HD MEMORY CAMERA GZ-R450 Detailed User Guide C5B5_R450_US_EN
Table of Contents Getting Started Verifying the Accessories ........................................................ 3 Turning on this Unit .................................................................. 4 Opening the Terminal Cover (SD Card Cover) ........................ 4 Charging .................................................................................. 5 Resetting this Unit .................................................................... 5 Quad Proof .....................................
Getting Started Verifying the Accessories If any of the items are missing or defective, consult your JVC dealer or the nearest JVC service center. Illustration Description AC Adapter AC-V11U 0 Charges this unit. Attach the charging adapter cable to the tip of the cord. It can also be used when recording or playing back videos indoors. . Charging Adapter Cable QAM1580-001 0 Attach to the tip of the cord of the AC adapter and connect to the USB connector of this unit to charge. .
Getting Started Turning on this Unit Open the LCD monitor to turn on this unit. To turn off the power, close the LCD monitor. Opening the Terminal Cover (SD Card Cover) o To open o To turn on the power Open the LCD monitor. . A Open the LCD monitor. B Slide down the cover lock and slide the cover aside. C Lift the cover slowly. . o To turn off the power o To close Close the LCD monitor. . The POWER/ACCESS lamp goes off and the power is turned off. “POWER/ACCESS (Power/Access) Lamp” (A p. 99) .
Getting Started Charging This unit is equipped with a built-in battery. Open the connector cover, and connect the AC adapter for charging as shown in the figure. Caution : 0 0 0 There are certain specifications for a USB rechargeable device. To charge, use a device with the output voltage of 5 V/1 A or more.
Getting Started Quad Proof Before Using Underwater or under Low Temperature This unit is equipped with Waterproof, Dust-proof, Drop-proof and Freezeproof features. “Cautions on Using Underwater” (A p. 6) “Maintenance after Use” (A p. 7) “Cautions on Using under Low Temperature” (A p. 7) “Cautions on Using under Low Temperature” (A p. 7) . Waterproof: Equivalent to IEC Standard publication 529 IPX8 and IPX6 (30 minutes at depths up to 5 m (16.4 ft)) .
Getting Started Maintenance after Use Other Precautions After using underwater or in dusty places, rinse the camera with water immediately and dry it completely. 0 1 Ensure that the terminal cover is closed. 2 Rinse with clean water. Soak the camera in a container filled with enough water to immerse the camera completely, and rinse it gently.
Getting Started Grip Adjustment . A Open the pad B Adjust the length of the belt C Close the pad Attaching the Core Filter Attaching core filter to the cable of the AC adapter and the AV cable (on the end connected to this unit) can reduce the interference generated when this unit is connected to an external device. 0 Use the small core filter with the power cable, and the large core filter with the AV cable. 0 Do not attach the core filter to the provided adapter cable.
Getting Started Inserting an SD Card When a commercially available SD card is inserted, recordings can still be made to the card without stopping when the remaining recording time on the built-in memory runs out. “Types of Usable SD Card” (A p. 9) “Approximate Video Recording Time” (A p. 49) 1 Removing the Card Push the SD card inward once, then pull it out straight. Open the terminal cover. . Types of Usable SD Card The following SD cards can be used on this unit.
Getting Started Memo : 0 0 0 0 0 0 0 0 0 0 0 0 Using SD cards (including SDHC/SDXC cards) other than those specified above may result in recording failure or data loss. This unit is not guaranteed to operate with all SD cards. Some SD cards may not work due to specification changes, etc. Do not use a miniSD card or microSD card (even if the card is inserted in an adapter). It may cause malfunction.
Getting Started Using the Touch Screen The LCD monitor of this unit is a touch panel which enables operations by touching the screen. Icon operation buttons, thumbnails, and menu items are displayed on the touch screen according to the mode in use. 0 There are two ways to operate the touch screen, namely “tap” and “drag”. The following are some examples. A Tap the displayed button (icon) or thumbnail (file) on the touch screen to make selection.
Getting Started Adjusting the Touch Panel 6 Tap “OK”. Adjusts the response position of the buttons on the touch screen. 1 Tap “MENU”. . 0 . 2 Tap “SETUP”. Setting ends and returns to the menu screen. Caution : 0 Do not tap areas other than the “+” mark during touch screen adjustment (steps 4 - 5). Doing so may cause the touch screen to malfunction. Memo : 0 0 . 3 Tap “TOUCH SCREEN ADJUST”. . 0 4 The touch screen adjustment screen appears. Tap “+”. (3 times in total) .
Getting Started Names of Buttons and Functions on the LCD Monitor Playback Screen (Video) The following screens are displayed during the A video and B still image modes, and operate as touch screens. Recording Screen (Video/Still Image) . 0 . 1 0 2 1 A/B (Video/Still Image) Mode Button Switches between A video and B still image modes. 2 Zoom Button Still Image Recording Button 0 Records still images during video recording. “Capturing Still Images During Video Recording” (A p.
Getting Started Playback Screen (Still Image) Index Screen (Thumbnail Display) Display . 0 When this unit is not operated, the operation buttons on the LCD monitor disappear automatically. Tap on the screen to display the operation buttons again. 1 A/B (Video/Still Image) Mode Button 0 2 3 Switches to the recording mode. Index Screen (Thumbnail Display) Button Returns to the index screen (thumbnail display). “Operation Buttons for Still Image Playback” (A p.
Getting Started Menu screen (recording mode) Menu screen (playback mode) . 1 SILENT Button . 1 “Using the Silent Mode” (A p. 23) 2 INFO. Button “Using the Silent Mode” (A p. 23) 2 “Checking the Remaining Recording Time” (A p. 48) 3 SETUP Menu CONNECTION SETTINGS Menu “CONNECTION SETTINGS (video/still image)” (A p. 96) 5 6 RECORD SETTING Menu INFO. Button (Displayed only after playback) “Checking the Recording Date and Other Information” (A p. 53) 3 “SETUP (video/still image)” (A p.
