACRO”. La fonction téléobjectif macro vous permet de prendre un objet en gros plan. . . * L’image n’est qu’une impression. 1 0 0 Sélectionnez le mode d’enregistrement Manuel. 5 Appuyez sur L pour sortir du menu. Appuyez sur J pour retourner à l’écran précédent. Tapez “MARCHE”. . 0 Si le mode est sur P Auto Intelligent, tapez sur P sur l’écran d’enregistrement pour afficher l’écran de commutation de mode.
Enregistrement Prise de vue sous l’eau Verrouillage de l’écran Effectuez les réglages suivants pour la prise de vue sous l’eau. 1 Appuyez sur “MENU”. Réglage de la balance des blancs en mode sous l’eau Corrige les couleurs lors de la prise de vue sous l’eau pour enregistrer des images plus naturelles. Sélectionnez parmi les deux réglages suivants en fonction de la couleur de l’eau à l’endroit de la prise de vue. 1 Appuyez sur “MENU”. . 0 2 Le menu principal s’affiche. Tapez “REGLAGE ENREGISTR.”.
Enregistrement o Pour annuler “VERROUILLER L'ECRAN” Touchez le bouton L. Enregistrer avec des effets Vous pouvez ajouter et enregistrer différents effets sur les vidéos ou les photos. Une fois le réglage effectué, vous pouvez facilement enregistrer des images qui sont adaptées à chaque image. Type d’effet MONOCHROME GRANULEUX Capture des images monochromes rappelant un film en augmentant le contraste de la luminosité à niveau moyen et en accentuant l’effet granuleux rugueux sur l’image.
Enregistrement Enregistrement d’images semblables à une ancienne photo en noir et blanc (MONOCHROME GRANULEUX) 5 Appuyez sur “MONOCHROME GRANULEUX”. Capture des images monochromes rappelant un film en augmentant le contraste de la luminosité à niveau moyen et en accentuant l’effet granuleux rugueux sur l’image. 1 Ouvrez l’écran LCD. . 0 0 6 Lancez l’enregistrement. 0 . 0 0 2 Réglez le mode d’enregistrement soit sur A vidéo ou sur B photo.
Enregistrement Enregistrement d’images de nourriture (NOURRITURE) 5 Appuyez sur “NOURRITURE”. Capture les images des aliments en rendant la nourriture appétissante même sous un éclairage fluorescent, en modifiant les couleurs pour les rendre plus chaudes et plus profondes. 1 Ouvrez l’écran LCD. . 0 0 6 Appuyez sur L pour sortir du menu. Appuyez sur J pour retourner à l’écran précédent. Lancez l’enregistrement.
Enregistrement Enregistrement d’images d’un bébé (BEBE) 5 Appuyez sur “BEBE”. Capture une image régulière et agréable en éclairant le grain de la peau tout en préservant sa teinte rougeâtre, améliorant l’effet d’embellissement de la peau tout en lissant l’aspect de la peau. 1 Ouvrez l’écran LCD. . 0 0 6 Lancez l’enregistrement. 0 . 0 0 2 Réglez le mode d’enregistrement soit sur A vidéo ou sur B photo.
Enregistrement Capturer des sujets clairement (TOUCHE PRIOR. AE/AF) 5 Appuyez sur le réglage désiré. “TOUCHE PRIOR. AE/AF” est une fonction qui ajuste la mise au point et la luminosité selon une zone touchée. Cette fonction est disponible à la fois pour les vidéos et les photos. 1 Ouvrez l’écran LCD. . . 0 . 0 0 2 Réglez le mode d’enregistrement soit sur A vidéo ou sur B photo.
Enregistrement Remarque : 0 0 0 0 0 0 Lorsque “TOUCHE PRIOR. AE/AF” est réglé, “MISE AU POINT” sera réglé sur“AUTO” automatiquement. Tapez sur la position choisie (visage/couleur/région) à nouveau pour annuler le réglage. Tapez sur une position déselectionnée ((face / couleur / région) pour réinitialiser. Si la caméra perd le suivi d’un sujet, tapez à nouveau sur le sujet. Les réglages sont annulés lorsque le zoom est utilisé.
Enregistrement Réglage Détails b ARRET Désactive le stabilisateur d’image. a MARCHE Réduit les secousses de la caméra dans des conditions de prise de vue normales. r MARCHE (AIS) Réduit les secousses de la caméra avec plus d’efficacité pendant les prises de vue grand angle. Uniquement sur l’extrémité grand angle (environ 5x). s (AIS perfectionné) Enregistrer par intervalles (ENREG.
Enregistrement 5 Tapez pour sélectionner un intervalle d’enregistrement (1 à 80 secondes). Régler la prise de vue accélérée Plus le nombre de secondes est important, plus l’intervalle d’enregistrement sera long. Réglage ARRET Désactive la fonction. INTERVALLE 1 S. Permet de prendre un cadre à 1 secondes d’intervalle. Les vidéos enregistrées seront lues à une vitesse 30x. INTERVALLE 5 S. Permet de prendre un cadre à 5 secondes d’intervalle. Les vidéos enregistrées seront lues à une vitesse 150x.
