Projection Television Users Guide For Models: HD-56FH97 HD-61FH97 HD-70FH97 HD-56FN97 HD-61FN97 HD-70FN97 HD-56FC97 HD-61FC97 HD-70G678 HD-70GC78 Illustration of HD-70FH97 and RM-C14G Important Note: In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference.
Important Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Some pay-per-view programs may be licensed from producers as "view-only" programs.
16) Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.
Warnings Caring for the Cabinet Normally, light dusting with a soft, non-scratching duster will keep your TV clean. If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly moistened with water. You can add a few drops of mild liquid detergent to the water to help remove spots of oily dirt. • • • • DO NOT allow liquid to enter the TV through the ventilation slots. DO NOT use strong or abrasive cleaners on the TV.
Warnings Thank you for purchasing a JVC HDTV-ready projection television which uses the high-quality HD-ILA projection system. This is one of the highest quality and most technologically advanced televisions available today. It is recommended that you read this instruction manual before using your television in order to learn about it’s many features. Cautions related to the safe use of the device and important information which will help you to be able to use this device for a long time is in the Appendix.
Warnings 4. The television requires a lot of electrical power It is recommended that the television is connected directly to the wall socket, and not to another device. When connecting the television to a wall socket that is being used by another device, or when using an extension cord, be careful not to exceed the electrical capacity of the socket. Do not turn the power on and off repeatedly in a short amount of time.
Table of Contents Important Safety Precautions . . 2 Warnings . . . . . . . . . . . . . . . 5 Quick Setup . . . . . . . . . . . . . . 9 Unpacking your TV . . . . . . . . . . . . 9 TV Models . . . . . . . . . . . . . . . . 10 TV Remote Control . . . . . . . . . . . 12 Getting Started . . . . . . . . . . . . . 13 The Remote Control . . . . . . . . . . 13 Connecting Your Devices . . . . . . . 14 Interactive Plug In Menu . . . . . . . . 27 Programming your remote . . . . . . . 30 Onscreen Menus . . . . . . . .
Quick Setup Unpacking your TV Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television, please check to make sure you have all of the following items. In addition to this guide, your television box should include: Television x 1 Remote Control x 1 POWER INDEX SELECT SWAP ML/MTS DISPLAY SLEEP AA Alkaline ASPECT MULTI SCREEN TWIN AA Alkaline TV CATV VCR DVD FREEZE AA Batteries x 2 + INPUT D/A i.
Quick Setup TV Models Before you connect your television to another device, please refer to the proper diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.
Quick Setup Front Panel Diagram Models: HD-56FC97, HD-61FC97, HD-70FH97, HD-70FN97, HD-70G678 and HD-70GC78 POWER POWER LAMP/PROGRAM LAMP/PROGRAM LED LAMP/PROGRAM POWER BUTTON POWER LED Models: HD-56FH97, HD-61FH97, HD-56FN97 and HD-61FN97 LAMP/PROGRAM POWER PUSH LAMP/PROGRAM POWER PUSH LAMP/PROGRAM LED POWER BUTTON POWER LED • For information on the LED, see page 89. Side Panel Diagram INPUT MENU OPERATE + INPUT 4 – VIDEO + L/MONO CHANNEL VOLUME – R AUDIO 11 LCT2067 Eng "D".
Quick Setup Remote Control TV CATV VCR DVD ASPECT POWER MULTI SCREEN TWIN INDEX SELECT FREEZE SWAP ML/MTS DISPLAY SLEEP + INPUT D/A i.LINK MENU 1 2 3 4 5 6 7 8 TIMER FAVORITE 9 RETURN+ TUNE 0 THEATER PRO VIDEO STATUS SOUND NATURAL CINEMA TV SUB CHANNEL SUB LIGHT C.C.
Quick Setup Getting Started These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new television right away. If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual. Step 1 – The Remote Control Before you can operate your remote control, you first need to install the batteries (included). Slide the cover on the back of the remote down towards the bottom of the remote control.
Quick Setup Step 2 – Connecting Your Devices To make these connections, you will use plugs like the ones illustrated below. Component Cables Composite Cables Audio Cables Coaxial Cables Used to connect an external antenna or cable TV system to your TV. Used to connect audio/ video devices like VCRs, DVD players, stereo amplifiers, game consoles, etc. S-Video Cable Used to make video connections with S-Video VCRs, Camcorders and DVD players. Notes: • These connections are examples.