Getting Started Clock Setting The “SET DATE/TIME!” screen appears when you turn on this unit for the first time after purchase, when it has not been used for a long time, or when the clock is not set yet. Set the clock before recording. 1 Resetting the Clock Set the clock with “DATE & TIME” from the menu. 1 Tap “MENU”. Open the LCD monitor. . 2 . 0 0 2 Tap “SETUP”. The unit turns on. When the LCD monitor is closed, the unit turns off. Tap “OK” when “SET DATE/TIME!” is displayed. .
Getting Started 7 Select the region where you live and tap “SAVE”. Changing the Display Language The language on the display can be changed. 1 Tap “MENU”. . 0 0 Time difference between the selected city and the GMT (Greenwich Mean Time) is displayed. Tap 0 or 1 to select the city name. . 2 Tap “SETUP”. . 3 Tap “LANGUAGE”. . 0 4 Tap 3 or 2 to scroll the screen. Tap to the desired language. . 0 Tap 3 or 2 to scroll the screen.
Getting Started Holding this Unit When holding this unit, keep your elbows close to your sides to prevent camera shake. Tripod Mounting This unit can be mounted on a tripod (or monopod). This is useful for preventing camera shake and recording from the fixed position. . 0 To prevent this unit from falling off, check the tripod mounting screw holes and positioning holes on the unit carefully before mounting, and turn the screws until they are fastened firmly.
Getting Started Using this Unit Overseas The shape of the power outlet varies according to countries and regions. To charge the battery pack, you need a converter plug that matches the shape of the outlet. “Charging the Battery Pack Overseas” (A p. 19) Change the date and time display to the local time by selecting your travel destination in “AREA SETTING” of “DATE & TIME”. “Setting the Clock to Local Time when Traveling” (A p.
Getting Started Setting Daylight Saving Time When “ON” is selected in “DST SETTING” of “DATE & TIME”, the time is set 1 hour ahead. 1 Tap “MENU”. Optional Accessories Product Name HDMI Mini Cable 0 VX-HD310 0 VX-HD315 Memo : . 2 Tap “SETUP”. . 3 Tap “DATE & TIME”. . 0 Tap 3 or 2 to scroll the screen. 4 Tap “DST SETTING”. 5 Tap “ON”. . . Memo : 0 0 What is daylight saving time? Daylight saving time is the system of setting the clock 1 hour ahead for a fixed period in summer.
Recording Taking Videos in Auto Mode Indications for Video Recording You can record without worrying about the setting details by using the P Intelligent Auto mode. Settings such as exposure and focus will be adjusted automatically to suit the shooting conditions. 0 In case of specific shooting scenes such as person etc., its icon is displayed on the screen. 0 Before recording an important scene, it is recommended to conduct a trial recording. 1 Open the LCD monitor. .
Recording o Scenes of Intelligent Auto Display Icon Operation Buttons for Video Recording Description g Captures one’s skin beautifully. V Allows people to be captured naturally. f Record a group of people with the most suitable settings. S Records while focusing on a near object. a Focuses at a far distance and captures a sharp image with vivid colors. Z Records in dark places with minimal noise in the overall image.
Recording Using the Silent Mode Useful Settings for Recording When the Silent mode is used, the LCD monitor darkens and operation sounds will not be output. Use this mode to record quietly in dark places such as during a performance. 0 T appears when “SILENT MODE” is set to “ON”. 0 To mute only the operating sound, set “OPERATION SOUND” in the menu to “OFF” instead of using the silent mode. “ OPERATION SOUND ” (A p.
Recording Memo : 0 0 0 0 0 0 0 0 Check the remaining recording time in the media before you start shooting. If there is not enough space, move (copy) the data to a computer or disc. When there are many files in the media, it may take time for them to be displayed on the playback screen. Wait for a while as the POWER/ ACCESS lamp blinks, indicating normal operation.
Recording Taking Still Images in Auto Mode Indications During Still Image Recording You can record without worrying about the setting details by using the P Intelligent Auto mode. 1 Open the LCD monitor. . 0 Some displays disappear after approximately 3 seconds. Use the n button to change the displays. Display Icon . 0 0 2 Check if the recording mode is B. If the mode is A video, tap A on the recording screen to display the mode switching screen. Tap B to switch the mode to still image.
Recording o Scenes of Intelligent Auto Display Icon Operation Buttons for Still Image Recording Description g Captures one’s skin beautifully. V Allows people to be captured naturally. f Record a group of people with the most suitable settings. S Records while focusing on a near object. a Focuses at a far distance and captures a sharp image with vivid colors. Z Records in dark places with minimal noise in the overall image.
Recording Using the Silent Mode When the Silent mode is used, the LCD monitor darkens and operation sounds will not be output. Use this mode to record quietly in dark places such as during a performance. 0 T appears when “SILENT MODE” is set to “ON”. 0 To mute only the operating sound, set “OPERATION SOUND” in the menu to “OFF” instead of using the silent mode. “ OPERATION SOUND ” (A p. 94) Zooming The angle of view can be adjusted using zoom. Use the W end (wide angle end) to shoot a wider field of view.
Recording Manual Recording 4 Tap “RECORD SETTING”. You can adjust settings, such as brightness, by using the manual mode. Manual recording can be set for both video and still image modes. 1 Open the LCD monitor. . 5 Tap the item to set manually. . 0 0 2 Set the recording mode to either A video or B still image. To switch the mode between video and still image, tap A or B on the recording screen to display the mode switching screen.
Recording Adjusting Focus Manually (FOCUS) 5 Tap “MANUAL”. 6 Adjust the focus. Set this when the focus is not clear in Intelligent Auto or when manual focusing is desired. 1 Select the Manual recording mode. . . 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen. Tap H to switch the recording mode to Manual. . 0 0 . 2 7 Tap E to focus on a distant subject. If E appears blinking, focus cannot be set any further.
Recording Adjusting Brightness 5 Tap “MANUAL”. 6 Adjust the brightness value. You can adjust the brightness to your preferred level. 1 Select the Manual recording mode. . . 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen. Tap H to switch the recording mode to Manual. . 0 0 0 . 2 7 Compensation range: -2.0 to +2.0 Tap 3 to increase the brightness. Tap 2 to decrease the brightness. Tap “SET” to confirm. Tap “MENU”. . .