Enregistrement Prendre des photos de groupe (Retardateur) 4 Appuyez sur “RETARDATEUR”. Le retardateur à 10 secondes est une fonction utile pour prendre des photos de groupes. Le retardateur à 2 secondes est utile pour éviter les secousses de la caméra causées en appuyant sur la touche de l’obturateur. Remarque : Cette fonction est disponible en mode d’enregistrement de photo. Pour prendre une photo avec la fonction retardateur, il est recommandé d’utiliser un trépied. “Montage sur trépied” (A p.
Enregistrement Enregistrer des vidéos avec la date et l’heure 5 Sélectionnez le type d’horloge avec 0 ou 1, et tapez sur “REGLER”. Vous pouvez enregistrer des vidéos ensemble avec la date et l’heure. Réglez cette fonction lorsque vous voulez sauvegarder le fichier avec l’affichage de la date et de l’heure. (L’affichage de la date et de l’heure ne peut pas être effacé après l’enregistrement.) 1 Ouvrez l’écran LCD. .
Enregistrement Vérifier le temps d’enregistrement restant Affichez la charge restante de la batterie et le temps d’enregistrement restant. Remarque : 0 0 0 1 La charge restante de la batterie et la durée d’enregistrement restante sont approximatives. La durée d’enregistrement restante s’affiche uniquement en mode vidéo. La durée d’enregistrement restante s’affiche pour le support d’enregistrement actuellement sélectionné. Ouvrez l’écran LCD. . 0 2 Vérifiez que la caméra est en mode d’enregistrement.
Enregistrement Durée d’enregistrement vidéo approximative Qualité d’image Carte SDHC/SDXC 4 Go 8 Go 16 Go 32 Go 64 Go 128 Go UXP 20 m 40 m 1 h 20 m 2 h 40 m 5 h 40 m 11 h 30 m XP 30 m 1h 1 h 50 m 3 h 50 m 8 h 10 m 16 h 20 m EP 1 h 40 m 3 h 30 m 7h 14 h 28 h 50 m 57 h 50 m 0 La durée d’enregistrement est juste indicative. La durée d’enregistrement réelle peut être plus longue ou plus courte que la durée indiquée ci-dessus.
Lecture Lire des vidéos Attention : Ce qui suit sont les types de lectures qui peuvent être effectuées par cette unité. Élément Description Lecture normale Lit les vidéos enregistrées. LECTURE RESUMEE À partir des vidéos enregistrées, les scènes sont extraites automatiquement, et compilées pour une lecture du résumé de la longueur précisée. Commencez la lecture à partir de “LECTURE RESUMEE” dans le menu “REGLAGE LECTURE”.
Lecture Lecture normale Lit les vidéos enregistrées. 1 Ouvrez l’écran LCD. Touches de fonctionnement pour la lecture de vidéos Pendant l’affichage de l’écran d’index . Affichage . 0 0 2 Vérifiez si le mode d’enregistrement est bien A. Si le mode est B photo, tapez B sur l’écran d’enregistrement pour afficher l’écran de basculement de mode. Tapez A pour basculer le mode sur vidéo. Tapez sur M pour sélectionner le mode de lecture.
Lecture Pendant la lecture vidéo Affichage Description J Touche Affichage Fait basculer l’écran entre plein (m) et simple (n) à chaque pression de la touche. 0 Écran simple : certains écrans disparaissent automatiquement lorsque l’écran n’est pas utilisé. 0 Plein écran : Affiche tout. La touche d’affichage passe de n à m. 0 Lorsque l’alimentation est coupée, le réglage de l’affichage revient à l’affichage simple (n). K 3 Bascule vers un mode d’enregistrement.
Lecture Vérifier la date d’enregistrement et d’autres informations Vous pouvez voir l’information d’enregistrement des vidéos enregistrées. 1 Ouvrez l’écran LCD. . . 0 2 Tapez sur la touche A ou B pour sélectionner le mode vidéo ou photo. Tapez sur M pour sélectionner le mode de lecture. . 3 Tapez sur le fichier pour commencer la lecture. . 4 Appuyez sur “MENU”. . 5 Appuyez sur C. . Appuyez sur L pour sortir du menu.
Lecture LECTURE RESUMEE 6 Tapez pour sélectionner une date pour la lecture abrégée. Vous pouvez lire un sommaire des vidéos enregistrées (Lecture sommaire). Cette option est utile pour vérifier rapidement le contenu de vos vidéos. 1 Ouvrez l’écran LCD. . 0 0 0 0 7 Après avoir sélectionné une date, tapez sur “SUIVANT”. Lorsque l’on tape sur “TOUS”, la lecture abrégée sera exécutée pour toutes les dates. Appuyez sur L pour sortir du menu. Appuyez sur J pour retourner à l’écran précédent.