Quick Setup VCR Connection Notes: • Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information. • Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete one set of connections (DVD or audio output) before starting the other to avoid accidentally switching the cables. • You may also connect the DVD player to Input 1.
Quick Setup Diagram #2 Cable or Antenna Output Two-Way Splitter VCR IN OUT OUT V R L IN IN OUT OUT OR Two-Way Splitter (Attachment) IN OUT OUT S-VIDEO R - AUDIO - L VIDEO R - AUDIO - L VIDEO R - AUDIO - L INPUT-1 Coaxial Cable (Attachment) OVER INPUT-2 S-VIDEO ATSC /DIGITAL CABLE IN I VIDEO 75Ω (VHF/UHF) INPUT-3 OVER R - AUDIO - L HDMI 1 TV Rear Panel CENTER CHANNELINPUT Y Pb Pr INPUT-1 Y Pb Pr INPUT-2 S-VIDEO MONITOR /REC OUT AUDIO OUT R L Y Green PB Blue PR V
Quick Setup Connecting to Monitor/Recording Output Terminal TV Rear Panel S-VIDEO MONITOR /REC OUT VIDEO R L R L AUDIO OUTPUT OR VCR IN IN OUT OUT V R L Notes: • When you make this connection, set the Video-1 Monitor Out menu to ON. See page 54. • If you are receiving ATSC/Digital Cable signal, it can be outputted to the S-Video output terminal or Video (composite video) terminal. • If you are receiving Analog TV signal, it can not be outputted to the S-Video output terminal.
Quick Setup Connecting to a Camcorder You may connect a camcorder, game console or other equipment to your television by using the side input jacks (Input 4) located on the side of the television. You can also connect these using the television’s rear input jacks, using the same instructions. INPUT MENU OPERATE + INPUT 4 – VIDEO + L/MONO CAMCORDER CHANNEL VOLUME – R AUDIO 1) Connect a yellow composite cable from the camcorder VIDEO OUT to the VIDEO IN on the side of the TV.
Quick Setup Connecting to the Surround Amplifier (HD-56FH97, HD-61FH97, HD-70FH97, HD-56FN97, HD-61FN97, HD-70FN97, HD-70G678 and HD-70GC78 ONLY) In multi-channel sound such as 5.1 channel, the speech characters are played back from the center speaker. A center speaker in a movie theater is set in back of the screen so it can recreate a conversation scene in the movie more naturally.
Quick Setup Connecting to an amplifier using your optical output You can connect an amplifier that has an optical digital input terminal by using an optical digital cable from the optical output. The signal that is output can be PCM or Dolby Digital. TV Rear Panel Amplifier OPTICAL OUT Digital Audio 1) Connect the optical cable from the back of the TV to the back of the amplifier. Notes: • This terminal can only output digital audio.
Quick Setup Connecting to a Digital TV Receiver By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in their digital form. TV Rear Panel DIGITAL OUT R - AUDIO - L HDMI 1 1 DIGITAL-IN AUDIO OUT L R 2 DTV Decoder HDMI to DVI Cable After the connections have been made, tighten the screw to secure the cables. 1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder to the HDMI1 DIGITAL-IN on the back of your television.
Quick Setup Connecting to an HDMI Compatible Device By connecting an HDMI compatible device, high definition pictures can be displayed on your TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI compatible devices. HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all digital audio/video interface.
Quick Setup Connecting to an AV Receiver using your television's V1 Smart Input By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture sources from many different devices, without having to change or use the other input connections on your TV. This allows you to free up the other input connections so you can connect more devices to your television.
Quick Setup Connecting an i.LINK compatible device to the back of your television i.LINK is a digital serial interface that allows devices equipped with an i.LINK connector to exchange digital video signals, digital audio signals and device control signals bi-directionally over a single cable. (For example, a JVC D-VHS VCR). i.LINK refers to the IEEE1394-1995 industry specification and extensions thereof. The is used for products compliant with the i.LINK standard.
Quick Setup Connecting to the computer (HD-56FH97, HD-61FH97, HD-70FH97, HD-56FN97, HD-61FN97 HD-70FN97, HD-70G678 and HD-70GC78 ONLY) This TV can be used as a computer screen. Use a commercially available D-SUB cable to connect the TV's PC INPUT terminal to the computer's analog RGB output terminal. If you want to listen to the sound from the computer, use a commercially available RCA cable to connect the INPUT-3 audio input terminal to the computer's audio output terminal.