Recording Setting Backlight Compensation 5 Tap “ON” or “ADVANCE”. You can correct the image when the subject appears too dark due to backlight. 1 Select the Manual recording mode. . 0 . 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen. Tap H to switch the recording mode to Manual. 0 “ADVANCE” is designed to perform more effective backlight compensation. Choose this when the backlight compensation is not adjusted appropriately by “ON”.
Recording Setting White Balance 5 Select the white balance setting. You can set the color tone to suit the light source. 1 Select the Manual recording mode. . 0 0 . 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen. Tap H to switch the recording mode to Manual. You can either tap the icon, or select the item using the “0” “1” button and tap “SET”. The White Balance icon appears on the screen upon completing the setting.
Recording Taking Close-up Shots (TELE MACRO) 4 Tap 1. You can take close-up shots of an object using the tele macro function. . *The image is only an impression. 1 Select the Manual recording mode. . 5 Tap “TELE MACRO”. . . 0 0 0 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen. Tap H to switch the recording mode to Manual. 6 If the icon is not displayed on the screen, tap 1 to scroll the screen. Tap L to exit the menu.
Recording Shooting under Water 5 Tap q or r. Perform the following settings to shoot underwater. Setting the White Balance to Underwater Mode Corrects the color when shooting underwater to record more natural images. Select from the following two settings depending on the color of the water at the shooting location. 1 Select the Manual recording mode. . Setting . 0 If the mode is P Intelligent Auto, tap P on the recording screen to display the mode switching screen.
Recording 4 Tap “SCREEN LOCK”. 0 The L button appears. Recording with Effects You can add and record various effects to videos or still images. Once setting is done, you can easily record images that are suitable for each image. Type of Effect GRAINY MONOCHROME Captures film-like monochrome images by increasing the contrast of mid-level brightness and emphasizing the rough grainy feel on the image. “Recording Images Like an Old Black and White Photo (GRAINY MONOCHROME)” (A p.
Recording Recording Images Like an Old Black and White Photo (GRAINY MONOCHROME) 5 Tap “GRAINY MONOCHROME”. Captures film-like monochrome images by increasing the contrast of midlevel brightness and emphasizing the rough grainy feel on the image. 1 Open the LCD monitor. . 0 0 6 Start recording. 0 . 0 0 2 Set the recording mode to either A video or B still image. To switch the mode between video and still image, tap A or B on the recording screen to display the mode switching screen.
Recording Recording Food Images (FOOD) 5 Tap “FOOD”. Captures food images such that the food looks appetizing even under fluorescent lighting in homes by changing the colors to warm-colors and deepening the colors. 1 Open the LCD monitor. . 0 0 6 Tap L to exit the menu. Tap J to return to the previous screen. Start recording. 0 To cancel the setting, repeat the procedure from the beginning and tap “OFF” in Step 5. . 0 0 2 Set the recording mode to either A video or B still image.
Recording Recording Images of a Baby (BABY) 5 Tap “BABY”. Captures a soft and gentle image by lightening the skin tone while retaining the reddish hue, enhancing the skin beautifying effect as well as smoothing the appearance of the skin. 1 Open the LCD monitor. . 0 0 6 Start recording. 0 . 0 0 2 Set the recording mode to either A video or B still image. To switch the mode between video and still image, tap A or B on the recording screen to display the mode switching screen.
Recording Recording with Animation Effects (ANIMATION EFFECT) 5 Select a desired effect and tap “SET”. You can add animation effects to video recordings. The animation effects appear when smiles are detected or when the screen is touched. 1 Open the LCD monitor. . 0 0 0 0 Tap 0 or 1 to change the effect. Press the START/STOP button the camera to start recording. Press again to stop. To select another effect again after tapping “SET”, tap J. Tap L to exit “ANIMATION EFFECT”.
Recording During Setting After Setting Note Animation (effect) appears when smiles are detected. . . Animation (effect) appears when smiles are detected. . . Animation (effect) appears when smiles are detected. . . Animation (effect) appears when the screen is touched. . 40 .
Recording Capturing Subjects Clearly (TOUCH PRIORITY AE/AF) 5 Tap the desired setting. “TOUCH PRIORITY AE/AF” is a function that adjusts focus and brightness based on a tapped position. By registering the face of a person beforehand, you can enable tracking of the person even without specific selection during recording. This function is available for both videos and still images. 1 Open the LCD monitor. . . 0 0 0 . 0 0 2 Set the recording mode to either A video or B still image.
Recording Memo : 0 0 0 0 0 0 When “TOUCH PRIORITY AE/AF” is set, “FOCUS” will be set to “AUTO” automatically. Tap the selected position (face/color/area) again to cancel the setting. Tap on an unselected position (face/color/area) to reset. If the camera loses track of a subject, tap the subject again. Settings are canceled when zoom operation is performed. (“AREA SELECT” only) When “COLOR TRACKING” is set, the targeted subject (color) may change if similar colors are detected.
Recording Setting Details b OFF Deactivates image stabilizer. a ON Reduces camera shake under normal shooting conditions. r ON (AIS) Reduces camera shake more effectively when shooting bright scenes on the wide angle end. Only on the wide angle end (approx. 5x). s (Enhanced AIS) The area of correction in the enhanced AIS mode is greater than that in the AIS mode. Camera shake can be reduced more effectively even when recording is performed by zooming from wide angle to telephoto.
Recording 5 Tap to select a recording interval (1 to 80 seconds). Time-Lapse Setting The greater the number of seconds, the longer the recording interval. Setting . 0 0 0 0 6 If the icon is not displayed on the screen, tap 1 to scroll the screen. The greater the number of seconds, the longer the recording interval. Tap L to exit the menu. Tap J to return to the previous screen. OFF Deactivates the function. 1SEC INTERVAL Takes a frame at 1-second intervals.