Lecture LIRE AUTRE FICHIER 6 Tapez sur le fichier pour commencer la lecture. L’information de gestion d’une vidéo peut être endommagée si l’enregistrement n’est pas effectué correctement, par exemple l’appareil est mis hors tension au milieu de l’enregistrement. Vous pouvez effectuer les opérations suivantes pour lire les vidéos avec une information de gestion défectueuse. 1 Ouvrez l’écran LCD. . “Touches de fonctionnement pour la lecture de vidéos” (A p.
Lecture Lire des photos Vous pouvez sélectionner et lire les photos enregistrées à partir d’un écran d’index (affichage miniature). 1 Touches de fonctionnement pour la lecture de photos Pendant l’affichage de l’écran d’index Ouvrez l’écran LCD. . 0 Les images fixes qui sont enregistrées en continu à haute vitesse ou à vitesse moyenne seront regroupées. Seul le premier fichier enregistré (photo) est affiché et le groupe est affiché avec un cadre vert. Affichage .
Lecture Pendant la lecture de photos Lecture du diaporama Vous pouvez lancer un diaporama pour lire vos photos. Tapez sur I pendant la lecture de photos pour lancer le diaporama. . 0 Lorsque cet appareil n’est pas utilisé, les boutons de fonctionnement de l’écran tactile disparaissent automatiquement. Tapez sur l’écran pour afficher les touches d’opération à nouveau. Affichage Description A Mode vidéo/photo A/B Bascule entre les modes vidéo et photo.
Lecture Raccorder à et visualiser sur un téléviseur Vous pouvez raccorder cet appareil à un téléviseur pour une lecture. La qualité de l’image sur le téléviseur varie selon le type de téléviseur et le câble de connexion. Sélectionnez le connecteur qui convient le mieux à votre téléviseur. 0 Pour plus de détails, consultez le manuel d’utilisation de votre téléviseur. “Connexion par le Mini connecteur HDMI” (A p. 55) “Connexion par le connecteur AV” (A p.
Lecture Remarque : Changez les réglages dans “SORTIE HDMI” selon la connexion. “ SORTIE HDMI ” (A p. 90) 0 0 0 Lorsqu’il est connecté au téléviseur via le câble mini HDMI, les images et les sons peuvent ne pas sortir correctement selon le téléviseur connecté. Dans ce cas, effectuez les opérations suivantes. 1) Débranchez le mini câble HDMI, et rebranchez-le. 2) Éteignez puis rallumez l’appareil.
Lecture Connexion par le connecteur AV Pour lire des vidéos sur un téléviseur, branchez le câble AV (fourni : E3A-0085-00) à la prise AV de cet appareil. 0 Pour plus de détails, consultez le manuel d’utilisation de votre téléviseur. 1 Branchez l’appareil à la TV. Remarque : Pour toute question concernant le téléviseur ou la méthode de branchement, veuillez contacter le fabricant de votre téléviseur.
Éditer Supprimer des fichiers inutiles Supprimez les vidéos et photos inutiles lorsque l’espace du support d’enregistrement est quasiment plein. Cela libère plus d’espace dans les médias d’enregistrement. “Supprimer le fichier actuellement affiché” (A p. 58) “Supprimer les fichiers sélectionnés” (A p. 58) Remarque : Supprimer les fichiers sélectionnés Supprime les fichiers sélectionnés. Attention : 0 1 Les fichiers supprimés ne peuvent être restaurés. Ouvrez l’écran LCD.
Éditer 5 Tapez sur “REGLER”. Protéger des fichiers Protégez les vidéos/photos importantes pour éviter toute suppression accidentelle. “Protéger/Annuler la protection du fichier actuellement affiché” (A p. 59) “Protéger/Diffuser la protection des fichiers sélectionnés” (A p. 60) Attention : 0 Lorsque le support d’enregistrement est formaté, même les fichiers protégés seront supprimés. . 0 6 Si aucun fichier n’est sélectionné, le bouton “REGLER” ne peut pas être actionné.
Éditer Protéger/Diffuser la protection des fichiers sélectionnés 6 Tapez sur les fichiers pour protéger ou annuler la protection de. Protège ou annule la protection des fichiers sélectionnés. 1 Ouvrez l’écran LCD. . . 0 0 2 Tapez A ou B pour sélectionner le mode vidéo ou photo. Tapez B ou A sur l’écran d’enregistrement pour afficher l’écran de basculement de mode. Tapez A pour basculer le mode sur vidéo A. Tapez B pour basculer le mode photo B. 7 0 P apparaît sur les fichiers sélectionnés.