Quick Setup Table of signals for each type of computer Resolution Vertical Frequency (Hz) Horizontal Frequency (kHz) 640 x 480 (VGA) 60.0 31.5 1024 x 768 (XGA) 60.0 48.4 • Only the above formats are supported. • Even with the above formats at 60 Hz, some problems may be experienced depending on the quality of the synchronous signal. (Depending on the quality, some pictures may not be displayed correctly). • Apple Macintosh* computers are not supported.
Quick Setup Step 3 – The Interactive Plug In Menu When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for: • The language in which you want the onscreen menus to appear. • Setting the TV’s clock to the correct time so your timer functions will work properly. You can choose “AUTO” or “MANUAL” for setting the clock. • The auto tuner setup of which channels you wish to receive.
Quick Setup Auto Clock Set Before you use any of your TV’s timer functions, you must first set the clock. You may precisely set your clock using the XDS time signal broadcast by most public analog broadcasting stations. If you do not have this in your area, you will have to set the clock manually. See manual clock set below. To set the clock using the XDS signal: √® SET CLOCK † MODE TIME TIME ZONE DATE/YEAR D.S.T.
Quick Setup Auto Tuner Setup In auto tuner setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals. This means when you scan (using the CHANNEL +/– buttons) you will receive only clear, active channels. There are two tuner modes to choose from, ANALOG or DIGITAL. AUTO TUNER SETUP IN ANALOG TUNER MODE IN DIGITAL TUNER MODE AIR ATSC START SELECT OPERATE MENU EXIT Now Programming...
Quick Setup Remote Programming You can program your remote to operate your cable box, satellite receiver, VCR or DVD player by using the instructions and codes listed below. If the equipment does not respond to any of the codes listed below or to the code search function, use the remote control supplied by the manufacturer. Cable Box or Satellite Codes The remote control is programmed with cable box and satellite codes for power on/off, channel up/down, and 10 key operation.
Quick Setup VCR Codes The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward, rewind, pause, record, channel up/down operation. 1) Find the VCR brand from the list of codes shown below. 2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”. 3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad. 4) Release the DISPLAY button, and confirm the operation of the VCR.
Quick Setup DVD Codes The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward, rewind, previous/next chapter, tray open/close, and still/pause operation. 1) Find the DVD player brand from the list of codes shown below. 2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”. 3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad.
Quick Setup Search Codes Cable/Satellite Search Codes Function 1) 2) 3) 4) Slide the first 2-Way Mode Selector switch to CATV. Press the POWER and RETURN+/TV buttons. Hold for at least three seconds and release. Press the POWER button on the remote, and see if the cable or satellite box responds. If there was a response, press RETURN+/TV. The codes are now set. If there was no response, repeat Step 3.
Onscreen Menus Using the Guide Certain symbols are used throughout this guide to help you learn about the features of your new television. The ones you will see most frequently are: π† Up and Down arrows mean press the CH+ or CH– buttons.
Onscreen Menus The Onscreen Menu System Your television comes with JVC’s onscreen menu system. The onscreen menus let you make adjustments to your television’s operation simply and quickly. Examples of the onscreen menus are shown on the next page. Detailed explanations on using each menu follow later in this guide. For information about the interactive plug-in Menu, see pages 27 - 29. The Onscreen Menu System To open the onscreen menu system, press the MENU button on the remote control.
Onscreen Menus Press the MENU button To INITIAL SETUP 03 CLOCK / TIMERS INITIAL SETUP PREVIOUS AUTO TUNER SETUP CHANNEL SUMMARY V-CHIP SET LOCK CODE PREVIOUS VIDEO-1 MONITOR OUT TV SPEAKER AUDIO OUT LAMP TIMER RESET OPERATE MENU (4/5) NEXT PAGE EXIT SELECT INITIAL SETUP 04 MENU EXIT SOUND ADJUST 10 40 TURN ON VOLUME VOLUME LIMIT RESET OPERATE MENU (5/5) NEXT PAGE EXIT SELECT INITIAL SETUP 05 MENU EXIT EXIT ON OFF ON OFF SELECT (2/5) OPERATE MENU EXIT INITIAL SETUP 02 INITIAL
Onscreen Menus Auto Tuner Setup The auto tuner setup function is described on page 29 as the interactive plug-in menu. If you need to run the auto tuner setup again, follow the steps below.