Recording Recording with a Part of the Screen Enlarged in Sub Screen (CLOSE-UP SUB-WINDOW) 5 Select and tap on the position to be displayed in the sub screen. Record with a portion of the screen enlarged and displayed in a sub screen. This allows you to record the surrounding and the expression of the subject at the same time. 1 Open the LCD monitor. . 0 0 6 Tap A to switch the position of sub screen between right and left.
Recording Taking Group Shots (Self-timer) 4 Tap “SELF-TIMER”. The 10-second self-timer is a convenient function for taking group photos. The 2-second self-timer is useful for preventing camera shake caused by pressing the shutter button. Memo : This function is available in still image recording mode. When shooting a photo using the self-timer function, use of a tripod is recommended. “Tripod Mounting” (A p. 18) 0 0 . 0 0 0 Using the 2-/10-second Self-timer 1 Open the LCD monitor.
Recording Recording Videos with Date and Time 5 Select the type of clock with 0 or 1, and tap “SET”. You can record videos together with the date and time. Set this when you want to save the file with date and time display. (The date and time cannot be deleted after recording.) 1 Open the LCD monitor. . 0 0 6 When “SET” is tapped, the precaution for date/time recording appears. Tap L to exit the menu. Tap the display position with your finger and drag your finger to adjust. .
Recording Checking the Remaining Recording Time Display the remaining battery power and the remaining recording time. Memo : 0 0 0 The remaining battery power and the remaining recording time are estimates. The remaining recording time is displayed only during video mode. The remaining recording time is displayed for the recording media that is currently selected. 1 Open the LCD monitor. . 0 2 Check that the camera is set to the recording mode.
Recording Approximate Video Recording Time Picture quality Built-in memory 32GB UXP 2 h 40 m XP 3 h 40 m EP 13 h 30 m 60p 2 h 20 m Picture quality SDHC/SDXC card 4GB 8GB 16GB 32GB 64GB 128GB UXP 20 m 40 m 1 h 20 m 2 h 40 m 5 h 40 m 11 h 30 m XP 30 m 1h 1 h 50 m 3 h 50 m 8 h 10 m 16 h 20 m EP 1 h 40 m 3 h 30 m 7h 14 h 28 h 50 m 57 h 50 m 60p 15 m 35 m 1 h 10 m 2 h 30 m 5h 10 h 10 m 0 0 The recordable time is only a guide.
Playback Playing Back Videos Caution : The followings are the types of playback that can be performed by this unit. Item Description Normal Playback Plays back the recorded videos. DIGEST PLAYBACK From the recorded video, scenes are extracted automatically, pieced together for a digest playback within the specified length. Start playback from “DIGEST PLAYBACK” in the “PLAYBACK SETTING” menu. PLAYBACK OTHER FILE Videos with defective management information can be played back.
Playback Normal Playback Caution : Plays back the recorded videos. 0 1 Open the LCD monitor. 0 While this unit may be used with the LCD monitor reversed and closed, the temperature rises more easily. Do not use this unit with the LCD monitor reversed and closed for long periods of time, or in places exposed to direct sunlight or high temperatures. The power may turn off to protect the circuit if the temperature of this unit rises too much.
Playback During Video Playback Display Description J Display Button Switches the display between full (m) and simple (n) with every tap of the button. 0 Simple display: Some displays disappear automatically when the screen is not operated. 0 Full display: Displays everything. The display button changes from n to m. 0 When the power is turned off, the display setting will revert to simple display (n). K 3 Switches to the recording mode.
Playback Checking the Recording Date and Other Information 5 Tap C. You can see the recording information of the recorded videos. 1 Open the LCD monitor. . Tap L to exit the menu. You can display the recording date and duration of the selected file. 0 . 0 2 Tap A or B to select the video or still image mode. Tap M to select the playback mode. . . 3 Tap on the file to start playback. . 4 Tap “MENU”. .
Playback DIGEST PLAYBACK 6 Tap to select a date for Digest Playback. You can play back a digest of recorded videos (Digest Playback). This is useful for checking the content of videos quickly. 1 Open the LCD monitor. . 0 0 0 0 7 2 Select the Digest Playback time (Only when “AUTO” is selected in Step 7) . 0 0 After selecting a date, tap “NEXT”. When “ALL” is tapped, Digest Playback will be performed for all the dates. Tap L to exit the menu. Tap J to return to the previous screen.
Playback PLAYBACK OTHER FILE 6 Tap on the file to start playback. The management information of a video may be damaged if recording is not performed correctly, such as turning off the power in the middle of recording. You can perform the following operations to play back the videos with defective management information. 1 Open the LCD monitor. . “Operation Buttons for Video Playback” (A p. 51) 0 Tap “L” to return to the usual index screen.
Playback Playing Back Still Images You can select and play back the recorded still images from an index screen (thumbnail display). 1 Operation Buttons for Still Image Playback During Index Screen Display Open the LCD monitor. . 0 Still images that are recorded continuously in high-speed or mediumspeed will be grouped together. Only the first recorded file (still image) is shown and the group is displayed with a green frame. Display . 0 0 2 Check if the recording mode is B.
Playback During Still Image Playback Slideshow Playback Still images can be played back in a slideshow. Tap I during still image playback to start the slideshow. . 0 When this unit is not operated, the operation buttons on the touch screen disappear automatically. Tap on the screen to display the operation buttons again. Display Description A Video/Still Image Mode A/B Switches between video and still image modes.
Playback Connecting to and Viewing on TV You can connect this unit to a TV for playback. The image quality on TV varies with the type of TV and the connecting cable. Select the connector that best suits your TV. 0 Refer also to the instruction manual of the TV in use. “Connecting via the HDMI Mini Connector” (A p. 58) “Connecting via the AV Connector” (A p. 60) Connecting via the HDMI Mini Connector If you are using an HDTV, you can play back in HD quality by connecting to the HDMI mini connector.
