® ENGLISH VIDEO CASSETTE RECORDER CONTENTS SAFETY FIRST 2 Safety Precautions ...................... 2 HR-J461MS INSTALLING YOUR NEW RECORDER 3 Basic Connections ..................... 3 INITIAL SETTINGS 4 Video Channel Set ..................... 4 Auto Set Up ............................... 6 On-Screen Displays ................... 8 Select Language ......................... 9 Clock Set.................................. 10 PLAYBACK 11 Basic Playback ......................... 11 Playback Features .
EN SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel.
INSTALLING YOUR NEW RECORDER 1 2 Aerial terminal RF Cable (provided) TV Aerial Cable AV-IN terminals 3 AV Cable (not provided) Mains Power Cord Rear View Mains outlet 3 It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED. Basic Connections Back of TV EN AUDIO OUT/ VIDEO OUT Connect the power plug to an AC outlet before installing the lithium battery. Z pg.
EN INITIAL SETTINGS Video Channel Set Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below. If you have connected the video recorder to your TV via both the provided RF cable and an AV cable (AV connection) – Go to "With AV Connection" on next page.
EN 3 SET VIDEO CHANNEL Set your TV to UHF channel 36. ● If the two vertical white bars appear clearly on the screen as shown in the illustration (Z "TEST SIGNAL" on page 4), press OK and then go to step 4. ● If the two vertical white bars do not appear clearly, press OK and then TV PROG + or – to set the video recorder to a vacant channel between 28 and 60 which is not occupied by any local station in your area. (Ex.
EN INITIAL SETTINGS (cont.) 1 2 1 2 3 4 5 6 7 8 9 2 0 3 4 4 1 3 OK MENU PUSH JOG SELECT LANGUAGE Press PUSH JOG %fi to place the pointer next to your desired language (English, Chinese or Russian), then press OK or PUSH JOG . fi ● Don't press any buttons on the recorder or remote that are not directly related to the step you are performing while Auto Set Up is in progress.
EN TV System Australia, New Zealand, Kuwait, U.A.E., Indonesia, Singapore, Thailand, Malaysia, Iran, Saudi Arabia,Egypt, Morocco, Lebanon, Iraq B/G China, Mongolia, Russia D/K Hong Kong I 7 8 9 0 4 5 6 SELECT TV SYSTEM Press PUSH JOG %fi to place the pointer next to the appropriate TV system (refer to the table on the left). START AUTO CHANNEL SET Press OK or PUSH JOG . fi Major Countries ● The Auto Set Up function scans all the channels that are receivable by your recorder.
EN INITIAL SETTINGS (cont.) You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. 1 Turn on the TV and select the VIDEO channel (or AV mode). 2 1 2 3 4 5 6 7 8 9 3 2 0 4 4 1 Press . ACCESS MAIN MENU SCREEN Press MENU. ACCESS FUNCTION SET SCREEN Place the pointer next to "FUNCTION SET" by pressing PUSH JOG %fi, then press OK or PUSH JOG .
EN Turn on the TV and select the VIDEO channel (or AV mode). 1 2 3 4 5 6 7 8 9 1 2 3 Press . ACCESS MAIN MENU SCREEN Press MENU. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . fi Select Language TURN ON THE RECORDER MAIN MENU FUNCTION SET TUNER SET INITIAL SET [5/∞] = [MENU] : EXIT 2 1 3 OK MENU PUSH JOG 4 5 6 Press PUSH JOG %fi to place the pointer next to "LANGUAGE", then press OK or PUSH JOG .
EN INITIAL SETTINGS (cont.) 1 2 3 4 5 6 7 8 9 2 0 4 . ACCESS MAIN MENU SCREEN Press MENU. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . fi Turn on the TV and select the VIDEO channel (or AV mode). 1 2 3 4 Press ACCESS CLOCK SET SCREEN Press PUSH JOG %fi to place the pointer next to "CLOCK SET", then press OK or PUSH JOG . The Clock Set screen appears.