Éditer Capturer une photo pendant la lecture d’une vidéo 5 Touchez le bouton A. Vous pouvez capturer des photos de scènes que vous aimez dans des vidéos enregistrées. 1 Ouvrez l’écran LCD. . Remarque : 0 0 Les photos sont capturées avec une dimension de 1920 x 1080. Les photos capturées sont stockées dans le support duquel la vidéo est lue. . 0 0 Vérifiez si le mode d’enregistrement est bien A.
Éditer Capturer une partie requise dans la vidéo (DÉCOUPAGE) 6 Tapez la vidéo à modifier. Sélectionnez la partie souhaitée de la vidéo et enregistrez-la en tant que nouveau fichier vidéo. 0 La vidéo originale reste à son emplacement existant. 1 Ouvrez l’écran LCD. . 7 Tapez e pour interrompre la lecture à un point désiré, puis tapez sur “A”. . 0 0 2 Vérifiez si le mode d’enregistrement est bien A.
Copier Copier des fichiers sur un disque en se connectant à un enregistreur Blu-ray Vous pouvez copier des vidéos en qualité haute définition en connectant un enregistreur Blu-ray compatible AVCHD à cet appareil via un câble USB. Pour plus de détails sur la création d’un disque, reportez-vous au manuel d’utilisation de votre enregistreur Blu-ray. 0 Cette opération ne peut pas être effectuée si la charge restante de la batterie n’est pas suffisante. Chargez d’abord complètement la batterie.
Copier Copier vers un ordinateur Windows Vous pouvez copier les fichiers vers un ordinateur via le logiciel fourni. Vous pouvez également créer des disques en utilisant le lecteur DVD ou Blu-ray de l’ordinateur. Si le logiciel fourni n’est pas installé, cet appareil est reconnu comme un périphérique de stockage externe lorsqu’il est raccordé. Remarque : Pour enregistrer vos vidéos sur des disques, un lecteur DVD ou Blu-ray enregistrable est requis pour l’ordinateur utilisé.
Copier 3 Cliquez “Properties” sur la barre du bas pour afficher. . 0 Si un icône “Computer” apparaît sur le bureau, faites un clic droit sur l’icône et sélectionnez “Properties” dans le menu pour afficher les informations de votre ordinateur. Windows Vista/Windows 7 1 Cliquez sur le bouton de démarrage. . 2 Faites un clic droit sur Ordinateur. . 3 Cliquez sur “Propriétés”. .
Copier 4 Vérifiez les éléments dans le tableau ci-dessous. . Windows 8/Windows 8.1 Windows Vista/Windows 7 SE Windows 8 64-bits Windows 8 ou Windows 8 Pro (Versions préinstallées, mode bureau uniquement) Windows8.1 64-bits Windows8.1 ou Windows8.
Copier Installer le logiciel fourni (intégré) 6 Vous pouvez afficher les photos enregistrées au format calendrier et les modifier avec le logiciel qui vous a été fourni. 0 Cette opération ne peut pas être effectuée si la charge restante de la batterie n’est pas suffisante. Chargez d’abord complètement la batterie. Effectuez les étapes suivantes sur votre ordinateur. A Affichez “Apps”. (Pour Windows 8) Cliquer sur l’onglet “Search”. (Pour Windows 8.1) Cliquez sur F.
Copier 8 Cliquez sur “Terminer”. 5 Tapez “LECTURE SUR PC”. . 0 . 9 Cliquez sur “FIN”. “Installation du logiciel pour Everio” apparaît sur l’ordinateur. Les opérations doivent être effectuées sur l’ordinateur une fois que l’écran est commuté. 6 Effectuez les étapes suivantes sur votre ordinateur. A Cliquez “Ouvrez le dossier avec les fichiers souhaités” sur la boîte de dialogue de lecture automatique, puis double-cliquez sur “install.exe”.
Copier Remarque : 0 0 Si “Installation du logiciel pour Everio” n’apparaît pas, double-cliquez sur “JVCCAM_APP”, dans “Poste de travail” ou “Ordinateur”, puis doublecliquez sur “install (ou Install.exe)”. Si la boîte de dialoge de lecture automatique apparaît, sélectionnez “Ouvrez le dossier avec les fichiers souhaités” et cliquez sur “OK”. Puis, cliquez sur “install (ou Install.exe)” dans le dossier. 6 Sélectionnez la source du fichier image.
Copier Débranchement de cet appareil de l’ordinateur Organiser les fichiers Une fois la sauvegarde de vos fichiers terminée, organisez-les en ajoutant des étiquettes, telles que “Voyage en famille” ou “Sport”. Cela vous servira non seulement pour créer des disques, mais également pour visualiser les fichiers par la suite. 1 (Windows 7/Windows 8/Windows 8.1) 1 Cliquez sur “Retirer le périphérique en toute sécurité et éjecter le média”. 2 Cliquez sur tout “JVCCAM ~”.