Playback Memo : Change the settings in “HDMI OUTPUT” according to the connection. “ HDMI OUTPUT ” (A p. 96) 0 0 0 When connected to the TV via the HDMI mini cable, images and sounds may not be output properly depending on the TV connected. In such cases, perform the following operations. 1) Disconnect the HDMI mini cable and connect it again. 2) Turn off and on this unit again. For questions about the TV or method of connection, contact your TV's manufacturer.
Playback Connecting via the AV Connector To playback videos on TV, connect the AV cable (provided: E3A-0085-00) to the AV terminal of this unit. 0 Refer also to the instruction manual of the TV in use. 1 Connect to a TV. Memo : For questions about the TV or method of connection, contact your TV's manufacturer. 0 AV cable (provided: E3A-0085-00) Wiring specifications (for video/audio) of the 4-pole mini plug are described in the following.
Editing Deleting Unwanted Files Delete unwanted videos and still images when the space in the recording media is running out. Doing so frees up more space in the recording media. “Deleting the Currently Displayed File” (A p. 61) “Deleting Selected Files” (A p. 61) Memo : Deleting Selected Files Deletes the selected files. Caution : 0 1 Deleted files cannot be restored. Open the LCD monitor. Deleted files cannot be restored. Files that are protected cannot be deleted.
Editing 5 Tap “SET”. Protecting Files Prevent important videos/still images from being deleted accidently by protecting them. “Protecting/Releasing Protection of the Currently Displayed File” (A p. 62) “Protecting/Releasing Protection of Selected Files” (A p. 63) Caution : 0 . 0 6 When the recording media is formatted, even the protected files will be deleted. If no file is selected, the “SET” button cannot be pressed. Tap “EXECUTE” to confirm the deletion.
Editing Protecting/Releasing Protection of Selected Files 6 Tap on the files to protect or release protection of. Protects or releases protection of the selected files. 1 Open the LCD monitor. . . 0 0 2 Tap A or B to select the video or still image mode. Tap B or A on the recording screen to display the mode switching screen. Tap A to switch to the video mode A. Tap B to switch to the still image mode B. 7 0 P appears on the selected files. To remove P from a file, tap on the file again.
Editing Capturing a Still Image in the Video During Playback 5 Tap the A button. You can capture still images of the scenes you like in the recorded videos. 1 Open the LCD monitor. . Memo : 0 0 . 0 0 2 Check if the recording mode is A. If the mode is B still image, tap B on the recording screen to display the mode switching screen. Tap A to switch the mode to video. Tap M to select the playback mode. . 3 Tap on the desired video. 4 Tap pause e at the desired scene during playback. . .
Editing Combining Videos Recorded by Seamless Recording 6 Tap “COMBINE SCENES”. Videos that are recorded on two separate media and with “SEAMLESS RECORDING” in the video recording menu enabled can be combined into a single video. “ SEAMLESS RECORDING ” (A p. 84) 1 Open the LCD monitor. . 0 7 This unit starts a search to detect seamless videos. Combining cannot be performed if no seamless videos are found. Tap “YES”. . 0 0 2 Check if the recording mode is A.
Editing Capturing a Required Part in the Video (TRIMMING) 6 Tap the video to edit. Select the required part of a video and save it as a new video file. 0 The original video remains in its existing location. 1 Open the LCD monitor. . 7 Tap e to pause playback at the desired start point, then tap “A”. . 0 0 2 Check if the recording mode is A. If the mode is B still image, tap B on the recording screen to display the mode switching screen. Tap A to switch the mode to video. .
Copying Dubbing Files to a Disc by Connecting to a Blu-ray Recorder 5 Tap the desired media. You can dub videos in the high definition quality by connecting an AVCHDcompliant Blu-ray recorder to this unit via a USB cable. For details on creating the disc, refer to the instruction manual of your Blu-ray recorder. 0 This operation cannot be completed if the remaining battery power is not enough. Charge the battery fully first. 1 Open the terminal cover. 2 Connect to a Blu-ray recorder. .
Copying Copying Files to an SD Card 5 Tap “COPY”. You can copy videos and still images from the built-in memory to SD card. Copying still images to cards makes it convenient to bring them to the shop for printing (developing). 0 This operation cannot be completed if the remaining battery power is not enough. Charge the battery fully first. Caution : 0 0 Make sure that there is enough space left in the destination medium. Videos in the SD card cannot be copied to the built-in memory.
Copying Copying to Windows PC You can copy files to a computer using the provided software. Discs can also be created using the computer’s DVD or Blu-ray drive. If the provided software is not installed, this unit will be recognized as an external storage when connected. Memo : To record to discs, a recordable DVD or Blu-ray drive is required for the computer in use.
Copying 3 Click “Properties” on the bottom bar to display. . 0 If a “Computer” icon is shown on desktop, right-click the icon and select “Properties” in the menu to display your computer information. Windows Vista/Windows 7 1 Click the start button. . 2 Right-click Computer. . 3 Click “Properties”. .
Copying 4 Check the items with the table below. . Windows 8/Windows 8.1 Windows Vista/Windows 7 OS Windows 8 64-bit Windows 8 or Windows 8 Pro (Pre-installed versions, desktop mode only) Windows8.1 64-bit Windows8.1 or Windows8.1 Pro (Pre-installed versions, desktop mode only) Windows Vista 32/64-bit Home Basic or Home Premium (Pre-installed versions only) Service Pack 2 Windows 7 32/64-bit Home Premium (Pre-installed versions only) Service Pack 1 CPU Intel Core Duo, CPU 1.
Copying Installing the Provided Software (Built-in) 6 You can display the recorded images in calendar format and perform editing using the provided software. 0 This operation cannot be completed if the remaining battery power is not enough. Charge the battery fully first. Perform the following operations on your computer. A Display “Apps”. (For Windows 8) Click the “Search” charm. (For Windows 8.1) Click F. Preparations Connect this unit to a computer with a USB cable. o Windows 8/Windows 8.
Copying 8 5 Click “Finish”. Tap “PLAYBACK ON PC”. . 0 . 9 Click “Quit”. “Everio Software Setup” appears on the computer. Operations are to be performed on the computer after the screen switches. 6 Perform the following operations on your computer. A Click “Open folder to view files” on the auto play dialog box, and then double-click “install.exe”. B Click “Yes” on the User Account Control screen. *Windows 7 . 0 Installation is complete, and two icons are created on the desktop.