Onscreen Menus Channel Summary Channel summary allows you to customize the line-up of channels received by your TV. Regarding analog channels, you can add or delete channels from the line-up or prevent any unauthorized viewers from watching any or all 191 channels. Regarding digital channels, the only channels that will appear are the ones that are broadcasting.
Onscreen Menus How to set the channel label. (This is only for analog broadcasting.) Press the MENU button π† √® π† To CHANNEL SUMMARY To operate To the ID column ID CHANNEL 09 RESET Press the OK button to enter √® π† To select the character you want To move to the next space PRESS SELECT OK TO FINISH OPERATE MENU EXIT ...
Onscreen Menus Channel Guard Message When a viewer attempts to watch a guarded channel, the following message appears: To watch a channel that you have locked, enter the Lock Code using the 10 key pad. If the wrong code is entered, the message “INVALID LOCK CODE!” will flash on the screen. THIS CHANNEL IS LOCKED BY CHANNEL GUARD. PLEASE ENTER LOCK CODE BY 10 KEY PAD TO UNLOCK IT. The channel cannot be accessed until the correct code is entered. NO.
Onscreen Menus Unrated Programs Unrated programming refers to any programming which does not contain a rating signal. Programming on television stations which do not broadcast rating signals will be placed in the “Unrated Programming” category.
Onscreen Menus US V-Chip Ratings U.S. PARENTAL RATING SYSTEMS Programs with the following ratings are appropriate for children. ❒ TV Y is Appropriate for All Children Programs are created for very young viewers and should be suitable for all ages, including children ages 2 - 6. ❒ TV Y7 is for Older Children Most parents would find such programs suitable for children 7 and above. These programs may contain some mild fantasy violence or comedic violence, which children should be able to discern from reality.
Onscreen Menus Setting US V-Chip Ratings Press the MENU button π† √® To V-CHIP To operate (lock icon V-CHIP V-CHIP appears) Press ZERO to access the V-Chip menu √® π† √® To turn V-Chip ON or OFF To move to SET US TV RATINGS To enter OFF SET US TV RATINGS SET MOVIE RATINGS SET CANADIAN RATINGS ENG SET CANADIAN RATINGS FRE UNRATED SELECT VIEW OPERATE MENU EXIT Directions to set US V-Chip Ratings Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.
Onscreen Menus Movies Ratings ❒ NR – Not Rated This is a film which has no rating. In many cases these films were imported from countries which do not use the MPAA ratings system. Other NR films may be from amateur producers who didn’t intend to have their film widely released. NR (Not Rated) Programming may contain all types of programming including children’s programming, foreign programs, or adult material.
Onscreen Menus Canadian V-Chip Ratings ❒ E – Exempt Exempt programming includes: news, sports, documentaries and other information programming, talk shows, music videos, and variety programming. ❒ C – Programming Intended for Children Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature.
Onscreen Menus Set Lock Code Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below.
Onscreen Menus Language The language function is described on page 27 as the interactive plug-in menu. If you need to choose the language again, follow the steps below. Press the Menu button π† √® INITIAL SETUP To LANGUAGE To choose a language: ENG. (English), FRAN. (French) or ESP. (Spanish) PREVIOUS LANGUAGE Press the MENU button when finished XDS ID ENG. FRAN. ESP.
Onscreen Menus Digital Auto Setting Press the MENU button π† √® π† √® π† √® π† √® √® π† To CLOSED CAPTION To enter To Type To select Auto, Advanced or Basic Auto: Shows closed caption a priority for digital channels over analog channels. It is set automatically. Advanced: Shows only the digital closed caption. Basic: Shows only the analog closed caption.
Onscreen Menus Digital Manual Setting Press the MENU button To CLOSED CAPTION √® To enter π† To Type √® To select Auto, Advanced or Basic π† To Service √® To select 1, 2, 3, 4, 5 or 6 π† To Appearance √® To enter √® To select Manual π† To Font √® To enter π† To select Font Size or Font Style √® To select the setting you like Font Size: Auto, Standard, Large or Small Font Style: Auto, Serif Mono, Serif, Sanserif mono, Sanserif, Casual, Cursive or Small Capital π† To Set Press the OK button to save π† π† √®
Onscreen Menus Auto Shut Off This function automatically shuts off your TV when there is no signal from the channel the TV is on. Press the MENU button π† √® INITIAL SETUP PREVIOUS To AUTO SHUT OFF To turn ON or OFF LANGUAGE Press the MENU button when finished XDS ID • If the channel that you have on does not receive a signal for more than one minute, the blinking text “NOT RECEIVING A SIGNAL AUTO SHUT OFF IN 9 MIN.” appears on the screen, and starts the countdown.