Copier 5 Enregistrez les fichiers sur la liste créée. Enregistrer des vidéos sur des disques Copiez les fichiers arrangés vers les disques via la liste utilisateur. 1 Insérez un nouveau disque dans le lecteur DVD enregistrable de l’ordinateur. 2 Sélectionnez la liste souhaitée. . Identifier une vidéo ou une photo: 0 0 Vous pouvez sélectionner des fichiers en utilisant le menu “SELECT” en haut à droite de l’écran. Vérifiez l’icône de vidéo/photo sur le coin supérieur droit de la miniature. .
Copier 6 Une fois la copie terminée, cliquez sur “OK”. . 72 Remarque : Les différents types de disques suivants peuvent être utilisés avec le logiciel Everio MediaBrowser 4 fourni. DVD-R DVD-R DL (double couche) DVD-RW DVD+R DVD+R DL DVD+RW 0 Les formats suivants sont supportés par le logiciel fourni Everio MediaBrowser 4. AVCHD Vidéo-DVD* * Pour créer des disques vidéo-DVD à l’aide du logiciel fourni, il est nécessaire d’installer le logiciel supplémentaire (logiciel de création vidéoDVD).
Copier Sauvegarde de fichiers sans utiliser le logiciel fourni 6 Copiez les fichiers sur un ordinateur en suivant la méthode suivante. 0 Cette opération ne peut pas être effectuée si la charge restante de la batterie n’est pas suffisante. Chargez d’abord complètement la batterie. 1 Ouvrez le couvercle de la borne. 2 Connectez votre ordinateur à l’aide du câble USB fourni. 0 Avant de connecter le câble, fermez l’écran LCD pour éteindre l’appareil.
Copier Liste de fichiers et de dossiers Les dossiers et les fichiers sont créés sur la carte SD tel qu’illustré ci-dessous. Ils sont uniquement créés lorsque cela est nécessaire. . Attention : 0 Lorsque la caméra et l’ordinateur sont connectés par un câble USB, les supports enregistrés sont en lecture seule.
Copier Copier vers un ordinateur Mac 6 0 Copiez les fichiers sur un ordinateur Mac, en suivant la méthode suivante. Attention : 0 Charger un fichier image sur iPhoto. 0 Cette opération ne peut pas être effectuée si la charge restante de la batterie n’est pas suffisante. Chargez d’abord complètement la batterie. 1 Ouvrez le couvercle de la borne. 2 Connectez votre ordinateur à l’aide du câble USB fourni. 0 Avant de connecter le câble, fermez l’écran LCD pour éteindre l’appareil.
Menu de configuration Se familiariser avec le menu Le menu suivant est disponible sur cet appareil. 0 MENU PRINCIPAL : Menu qui contient tous les éléments spécifiques à l’enregistrement vidéo, enregistrement d’images fixes, lecture vidéo, et modes de lecture d’image respectivement. Fonctionnement du menu principal Vous pouvez configurer différents réglages via le menu. 1 Appuyez sur “MENU”. . 0 0 2 Le menu principal s’affiche. Le menu varie en fonction du mode que vous utilisez.
Menu de configuration REGLAGE ENREGISTR. Menu (vidéo) . MISE AU POINT La mise au point être réglée manuellement. “Ajuster manuellement la mise en point (FOCUS)” (A p. 29) *Affiché seulement en mode d’enregistrement manuel. AJUSTER LUMINOSITE Ajuste la luminosité générale de l’écran. “Ajuster la luminosité” (A p. 30) *Affiché seulement en mode d’enregistrement manuel. COMP. RETROECLAIRAGE Permet de corriger l’image lorsque le sujet paraît sombre en raison du contre-jour.
Menu de configuration FILTRE VENT Réduit le bruit provoqué par le vent. Réglage Détails ARRET Désactive la fonction. MARCHE Active la fonction. AUTO Active la fonction automatiquement. ENREG. ACCELERE Cette fonction permet de capturer les changements de scènes lentements se déroulant sur une longue période d’être montrés à l’intérieur d’un laps de temps court en prenant des clichés à certains intervalles. Cette option est utile notamment pour recréer l’ouverture d’un bourgeon de fleur.
Menu de configuration QUALITE VIDEO Règle la qualité vidéo. Réglage Détails UXP Permet d’enregistrer avec la meilleure qualité d’image possible. XP Permet d’enregistrer en qualité d’image élevée. EP Permet d’effectuer de longs enregistrements. Remarque : 0 0 Réglez sur le mode “UXP” ou “XP” pour enregistrer des scènes à mouvements rapides ou des scènes avec de forts changements de luminosité pour éviter le bruit.
Menu de configuration NIVEAU MICRO Faites les ajustements de façon à ce que “NIVEAU MICRO” ne devienne pas rouge. Réglage Détails ARRET Masque l’affichage du niveau d’entrée du micro. MARCHE Montre l’affichage du niveau d’entrée du micro. REGLAGE NIVEAU MICRO Règle le niveau du microphone. Faites les ajustements de façon à ce que “NIVEAU MICRO” ne devienne pas rouge. Réglage Détails +1 Augmente le niveau d’entrée du microphone. 0 Le niveau d’entrée du microphone n’est pas changé.