Copying Memo : 0 0 If “Everio Software Setup” doesn’t appear, double-click “JVCCAM_APP” in “My Computer” or “Computer”, then double-click “install (or Install.exe)”. If the auto play dialog box appears, select “Open folder to view files” and click “OK”. Then, click “install (or Install.exe)” in the folder. 6 Select the source of the image file. Backing Up All Files Before making backup, make sure that enough free space is left in the computer's hard disk (HDD).
Copying Disconnecting this Unit from Computer Organizing Files After backing up your files, organize them by adding labels such as “Family Trip” or “Athletic Meet”. This is useful not only for creating discs, but for viewing the files too. 1 Double-click on the Everio MediaBrowser 4 icon. 0 The provided software starts up. . (Windows 7/Windows 8/Windows 8.1) 1 Click “Safely Remove Hardware and Eject Media”. 2 Click all “JVCCAM~”. 3 Disconnect the USB cable and close the LCD monitor.
Copying 5 Register files to the created user list. Recording Videos to Discs Copy the files that are arranged using the user list to discs. 1 Insert a new disc into the PC’s recordable DVD drive. 2 Select the desired user list. . Identifying Video or Still Image: 0 0 You can select files using the “SELECT” menu on the top right of the screen. Check the video/still image icon on the top right corner of the thumbnail. . 3 Select the disc type. .
Copying 6 After copying is complete, click “OK”. . Memo : The following types of discs can be used on the provided software Everio MediaBrowser 4. DVD-R DVD-R DL DVD-RW DVD+R DVD+R DL DVD+RW 0 The following formats are supported by the provided software Everio MediaBrowser 4. AVCHD DVD-Video* * To create DVD-Video discs using the provided software, it is necessary to install the additional software (software for creating DVD-Video). For details, refer to the Pixela homepage. http://www.pixela.co.
Copying Backing Up Files Without Using Provided Software 6 Copy the files to a computer using the following method. 0 This operation cannot be completed if the remaining battery power is not enough. Charge the battery fully first. 1 Open the terminal cover. 2 Connect to your PC using the provided USB cable. 0 Before connecting the cable, close the LCD monitor to turn off this unit.
Copying List of Files and Folders Folders and files are created in the built-in memory and SD card as shown below. They are created only when necessary. . Caution : 0 When the camera and PC are connected by an USB cable, recorded media are read-only.
Copying Copying to Mac Computer 6 0 Copy the files to a Mac computer using the following method. Caution : 0 0 This operation cannot be completed if the remaining battery power is not enough. Charge the battery fully first. 1 Open the terminal cover. 2 Connect to your PC using the provided USB cable. 0 Load image file to iPhoto. 0 7 Edit the video using iMovie. 0 0 0 Before connecting the cable, close the LCD monitor to turn off this unit.
Settings Menu Operating the Menu The following menu is available on this unit. 0 TOP MENU: Menu that contains all the items specific to the video recording, still image recording, video playback, and still image playback modes respectively. Operating the Top Menu You can configure various settings using the menu. 1 Tap “MENU”. . 0 0 2 The top menu appears. The menu differs according to the mode in use. Tap the desired menu. . 3 Tap the desired setting. .
Settings Menu RECORD SETTING Menu (video) . FOCUS Focus can be adjusted manually. “Adjusting Focus Manually (FOCUS)” (A p. 29) *Displayed only in the manual recording mode. BRIGHTNESS ADJUST Adjusts the overall brightness of the screen. “Adjusting Brightness” (A p. 30) *Displayed only in the manual recording mode. BACKLIGHT COMP. Corrects the image when the subject appears dark due to backlight. “Setting Backlight Compensation” (A p. 31) *Displayed only in the manual recording mode.
Settings Menu GAIN UP Makes the subject appear bright automatically when recording in dark places. Setting Details OFF Deactivates the function. ON Electrically brightens the scene when it is dark. AUTO SLOW-SHUTTER Slows down the shutter speed to brighten the scene when it is dark. Memo : 0 Although “AUTO SLOW-SHUTTER” brightens the scene more than “ON”, movements of the subject may become unnatural. WIND CUT Reduces the noise caused by wind. Setting Details OFF Deactivates the function.
Settings Menu DATE/TIME RECORDING You can record videos together with the date and time. Set this when you want to save the file with date and time display. (The date and time cannot be deleted after recording.) “Recording Videos with Date and Time” (A p. 47) SHUTTER MODE Continuous shooting settings can be adjusted. Setting Details RECORD ONE SHOT Records one still image. CONTINUOUS SHOOTING Records still images continuously while the A button on the LCD screen is tapped.
Settings Menu VIDEO QUALITY Sets the video quality. Setting Details UXP Enables recording in the best picture quality. XP Enables recording in high picture quality. EP Enables long recordings. Memo : 0 0 Set to “UXP” or “XP” mode when recording fast-moving scenes or scenes with extreme changes of brightness to avoid noise. Video quality cannot be set in the 60p mode. ZOOM Sets the maximum zoom ratio. Setting Details 40x OPTICAL Enables recording with 1 - 40x optical zoom.
Settings Menu MIC LEVEL SETTING Sets the microphone level. Make the adjustments such that “MIC LEVEL” does not turn red. Setting Details +1 Increases the microphone input level. 0 The microphone input level is not changed. -1 Decreases the microphone input level. K2 TECHNOLOGY Reduces the degradation of sound quality caused by digital signal processing, and records a sound quality close to the original. Setting Details OFF Deactivates K2 TECHNOLOGY. ON Activates K2 TECHNOLOGY.
Settings Menu RECORD SETTING Menu (still image) . FOCUS Focus can be adjusted manually. “Adjusting Focus Manually (FOCUS)” (A p. 29) *Displayed only in the manual recording mode. BRIGHTNESS ADJUST Adjusts the overall brightness of the screen. “Adjusting Brightness” (A p. 30) *Displayed only in the manual recording mode. BACKLIGHT COMP. Corrects the image when the subject appears dark due to backlight. “Setting Backlight Compensation” (A p. 31) *Displayed only in the manual recording mode.