Onscreen Menus Front Panel Lock This allows you to lock the keys on the side of the TV, so that a child may not accidentally change your viewing preferences. Press the MENU button π† √® To FRONT PANEL LOCK To turn ON or OFF Press the MENU button when finished You can turn off this feature in the following ways: • Unplug the power cord, and plug it back in. Do this if your batteries die or you lose your remote control.
Onscreen Menus Video Input Label This function is used to label video input connections for the onscreen displays.
Onscreen Menus Position Adjustment Position adjustment allows you to adjust the position of the picture on the screen vertically when the aspect is set to panorama or cinema. Press the MENU button π† √® π †√® To POSITION ADJUSTMENT To enter To adjust the position Press the MENU button to finish Notes: OPERATE OK RESET MENU EXIT • To reset the adjustment to the center, press the OK button. • When the arrow disappears, while you are adjusting the position, the position is at its maximum limit.
Onscreen Menus Video-1 Monitor Out This function allows you to set whether the signal, which comes from VIDEO-1 input terminal, should be output from MONITOR OUT terminal. If you select it from MONITOR OUT, set it to "ON".
Onscreen Menus Digital-In The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when an HDMI480p picture signal is being input to the DIGITAL-IN terminal. This option adjusts the position when an HDMI or DVI 480p picture signal is being displayed on the screen. There are two types of HDMI480p picture signals: 640x480 and 720x480. If the displayed picture is slightly shifted, the position can be adjusted by selecting either SIZE1 or SIZE2.
Onscreen Menus Center CH Input HD-56FH97, HD-61FH97, HD-70FH97, HD-56FN97, HD-61FN97, HD-70FN97, HD-70G678 and HD-70GC78 ONLY When you are using a surround system, you can substitute the speaker of this television for the center speaker of your surround system. Set CENTER CH INPUT to ON when you use the speaker as the center speaker of your surround system. The volume differs when the TV is being utilized as the Center Channel Input versus when it is not.
Onscreen Menus Antenna Level Confirms the present antenna level. Antenna Level Press the MENU button π† √® π† √® To DIGITAL SETUP To enter To Antenna Level To enter 75 BACK Back MENU Exit Note: • If you are watching an analog channel or a signal from your i.LINK device, antenna level will not appear. Digital Sound You can select the optical digital sound output, either PCM or Dolby Digital when your TV is connected to an amplifier that has Dolby Digital decoder.
Onscreen Menus Cable Card Application Press the MENU button π† √® π† √® To DIGITAL SETUP To enter To Cable Card Application To enter Press the OK button The application will perform i.LINK Auto Play When playing a D-VHS tape, you can set it to the i.LINK input automatically, or manually. Press the MENU button π† √® π† √® To To To To DIGITAL SETUP enter i.LINK Auto Play select ON or OFF ON: Set to i.
Onscreen Menus Picture Settings These settings allow you to change and adjust the way the picture appears on your television. TINT Tint allows you to adjust the levels of red and green in your TV picture. COLOR The color function lets you make all the colors in the TV picture appear either more vivid or subtle. PICTURE Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker or brighter picture overall.
Onscreen Menus Color Management This TV supports the COLOR MANAGEMENT function to ensure dull colors are compensated to produce natural hues. Press the MENU button π† √® π† To COLOR MANAGEMENT To enter To select the mode “ON" or "OFF" COLOR MANAGEMENT ON OFF Press the MENU button when finished Dynamic Gamma JVC's Dynamic Gamma Circuitry (DGC) makes it easier to see dark areas when a picture has many dark areas, and makes it easier to see the bright areas when a picture has many bright areas.
Onscreen Menus Digital VNR This function can be selected to change the effect of Digital VNR (Video Noise Reduction). Press the MENU button π† √® π† DIGITAL VNR AUTO MIN MAX OFF To DIGITAL VNR To enter To select the effect you like. AUTO: adjusts the effect of VNR automatically. MIN: adjusts the effect of VNR to minimum. MAX: adjusts the effect of VNR to maximum. OFF: turns the effect of VNR off. Press the MENU button when finished Notes: • If it is in PC, Digital VNR will not be displayed.