Menu de configuration REGLAGE ENREGISTR. Menu (photo) . MISE AU POINT La mise au point être réglée manuellement. “Ajuster manuellement la mise en point (FOCUS)” (A p. 29) *Affiché seulement en mode d’enregistrement manuel. AJUSTER LUMINOSITE Ajuste la luminosité générale de l’écran. “Ajuster la luminosité” (A p. 30) *Affiché seulement en mode d’enregistrement manuel. COMP. RETROECLAIRAGE Permet de corriger l’image lorsque le sujet paraît sombre en raison du contre-jour.
Menu de configuration EFFET ENREGISTREMENT Vous pouvez ajouter et enregistrer différents effets sur les photos. Une fois le réglage effectué, vous pouvez facilement enregistrer des images qui sont adaptées à chaque image. o MONOCHROME GRANULEUX Vous pouvez enregistrer des images avec un effet de photo noir et blanc granuleux. “Enregistrement d’images semblables à une ancienne photo en noir et blanc (MONOCHROME GRANULEUX)” (A p.
Menu de configuration REGLAGE LECTURE Menu (vidéo) . AFFICHER DATE/HEURE Permet d’afficher la date et l’heure de l’enregistrement pendant la lecture vidéo. Réglage Détails ARRET N’affiche pas la date et l’heure pendant la lecture. MARCHE Affiche la date et l’heure pendant la lecture. LECTURE RESUMEE Lit un sommaire des vidéos enregistrées. “ LECTURE RESUMEE ” (A p. 51) LIRE AUTRE FICHIER Lit des vidéos avec des informations de gestion défectueuses. “ LIRE AUTRE FICHIER ” (A p.
Menu de configuration MODIFIER Menu (vidéo) . PROTEGER/ANNULER Protège les fichiers de toute suppression accidentelle. “Protéger/Annuler la protection du fichier actuellement affiché” (A p. 59) “Protéger/Diffuser la protection des fichiers sélectionnés” (A p. 60) AJUSTER Sélectionnez la partie souhaitée de la vidéo et enregistrez-la en tant que nouveau fichier vidéo. La vidéo originale reste à son emplacement existant. “Capturer une partie requise dans la vidéo (DÉCOUPAGE)” (A p.
Menu de configuration REGLAGE LECTURE Menu (photo) . EFFETS DIAPORAMA Définit les effets de transition dans la lecture du diaporama. Réglage Détails DIAPOSITIVE Commute l’écran en glissant de droite à gauche. VOLETS Commute l’écran en le divisant en bandes verticales. DAMIER Commute l’écran en passant par un motif à carreaux. ALEATOIRE Commute l’écran avec un effet aléatoire depuis DIAPOSITIVE, “VOLETS”, et “DAMIER”.
Menu de configuration MODIFIER Menu (photo) . PROTEGER/ANNULER Protège les fichiers de toute suppression accidentelle. “Protéger/Annuler la protection du fichier actuellement affiché” (A p. 59) “Protéger/Diffuser la protection des fichiers sélectionnés” (A p.
Menu de configuration CONFIG. (vidéo/photo) . Mode D'emploi Mobile Affiche le code QR pour accéder au manuel d’utilisateur de portable. . 0 Le site portail apparaît lorsque le code QR a été lu correctement. Sélectionnez le nom du modèle de votre caméra pour afficher son manuel d’utilisateur de portable. Remarque : 0 0 0 Pour lire le code QR, une application appropriée est requise. Entrez l’URL manuellement dans le navigateur internet si le code QR ne peut pas être lu.
Menu de configuration LUMINOSITE MONITEUR Règle la luminosité de l’écran LCD. Réglage Détails AUTO Règle automatiquement la luminosité à “4” en extérieur, et à “3” en intérieur. 4 Éclaircit le rétroéclairage de l’écran sans tenir compte des conditions environnantes. 3 Règle sur la luminosité standard. 2 Diminue le rétroéclairage de l’écran sans tenir compte des conditions environnantes. 1 Réglé sur luminosité faible. Aide à économiser la batterie lorsque l’option est sélectionnée.
Menu de configuration FORMATER LA CARTE SD Supprime tous les fichiers présents sur la carte SD. Réglage Détails FICHIER Supprime tous les fichiers présents sur la carte SD. FICHIER + GESTION NO Supprime tous les fichiers présents sur la carte SD, puis rétablit le nombre de fichiers et de dossiers à “1”. Attention : 0 0 0 Cette option n’est pas disponible si aucune carte SD n’est insérée. Toutes les données de la carte SD seront supprimées lors du formatage.