Settings Menu GAIN UP Makes the subject appear bright automatically when recording in dark places. Setting Details OFF Deactivates the function. ON Electrically brightens the scene when it is dark. Memo : 0 Setting can be adjusted separately for videos. “GAIN UP (Video)” (A p. 83) RECORDING EFFECT You can add and record various effects to the images. Once setting is done, you can easily record images that are suitable for each image.
Settings Menu PLAYBACK SETTING Menu (video) . DISPLAY DATE/TIME Sets whether to display the recording date and time during video playback. Setting Details OFF Does not display the date and time during playback. ON Displays the date and time during playback. DIGEST PLAYBACK Plays back a digest of the recorded videos. “ DIGEST PLAYBACK ” (A p. 54) PLAYBACK OTHER FILE Plays videos with defective management information. “ PLAYBACK OTHER FILE ” (A p.
Settings Menu EDIT Menu (video) . PROTECT/CANCEL Protects files from being deleted accidently. “Protecting/Releasing Protection of the Currently Displayed File” (A p. 62) “Protecting/Releasing Protection of Selected Files” (A p. 63) COPY Copies files from the built-in memory to the SD card. “Copying Files to an SD Card” (A p. 68) TRIMMING Select the required part of a video and save it as a new video file. The original video remains in its existing location.
Settings Menu PLAYBACK SETTING Menu (still image) . SLIDE SHOW EFFECTS Sets the transition effects in slideshow playback. Setting Details SLIDE Switches the screen by sliding in from right to left. BLINDS Switches the screen by dividing into vertical strips. CHECKERBOARD Switches the screen by changing through a checkered pattern. RANDOM Switches the screen with a random effect from SLIDE, “BLINDS”, and “CHECKERBOARD”.
Settings Menu EDIT Menu (still image) . PROTECT/CANCEL Protects files from being deleted accidently. “Protecting/Releasing Protection of the Currently Displayed File” (A p. 62) “Protecting/Releasing Protection of Selected Files” (A p. 63) COPY Copies files from the built-in memory to the SD card. “Copying Files to an SD Card” (A p.
Settings Menu SETUP (video/still image) . Mobile User Guide Displays the QR code to access the Mobile User Guide. . 0 The portal site appears when the QR code has been read correctly. Select the model name of your camera to display its Mobile User Guide. Memo : 0 0 0 To read the QR code, a relevant application is required. Enter the URL in the internet browser manually if the QR code cannot be read. The Mobile User Guide is supported by Android devices and iPhone.
Settings Menu OPERATION SOUND Turns on or off the operation sound. Setting Details OFF Turns off the operation sound. ON Turns on the operation sound. AUTO POWER OFF When no operation is made for 5 minutes, this function turns off this unit or sets this unit to standby mode when using the AC adapter in case you forgot to turn off the power. Setting Details OFF Power is not turned off even if this unit is not operated for 5 minutes.
Settings Menu REC MEDIA FOR IMAGE Sets the recording/playback media of still images. Setting Details I BUILT-IN MEMORY Records still images to this unit’s built-in memory. G SD CARD Records still images to the SD card. FORMAT BUILT-IN MEM. Deletes all files on the built-in memory. Setting Details FILE Deletes all files on the built-in memory. FILE + MANAGEMENT NO Deletes all files on the built-in memory and resets the folder and file numbers to "1".
Settings Menu CONNECTION SETTINGS (video/still image) . DISPLAY ON TV Displays icons and date/time on a TV screen. Setting Details OFF Does not display icons and date/time on TV. ON Displays icons and date/time on TV. VIDEO OUTPUT Sets the aspect ratio (16:9 or 4:3) according to the connecting TV. Setting Details 4:3 Select this when connecting to a conventional TV (4:3). 16:9 Select this when connecting to a widescreen TV (16:9).
Settings Menu USB CONNECTION MENU This menu appears when this unit is connected to a computer using an USB cable. PLAYBACK ON PC 0 Displays videos recorded by this unit by using the Everio MediaBrowser 4. “Installing the Provided Software (Built-in)” (A p. 72) 0 Saves videos recorded by this unit on your computer without using the provided software. “Backing Up Files Without Using Provided Software” (A p. 78) “Copying to Mac Computer” (A p.
Names of Parts Right Side A Speaker . B Grip Belt Pass your hand through the grip belt to hold this unit firmly. “Grip Adjustment” (A p. 8) 0 98 Bottom Side . A Cover Lock B Tripod Mounting Hole “Tripod Mounting” (A p.
Names of Parts Top/Left/Rear Side Inside Terminal Cover . A SD Card Slot A Lens 0 0 0 . The lens is protected by a protective glass cover. If the lens is dirty, use a commercially available lens blower to remove any dust, and a commercially available cleaning cloth to wipe off any dirt. Do not cover the front of the lens with your fingers during recording. B Light 0 Turn on the light when shooting in dark places.
Names of Parts LCD Monitor . A LCD Monitor 0 0 Turns the power on/off by opening and closing. Enables self-portraits to be taken by rotating the monitor. . “Using the Touch Screen” (A p. 11) “Names of Buttons and Functions on the LCD Monitor” (A p. 13) Caution : 0 Do not press against the surface with force or subject it to strong impact. Doing so may damage or break the screen.
Indications on the LCD monitor Common Recording Indications Video Recording . . A TOUCH PRIORITY AE/AF “Capturing Subjects Clearly (TOUCH PRIORITY AE/AF)” (A p. 41) B Backlight Compensation “Setting Backlight Compensation” (A p. 31) C Tele Macro “Taking Close-up Shots (TELE MACRO)” (A p. 33) D WHITE BALANCE “Setting White Balance” (A p. 32) E Time “Clock Setting” (A p. 16) F Recording media “ REC MEDIA FOR VIDEO ” (A p. 94) “ REC MEDIA FOR IMAGE ” (A p.