Onscreen Menus Sound Settings These settings allow you to change and adjust the sound on your television. BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with the bass adjustment. TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio. BALANCE – Adjust the level of sound between the TV’s left and right speakers with the balance setting.
Onscreen Menus Set Clock The set clock function is described on page 28 as the interactive plug-in menu. You can choose to set the clock automatically or manually. If you need to set the clock again, follow the steps below. Press the MENU button π† √® To SET CLOCK To enter When you set the clock automatically, choose AUTO by pressing the π† √® ATLANTIC EASTERN HAWAII π† √® √ or ® arrows. To TIME ZONE To select your time zone CENTRAL ALASKA MOUNTAIN SET CLOCK PACIFIC To D.S.T.
Onscreen Menus On/Off Timer The on/off timer lets you program your television to turn itself on or off. You can use it as an alarm to wake up, to help you remember important programs, or as a decoy when you’re not home.
Onscreen Menus Lamp Timer Reset The lamp replacement message will appear when you need to change the lamp. After you replace the lamp, you need to reset the timer which is built into your television. Press the MENU button π† To LAMP TIMER RESET √® To Enter CLOCK / TIMERS PREVIOUS SET CLOCK ON / OFF TIMER LAMP TIMER RESET The following message will appear. NEXT PAGE PRESS OK TO RESET THE LAMP TIMER.
Button Functions Multi Screen Function Your television has two kinds of screen: TWIN (2 channels) and INDEX (12 channels). Note: After you press any multiscreen buttons, if you press the menu button, only the picture adjust screen will appear. Twin Activate the split-screen option by pressing TWIN on the remote control. The channel (or input) you were watching before pressing TWIN will appear on the left, the new channel will appear on the right.
Button Functions Index This allows you to quickly look at up to 12 channels at a time so that you can decide which one to watch. 1 2 3 4 5 6 7 8 9 10 11 12 Notes: • Only Analog channel input signal will be displayed. • You can watch the channel added in channel summary. See page 38. Freeze Pressing the FREEZE button causes the screen to change to the split-screen display with the still picture displayed on the right. In order to return to the normal display, press the FREEZE button once again.
Button Functions Power Turns the TV on or off. Press the POWER button Note: • After turning the power on, you can not turn the power off for about one minute. Number Buttons - 10Key Pad Use the number buttons on the remote control to move directly to a specific channel. For example, to move to channel 12: 0 (Zero) 1 (One) 2 (Two) Tune Lets you decide the input channel and select it. After you press the number buttons on the remote, press the TUNE button.
Button Functions Channel +/– Use these buttons to move up or down all the available channels your TV is able to receive. Volume +/– Use these buttons to raise or lower the TV’s volume level. The maximum is the level you set in Volume Limit. See page 62. TheaterPro D6500K The TheaterPro D6500K color temperature technology function makes sure that the video you watch is set to the standard color temperature, so that what you see is as true to what the film to video editors intended it to be.
Button Functions Sound By pressing the SOUND button, you can change the A.H.S.+ (Advanced Hyper Surround plus) mode, VOICE ENHANCEMENT or A.T.C. (Advanced Tone Correction), SMART SOUND or MaxxBass on or off. A.H.S.+ - Adds a more spacious surround sound. Music gives basic effect and movie for more effect. VOICE ENHANCEMENT - Gives a clearer sound quality of the voices in what you are watching. (HD-56FH97, HD-61FH97, HD-70FH97, HD-56FN97, HD-61FN97, HD-70FN97, HD-70G678 and HD-70GC78 ONLY). A.T.C.
Button Functions Video Status The VIDEO STATUS button gives you a choice of four TV picture display settings, including a display of your own preferences. VIDEO STATUS Standard - Resets the picture display to the factory settings. Dynamic - Gives a vivid picture with better contrast when viewing in a brightly lit room. Theater - Gives a rich, film-like look to video when viewing in a dimly lit room. Game - Used for when you are playing video games connected to your TV.
Button Functions Sleep Timer The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work for a total time of up to 180 minutes. Press the SLEEP button 0 15 30 45 60 90 120 180 Sleep Timer Message 60 seconds before the automatic shutoff, this message will appear: GOOD NIGHT!! PUSH SLEEP TIMER BUTTON TO EXTEND You then have 60 seconds to press the SLEEP button to delay the shut off.