PLAYBACK EN The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Basic Playback Turn on the TV and select the VIDEO channel (or AV mode).
EN PLAYBACK (cont.) Variable-Speed Search PLAY During playback, press PUSH JOG fi 1 ACTIVATE VARIABLE-SPEED SEARCH % Playback Features or . RE ● The more times you press, the faster the playback picture moves. ● To decrease speed, press the button for the opposite direction. W To resume normal playback, press PLAY. 2 3 4 5 6 7 8 9 2 2 0 1 Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture. ACTIVATE FRAME-BY-FRAME PLAYBACK Press PAUSE.
EN 13 Manual Tracking Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. REVIEW 1 2 3 4 5 6 7 8 9 2 0 4 TV PROG AY PL 1 1 FF REW PAUSE 2 ST O P 3 3 OVERRIDE AUTOMATIC TRACKING Press (SP/LP/EP) on the remote to engage manual tracking. ADJUST TRACKING MANUALLY Press TV PROG + or – to adjust tracking.
EN PLAYBACK (cont.) Index Search Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. £ 2 NOTE: 1 2 Before starting, make sure the recorder is in the Stop mode. 3 2 6 7 8 9 0 4 TIMER 1 ACTIVATE INDEX SEARCH Press PUSH JOG or (™ or £) on the remote control. "™ 1" or "£ 1" is displayed on screen and search begins in the corresponding direction.
EN The Next Function Memory "tells" the recorder what to do after rewinding. Before continuing, ensure that the recorder is in the Stop mode. a– For Automatic Start Of Playback After Tape Rewind... ...press REW, then press PLAY within 2 seconds. b– For Automatic Power Off After Tape Rewind... ...press REW, then press within 2 seconds. c– For Automatic Timer Standby After Tape Rewind... ...press REW, then press TIMER within 2 seconds.
EN RECORDING TV signals being received by the recorder's built-in tuner can be recorded onto a video tape. You can "capture" a TV programme using your video recorder. Basic Recording 1 PLAY STOP/EJECT RD RE CO LO CO U R TV SY PR ST O G EM SP/LP/EP Turn on the TV and select the VIDEO channel (or AV mode). 1 2 3 2 4 5 6 7 8 9 0 NUMBER 4 TV PROG AY PL SP/LP/EP 1 PAUSE RECORD ST O P 3 2 3 4 5 6 LOAD A CASSETTE Insert a cassette with the record safety tab intact.
EN 17 Record One Programme While Watching Another Recording Features 1 SELECT CHANNEL TO WATCH Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view. ● The programme selected with the TV's channel controls appears on the TV screen while the one selected with the TV PROG buttons is recorded on the tape. RECORD TV PROG Elapsed Recording Time Indication You can check the exact time of a recording.
EN RECORDING (cont.) B.E.S.T. Picture System PLAY Turn on the TV and select the VIDEO channel (or AV mode). The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is "ON". Preparation 1 CO RD 2 Press . ACCESS MAIN MENU SCREEN Press MENU.
EN Recording 1 START RECORDING Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE Playback The recorder assesses the quality of the tape once you initiate playback. 1 START PLAYBACK Press PLAY. ● The recorder adjusts the playback picture quality based on the quality of the tape in use. ● B.E.S.T. is active during Auto Tracking. "BEST" appears blinking on the recorder's display panel.
EN TIMER RECORDING Express Timer Programming 1 1 ACCESS TIMER PROGRAMMING SCREEN Press PROG (If you're just starting out, "P1" appears). ST EM 2 CO LO U R SY 3 1 2 4 3 2 5 6 7 8 9 /– P+ O ST 4 0 4 TV PROG+/– START+/– D 1 / E+ AT PROG – 3 = 5 STOP –:– – SP DATE – –.– – [+/–] = [PROG] : EXIT Remember, the clock must be set before you can programme the timer (Z pg. 10). Before performing the following steps: ● Insert a cassette with the safety tab in place.