Indications on the LCD monitor Still Image Recording Video Playback . A Video Mode . A Still Image Mode 0 Switches between video and still image modes. B Image Size “ IMAGE SIZE ” (A p. 88) C Self-Timer “Taking Group Shots (Self-timer)” (A p. 46) D Remaining Number of Shots “Checking the Remaining Recording Time” (A p. 49) E Focus F Recording in Progress 0 Switches between video and still image modes. B Video Quality “ VIDEO QUALITY ” (A p.
Indications on the LCD monitor Still Image Playback . A Still Image Mode 0 Switches between video and still image modes. B Folder Number C File Number D Date/Time 0 Displays the recording date and time. E Recording media “ REC MEDIA FOR IMAGE ” (A p. 95) F Battery Indicator “Checking the Remaining Recording Time” (A p. 48) G SILENT MODE “Using the Silent Mode” (A p. 23) H 1080p Output “ HDMI OUTPUT ” (A p.
Troubleshooting When the unit is not working properly Resetting this Unit 1 Open the terminal cover. 2 Close the LCD monitor to turn off this unit. 3 Press the Reset button gently using an object with pointed tip. 0 Remove the power cord and all connecting cables. Charging Unable to charge the battery. When the battery pack is fully charged, the lamp does not light up. Be sure to charge using the supplied AC adapter.
Troubleshooting Power supply Recording Unable to turn on the power. Recording cannot be performed. The camera does not turn on if the remaining battery power is low. In this case, charge the battery for more than 40 minutes before turning on the power. Check the A / B button. “Top/Left/Rear Side” (A p. 99) Set to the recording mode by tapping the E button on the screen. Recording stops automatically.
Troubleshooting SD Card Playback Cannot insert the SD card. Sound or video is interrupted. Make sure not to insert the SD card in the wrong direction. “Inserting an SD Card” (A p. 9) Do not use a miniSD card or microSD card on this unit (even if the card is inserted in an adapter). It may cause malfunction. “Types of Usable SD Card” (A p. 9) Sometimes playback is interrupted at the connecting section between two scenes. This is not a malfunction. Unable to copy to SD card.
Troubleshooting Editing/Copying Computer Unable to delete file. Unable to copy files to the computer’s HDD. Files (videos/still images) that are protected cannot be deleted. Release protection before deleting the file. “Protecting Files” (A p. 62) If the provided software Everio MediaBrowser 4 is not installed, some functions may not work properly. “Installing the Provided Software (Built-in)” (A p. 72) Before making backup, make sure that enough free space is left in the computer's hard disk (HDD).
Troubleshooting Screen/Image Other Problems The LCD monitor is difficult to see. The buttons on the touch screen do not work. The LCD monitor may be difficult to see if used in bright areas such as under direct sunlight. Tap the buttons on the touch screen with your fingers. The buttons may not respond if you touch them with your fingernails or with gloves on. Disable “SCREEN LOCK”. You cannot operate the touch panel when “SCREEN LOCK” is enabled. “Locking the Screen” (A p.
Troubleshooting This unit does not function properly and error messages appear. This unit is a microcomputer-controlled device. Electrostatic discharge, external noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such a case, close the monitor screen to turn off the power and remove the AC adapter, then press the Reset button to reset this unit. “Resetting this Unit” (A p.
Troubleshooting THIS FILE IS PROTECTED NO FILES Switch off the “PROTECT/CANCEL” function in the “EDIT” menu. “Protecting Files” (A p. 62) Change the setting of “REC MEDIA FOR IMAGE” or “REC MEDIA FOR VIDEO” in the “SETUP” menu, and check that files are not recorded to the other media. “ REC MEDIA FOR VIDEO ” (A p. 94) “ REC MEDIA FOR IMAGE ” (A p. 95) CHECK CARD'S WRITE PROTECTION SWITCH Set the write protect switch of the SD card to off.
Maintenance Perform regular maintenance of this unit to enable it to be used for a long time. Caution : 0 Be sure to detach the AC adapter and power plug before performing any maintenance. Camcorder 0 0 Wipe this unit with a dry, soft cloth to remove any dirt. When it is extremely dirty, soak the cloth in a solution of neutral detergent, wipe the body with it, and then use a clean cloth to remove the detergent. Caution : 0 0 0 Do not use solvents such as benzene, thinner, or alcohol.
Specifications Camera Connectors Item Details Item Power supply Using AC adapter: DC 5.2 V HDMI mini connector Power consumption 2.3 W (60i mode, “LIGHT”: “OFF”, MONITOR BRIGHTNESS: 3 (standard)) 2.5 W (60i mode, “LIGHT”: “OFF”, MONITOR BRIGHTNESS: 4 (brighter)) Rated Current Consumption: 1A HDMI output connector AV output connector Video output: 1.0 V (p-p), 75 Ω Audio output: 300 mV (rms), 1 KΩ USB connector Micro USB Type AB, USB 2.0 compliant Dimensions (mm) 60 x 59.
Specifications AC Adapter (AC-V11U) Item Details Power supply AC 110 V to 240 V, 50 Hz/60 Hz Output DC 5.2 V, 1 A Allowable operating temperature 0°C to 40°C (32°F to 104°F) (10°C to 35°C (50°F to 95°F) during charging) Dimensions (mm) 66 x 28 x 47 (2-5/8” x 1-1/8” x 1-7/8”) (W x H x D: excluding cord and AC plug) Mass Approx. 71 g (0.16 lbs) Memo : 0 The specifications and appearance of this product are subject to changes for further improvement without prior notice.
Trademarks Trademarks 0 0 AVCHD Progressive and AVCHD Progressive logo are trademarks of Panasonic Corporation and Sony Corporation. HDMI (High-Definition Multimedia Interface) and HDMI logo are either registered trademarks or trademarks of HDMI Licensing, LLC in the United States and/or other countries. . 0 0 0 0 0 0 0 0 0 Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. SDXC logo is a trademark of SD-3C, LLC.