Button Functions Display The display screen shows the current status of timers, inputs and XDS ID.
Button Functions Favorite The Favorite button allows you to select your favorite channels easily. First, you must register the channels that you like. See how to register below. Press the FAVORITE button The favorite channel list will appear. π† To select the channel you want to watch Press the OK button It will change to the channel you have selected.
Button Functions Aspect This feature will help you adjust the picture you are watching to give you the best possible picture quality. Aspect Ratios PANORAMA - With this ratio a normal 4:3 aspect picture is stretched to fit the dimensions of the 16:9 aspect screen. CINEMA - This ratio “zooms in” on the center part of a 4:3 aspect picture, blowing it up to fill the 16:9 screen. FULL - This is the ratio to use when watching 16:9 High-Definition broadcasts.
Button Functions Aspect Ratios (Continued) Press the ASPECT button • By pressing the ASPECT button, you can change the size. When you change the aspect ratios, it is different from their broadcast or recorded program.
Button Functions TV/CATV Slide Switch Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to operate the television’s built-in tuner. Move the switch to CATV to operate a cable box. Note: • See page 30 for information on programming your remote for cable box operation. VCR/DVD Slide Switch You can control a VCR or DVD player with the buttons on the lower part of the remote control. Move the slide switch to VCR or DVD to operate.
Button Functions D/A (Digital/Analog) The D/A button changes the analog and digital channel. Each time you press the D/A button, you can switch back and forth the analog and digital channels. Digital channels have a "D" in front of the channel number. Note: • If the cable card is inserted into the TV, you cannot use the D/A button. You can select a digital channel only.
Button Functions i.LINK Menu i.LINK has two menus - Controller and Device. By connecting a D-VHS VCR with an i.LINK cable, you can set the timer easily. Notes: • The i.LINK/Timer function will only work when you are receiving digital programming only. • As for the connection of a D-VHS VCR with the i.LINK cable, see page 24. • When operating the i.LINK, don't insert or disconnect the i.LINK cable. Controller You can operate a D-VHS VCR connected with an i.LINK cable by using this controller.
Button Functions Device To operate, select a device. i.LINK Controller Renumber Page 2/3 Device D-VHS1 JVC HM-DH30000U D-VHS2 JVC HM-DH40000U HD-MOVIE 1 JVC GR-HD1 π† To select your device connecting with i.LINK Press the OK button Notes: • If you do not select the device, you cannot use the i.LINK timer functions. • When one device is selected and you select controller, you will move to the Controller onscreen. • The devices listed on the device onscreen are only D-VHS and HD-MOVIE that have i.
Button Functions Timer You can set the two timers: Record and view. The timer starts the recording or turns to the channel you set for it automatically. Reservation Press the TIMER button π† To New Reservation Press the OK button New Reservation Timer Sept. 10 (Wed) Timer Mode Channel 0. New Reservation Reservation New V 80-3 PBS1DTV Sep. 11 (Wed) R i.LINK 335-1 KDVRet Sep. 11 (Wed) R R i.LINK † † √® † √® † √® † √® † √® † √® † Sep.
Button Functions Timer Edit When you want to confirm the timer you set or edited, or delete the timer setting, use this function. Timer Edition Press the TIMER button π† √®π† To change the setting you want to edit Sept. 10 (Wed) Timer Mode To select the timer list you want to edit Press the OK button † Timer Edit Timer Channel 0. New Reservation V 80-3 PBS1DTV Sep. 11 (Wed) R i.LINK 335-1 KDVRet Sep. 11 (Wed) To Set Timer R Press the OK button R i.
OSD Information Weak Signal This OSD appears when the digital channel that you have selected is too weak to receive or no signal is being detected for that channel. Weak Signal 15 No Program If the external input terminal you selected, or were watching is not receiving a signal, "NO PROGRAM" appears on the television screen. It appears when that external input terminal is not receiving a signal and you have the Noise Muting function OFF and you have a single screen.
Cable Card Information Cable card offers information when a cable card is inserted into the CABLE CARD slot on the back of the TV. Notes: • Please contact your local cable company regarding detailed information. • When the cable card is inserted into the cable card slot, if you turned the power off, the fan will continue to rotate because the program information is being renewed. This is normal.