SP/LP/EP EN 6 7 21 SET TAPE SPEED Press SP/LP/EP ( ) to set the tape speed. RETURN TO NORMAL SCREEN After confirming all information is correct, press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ● Repeat steps 1 – 7 for each additional programme. LY 8 3 AI 2 D 1 4 5 6 7 8 9 0 2 WEEKLY 4 TIMER SP/LP/EP PROG 1 ENGAGE RECORDER'S TIMER MODE Press TIMER. The recorder turns off automatically and "‰" appears on the display panel.
EN TIMER RECORDING (cont.) Check, Cancel And Replace Programmes 1 2 3 4 5 6 8 9 1 7 CANCEL STOP+/– 2 0 TIMER 4 TV PROG+/– 2 DISENGAGE TIMER MODE Press TIMER, then press ACCESS PROGRAMME CHECK SCREEN Press PROG CHECK. START+/– D AT PROG CHECK1 E+ PR START STOP CH 1 8:00 10:00 3 2 10:00 10:45 2 3 11:30 13:00 1 4 5 6 7 8 [PROG CHECK] : NEXT DATE 24.12 25.12 25.12 /– EP P/ /L SP 3 .
EN 23 Auto SP→LP Timer Auto Timer If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode (with PAL broadcasts) or EP mode (with NTSC broadcasts) to allow complete recording. For Example . . . Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape.
EN SPECIAL FEATURES Remote A/B Code Switching Remote Control Functions The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control's A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.
EN 25 TV Multi-brand Remote Control TV Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer's TVs can also be controlled. Before you start . . . ● Turn on the TV using its remote control. VCR TV/VCR 1 2 3 4 5 6 7 8 9 2 0 CANCEL 4 NUMBER TIMER 1 SET TV BRAND CODE Refer to the chart below. While holding down TV on the recorder's remote control, enter your TV's brand code using the NUMBER keys, then press STOP.
EN EDITING You can use your video recorder as the source player or the recording deck. Edit To Or From Another 1 Video Recorder 2 1 2 3 3 2 4 5 6 7 8 9 0 NUMBER "0" MAKE CONNECTIONS Connect the player's AUDIO/VIDEO OUT connector to the recorder's AUDIO/VIDEO IN connector. SET RECORDING DECK'S INPUT MODE Set to AUX.
EN Edit From A Camcorder You can use a camcorder as the source player and your video recorder as the recorder. 1 LO U R SY ST EM 2 3 CO 27 MAKE CONNECTIONS Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's front panel AUDIO/VIDEO input connectors. SET RECORDER'S INPUT MODE Press NUMBER key "0" and/or TV PROG so that "F-1" appears on the display panel. SELECT "EDIT" FOR PICTURE CONTROL SET MODE Follow the "Picture Control" section on page 15, then select "EDIT.
EN INFORMATION ON MULTI-SYSTEM COMPATIBILITY Setting Of The Colour System Select Buttons Mode Display Use the COLOUR SYSTEM button on the front panel to select the colour system. Pressing this button changes the mode as illustrated on the left. The On-Screen display will show which mode is selected. Mode AUTO AUTO Usually set to this mode. This mode automatically detects PAL, NTSC, MESECAM and adjusts to the colour system being recorded or played back.
EN 29 Playback This recorder can play back all 3 types of recorded tape. HR-J461MS Recorded tape PAL Playback circuit Multi-system receiver PAL MESECAM Built-in RFconverter K, I, G, H MESECAM NTSC[PAL NTSC PAL (B/G, D/K, I, H) RF OUT NTSC 3.58 MHz Multi-system monitor Manual switching Manual switching NTSC 4.43 MHz VIDEO OUT AUDIO OUT PAL SECAM NTSC 3.58 NTSC 4.
EN TUNER SET 3 1 2 3 4 5 6 7 8 9 ACCESS TUNER SET SCREEN Press PUSH JOG %fi to place the pointer next to "TUNER SET", then press OK or PUSH JOG . fi Turn on the TV and select the VIDEO channel (or AV mode). [5/∞ ] = [MENU] : EXIT 2 4 TV PROG 4 SELECT AUTO CH SET MODE Press PUSH JOG %fi to place the pointer next to "AUTO CH SET", then press OK or PUSH JOG .