Menu de configuration REGLAGES CONNEXION (vidéo/photo) . AFFICHER SUR TV Affiche les icônes, ainsi que la date/l’heure sur un écran télé. Réglage Détails ARRET N’affiche ni les icônes, ni la date/l’heure sur l’écran télé. MARCHE Affiche les icônes, ainsi que la date/l’heure sur l’écran télé. SORTIE VIDEO Règle le rapport hauteur/largeur (16:9 ou 4:3) en fonction de la TV raccordée.
Menu de configuration MENU DE CONNEXION USB Ce menu apparaît lorsque l’appareil est connecté à un ordinateur à l’aide d’un câble USB. LECTURE SUR PC 0 Affiche les vidéos enregistrées par cet appareil en utilisant le Everio MediaBrowser 4. “Installer le logiciel fourni (intégré)” (A p. 67) Sauvegarde des vidéos enregistrées par cet appareil sur votre ordinateur sans utiliser le logiciel fourni. “Sauvegarde de fichiers sans utiliser le logiciel fourni” (A p. 73) “Copier vers un ordinateur Mac” (A p.
Noms des pièces Côté droit Côté inférieur . A Haut-parleur B Dragonne Passez votre main dans la dragonne pour tenir fermement l’appareil. “Ajustement de la dragonne” (A p. 8) 0 92 . A Verrouillage du couvercle B Orifice pour trépied “Montage sur trépied” (A p.
Noms des pièces Côté supérieur/gauche/arrière À l’intérieur du couvercle de la borne . A Fente pour carte SD . A Microphone stéréo 0 Attention à ne pas gêner le microphone avec vos doigts lors de l’enregistrement vidéo.
Noms des pièces Écran LCD . A Écran LCD 0 0 Allume ou éteint l’appareil en s’ouvrant et se fermant. Permet de prendre des auto-portraits en faisant pivoter l’écran. . “Utiliser l’écran tactile” (A p. 11) “Noms des touches et fonctions sur l’écran LCD” (A p. 13) Attention : 0 Attention à ne pas compresser l’écran ou à soumettre ce dernier à un impact trop violent. Vous pourriez endommager ou casser l’écran.
Indicateurs sur l’écran LCD Indications concernant l’enregistrement de base Enregistrer des vidéos . A Mode vidéo . A TOUCHE PRIOR. AE/AF “Capturer des sujets clairement (TOUCHE PRIOR. AE/AF)” (A p. 39) B Compensation de contre-jour “Régler la compensation de contre-jour” (A p. 31) C Téléobjectif macro “Effectuer des prises de vue en gros plan (TELE MACRO)” (A p. 33) D BALANCE DES BLANCS “Régler la balance des blancs” (A p. 32) E Heure “Régler l’horloge” (A p.
Indicateurs sur l’écran LCD Enregistrer des photos Lire une vidéo . A Mode vidéo . A Mode photo 0 Bascule entre les modes vidéo et photo. B Taille d’image “ TAILLE IMAGE ” (A p. 82) C Retardateur “Prendre des photos de groupe (Retardateur)” (A p. 43) D Nombre de prises de vue restantes “Vérifier le temps d’enregistrement restant” (A p. 46) E Mise au point F Enregistrement en cours 0 Bascule entre les modes vidéo et photo. B Qualité vidéo “ QUALITE VIDEO ” (A p.
Indicateurs sur l’écran LCD Lire une photo . A Mode photo 0 Bascule entre les modes vidéo et photo. B Numéro du dossier C Numéro du fichier D Date/Heure 0 Affiche la date et l’heure de l’enregistrement. E Supports d’enregistrement F Indicateur de batterie “Vérifier le temps d’enregistrement restant” (A p. 45) G MODE SILENCIEUX “Utiliser le mode Silencieux” (A p. 23) H Sortie 1080p “ SORTIE HDMI ” (A p.
Dépannage Lorsque l’appareil ne fonctionne pas correctement Chargement Impossible de recharger la batterie. Réinitialisation de cet appareil 1 Ouvrez le couvercle de la borne. 0 Retirez le cordon d’alimentation et tous les câbles de connexion. 2 Fermez l’écran LCD pour éteindre l’appareil. 3 Appuyez sur la touche de réinitialisation doucement à l’aide d’un objet à bout pointu. Lorsque la batterie est complètement chargée, le voyant ne s’allume pas.
Dépannage Alimentation Enregistrement Impossible de mettre sous tension. Aucun enregistrement ne peut être effectué. La caméra ne s’allume pas si la charge restante de la batterie est faible. Dans ce cas, chargez la batterie pendant au moins 40 minutes avant de la mettre sous tension. Vérifiez la touche A / B. “Côté supérieur/gauche/arrière” (A p. 93) Définissez le mode d’enregistrement en tapant sur le bouton E sur l’écran. L’enregistrement s’arrête automatiquement.