Lamp Replacement Changing the Lamp WARNING! It is very important that you NEVER TOUCH THE GLASS SURFACE OF THE NEW LAMP. Touching the glass surface will deposit oils from your hand onto the lamp surface. When the lamp heats up to its operating temperature, the oil will cause a difference in temperature on the lamp surface that will likely cause the lamp to break. Replace the lamp with part number TS-CL110U only! The television is designed to work specifically with this lamp.
Lamp Replacement Replacement Lamp Kit Before replacing the lamp, you will need to purchase a replacement kit, part number TS-CL110U. To purchase this kit, consult your dealer or call 1-800-252-5722 or go to www.jvc.com. Because the lamp contains mercury, it cannot be disposed of with normal trash. Lamp Message LAMP NEEDS TO BE REPLACED. REFER TO OWNER'S MANUAL FOR REPLACEMENT INSTRUCTIONS. AFTER REPLACING THE LAMP, PLEASE RESET TIMER IN THE TV MENU. PRESS OK, IF YOU DO NOT WANT TO SEE THIS MESSAGE AGAIN.
Lamp Replacement How to Replace the Lamp Please read these instructions fully before attempting to replace the lamp. If you feel unsure about replacing the lamp yourself, call a service technician. Please observe all safety warnings. 1) Turn off the television. Press the POWER button on the remote control or TV front panel. Wait until the picture has closed and the LAMP LED on the front panel has stopped blinking indicating the lamp cool down is complete.
Lamp Replacement 4) Remove the lamp unit. Using a Philips head type screwdriver (cross-head type), loosen the two screws fastening the lamp unit. When the screws have been loosened, remove the lamp by raising the handle and gently sliding the unit straight towards you. Place it carefully in the recycling packaging. 5) Install the new lamp unit. Holding the handle attached to the new lamp unit, slide and push the new lamp straight into the television and back into the lamp housing area.
Lamp Replacement Warning LED Messages While the power is on, and there is a problem with the TV, the TV changes to warning mode and informs you of the problem using the LED as follows. Then, the power turns off automatically and performs the cooling for approximately 1 minute. The LAMP/PROGRAM LED blinks Condition: It may be a malfunction of the internal electrical circuits. To correct: Keep the TV off for a while and then turn the power on again.
Troubleshooting PROBLEMS There is no power CHECK • See if the power cord became unplugged. • Check for a blown fuse or circuit breaker or a power outage. • It is possible the fan is stuck or the inside temperature is rising abnormally. Consult your dealer. The POWER LED • It may be a malfunction that the fan is locked or the temperature has increased. and LAMP/PROGRAM LED are blinking alternately. The POWER LED • The lamp may not have been installed correctly, or it may be due to a malfunction.
Troubleshooting PROBLEMS CHECK There is no sound from the TV's speaker • The Center CH Input may be turned on. See page 56. • The TV Speaker option may be turned off. See page 54. Static electricity • It is normal to feel static electricity if you brush or touch the screen. You hear occasional crackling sounds • It is normal for the TV to make crackling sounds when first turned on or off. Unless the sound or picture become abnormal, this is fine.
Specifications Model HD-56FH97 HD-56FN97 HD-61FH97 HD-61FN97 HD-70FH97, HD-70FN97 HD-70G678, HD-70GC78 Type HD-ILA Device Projection Reception Format NTSC, BTSC System (Multi-Channel Sound) ATSC Terrestrial, Digital Cable Reception Range VHF 2 to 13, UHF 14 to 69 at ATSC, CATV 135 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyper and Ultra bands (191 channel frequency synthesizer system) at Analog • Reception of channel A-5 ("95" of th
Specifications Model HD-56FC97 HD-61FC97 Type HD-ILA Device Projection Reception Format NTSC, BTSC System (Multi-Channel Sound) ATSC Terrestrial, Digital Cable Reception Range VHF 2 to 13, UHF 14 to 69 at ATSC, CATV 135 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyper and Ultra bands (191 channel frequency synthesizer system) at Analog • Reception of channel A-5 ("95" of the TV set's on-screen cable channel numbers) is not recommended
LCT2067 Eng "D".
LCT2067 Eng "D".
JVC COMPANY OF AMERICA Division of JVC Americas Corp. 1700 Valley Road Wayne, New Jersey, 07470 LCT2067 Eng "D".indd 96 JVC CANADA, INC.