Dépannage Carte SD Lecture Impossible d’insérer la carte SD. Le son ou la vidéo est interrompu(e). Assurez-vous de ne pas insérer la carte SD dans le mauvais sens. “Insérer une nouvelle carte SD” (A p. 9) N’utilisez pas une carte miniSD ou microSD sur cet appareil (même si la carte est insérée dans un adaptateur). Cela pourrait provoquer un dysfonctionnement. “Types de cartes SD utilisables” (A p. 9) La lecture est parfois interrompue aux sections reliant deux scènes.
Dépannage Éditer/Copier Impossible de supprimer un fichier. Les fichiers (vidéos/photos) qui sont protégés ne peuvent être supprimés. Annulez la protection avant de supprimer un fichier. “Protéger des fichiers” (A p. 59) Ordinateur Impossible de copier des fichiers vers le disque dur de l’ordinateur. Si le logiciel Everio MediaBrowser 4 fourni n’est pas installé, il est possible que certaines fonctions ne fonctionnement pas correctement. “Installer le logiciel fourni (intégré)” (A p.
Dépannage Écran/Image Autres problèmes L’écran LCD est difficile à visualiser. Les touches sur l’écran tactile ne fonctionnent pas. L’écran LCD peut être difficile à visualiser s’il est utilisé dans des endroits très lumineux, par exemple directement au soleil. Tapez sur les touches sur l’écran tactile avec vos doigts. Les touches peuvent ne pas fonctionner si vous les touchez avec vos ongles ou avec des gants. Désactiver “VERROUILLER L'ECRAN”.
Dépannage L’appareil ne fonctionne pas correctement et des messages d’erreur s’affichent. Cette unité est un périphérique contrôlé par micro-ordinateur. Les décharges électrostatiques, les bruits externes et les interférences (provenant d’une TV ou d’une radio par exemple) peuvent empêcher la caméra de fonctionner correctement.
Dépannage CE FICHIER EST PROTEGE Désactivez la fonction “PROTEGER/ANNULER” dans le menu “MODIFIER”. “Protéger des fichiers” (A p. 59) VERIFIER LOQUET DE PROTECTION CARTE Désactivez la protection en écriture de la carte SD. ESPACE DISPO. INSUFFISANT Effacez ou déplacez les fichiers sur un ordinateur ou d’autres périphériques. Remplacez la carte SD par une nouvelle carte. LIMITE MAXIMUM DU NOMBRE DE FICHIERS ATTEINTE A Déplacez les fichiers ou les dossiers vers un ordinateur ou un autre périphérique.
Entretien Entretenez régulièrement cet appareil pour pouvoir l’utiliser longtemps. Attention : 0 Assurez-vous de détacher la batterie et la fiche d’alimentation électrique avant de procéder à toute opération de maintenance. Caméscope 0 0 Essuyez l’appareil avec un chiffon sec et doux pour retirer toute la saleté. Si celui-ci est particulièrement sale, plongez le chiffon dans une solution détergente neutre, puis passez-le sur le caméscope.
Spécifications Caméra Connecteurs Élément Détails Élément Détails Alimentation Avec un adaptateur secteur : CC 5,2 V HDMI Mini connecteur HDMI Consommation 2,2 W (LUMINOSITE MONITEUR : 3 (standard)) 2,4 W (LUMINOSITE MONITEUR : 4 (éclaircir)) Consommation de courant nominal : 1 A Sortie AV Sortie vidéo : 1,0 V (p-p), 75 Ω Sortie Audio : 300 mV (rms), 1 k Ω Dimensions (mm) 60 x 59,5 x 122 (L x H x P : sans la dragonne) USB Micro USB type AB, compatible USB 2.
Spécifications Photo Adaptateur secteur (AC-V10E) Élément Détails Article Détails Format JPEG standard Alimentation CA 100 V à 240 V, 50 Hz/60 Hz Extension .JPG Sortie CC 5,2 V, 1 A Taille d’image (Nombre de pixels d’enregistrement) (Rapport d’aspect 16:9) 1 920 pixels x 1 080 pixels (2M) (Rapport d’aspect 4:3) 3680 pixels x 2760 pixels (10,15M) 1 440 pixels x 1 080 pixels (1,5M) 640 pixels x 480 pixels (0,3M) “Nombre approximatif de photos (unité : nombre de prises de vue)” (A p.
Marques commerciales Marques commerciales 0 0 Les logos AVCHD et AVCHD sont des marques commerciales de Panasonic Corporation et de Sony Corporation. HDMI (High-Definition Multimedia Interface) et le logo HDMI sont soit des marques de commerce déposées, soit des marques de commerce de HDMI Licensing, LLC aux États-Unis et/ou dans d’autres pays. . 0 0 0 0 0 0 0 0 0 Fabriqué sous licence de Dolby Laboratories. Dolby et le symbole double D sont des marques de commerce de Dolby Laboratories.