EN 31 Manual Channel Set Store channels that were not stored during Auto Set Up (Z pg. 6) or Auto Channel Set (Z pg. 30). 5 6 7 8 9 2 0 4 1 3 MENU OK PUSH JOG 1 2 3 4 ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT POSITION Press PUSH JOG %fi to place the pointer next to an open channel position, then press OK or PUSH JOG . fi 4 Perform steps 1 – 3 of "Auto Channel Set" on page 30.
EN TUNER SET (cont.) Delete A Channel fi Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL CH FRQ SYS CH FRQ 01 150 BG 07 229 02 165 BG 08 237 03 195 BG 09 355 04 205 BG 10 365 05 213 BG 11 374 06 221 BG 12 384 [5/∞] = [CANCEL] : DELETE [5/∞] = : EDIT [MENU] : EXIT SYS BG BG BG BG BG BG ● To re-store it, simply press PUSH JOG . ● Repeat steps 3 – 4 as necessary.
EN 3 ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL TO FINE-TUNE Press PUSH JOG %fi until the channel you want to tune begins blinking, then press OK twice. ● The "FRQ" number for that channel starts blinking. 5 FRQ 229 237 355 365 374 384 SYS BG BG BG BG BG BG Press PUSH JOG %fi until the picture becomes clearer, then press OK or PUSH JOG . ● Repeat steps 3 and 4 as necessary.
EN TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is applied to the recorder. ● The mains power cord is disconnected. Connect the mains power cord. 2. The clock is functioning properly, but the recorder cannot be powered.
EN 35 RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Recording cannot be started. ● There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed. Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. 2. TV broadcasts cannot be recorded. ● "L-1" or "F-1" has been selected as the input mode. Set to the desired channel. 3. Tape-to-tape editing is not possible.
EN TROUBLESHOOTING (cont.) OTHER PROBLEMS SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Whistling or howling is heard from the TV during camcorder recording. ● The camcorder's microphone is too close to the TV. ● The TV's volume is too high. Position the camcorder so its microphone is away from the TV. Turn the TV's volume down. 2. When scanning channels, some of them are skipped over. ● Those channels have been designated to be skipped. If you need the skipped channels, restore them. (Z pg.
QUESTIONS AND ANSWERS EN 37 PLAYBACK RECORDING Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen? A. This is normal. It reduces distortion at the pause and resume points.
EN INDEX FRONT VIEW 1 2 3 45 6 SP/LP/EP STANDBY/ON COLOUR SYSTEM VIDEO AUDIO REVIEW TV PROG SP 7 1 2 3 4 5 6 7 8 8 9 STANDBY/ON Button Z pg. 8 Cassette Loading Slot SP/LP/EP Button Z pg. 16 Rewind [REW] Button Z pg. 11, 12 PLAY Button Z pg. 11 Fast Forward [FF] Button Z pg. 11, 12 VIDEO/AUDIO Input Connectors Z pg. 27 REVIEW Button Z pg. 13 0 ! 9 0 ! @ # $ % @ # $ % COLOUR SYSTEM Button Z pg. 28 Display Panel Z pg. 39 Infrared Beam Receiving Window TV PROG +/– Buttons Z pg.
EN DISPLAY PANEL 1 2 3 4 5 6 REVIEW SP 7 1 B.E.S.T. Picture System Display Z pg. 18 2 Symbolic Mode Indicators PLAY: FF/REW VARIABLE SHUTTLE SEARCH: STILL: SLOW: RECORD: RECORD PAUSE: 8 9 3 Tape Speed Indicators Z pg. 16 4 "Timer" Indicator Z pg. 21 5 Channel Display Clock Display 6 Instant REVIEW Indicator Z pg.
EN INDEX (cont.) ^ 1 2 3 4 VCR & TV TV/VCR DISPLAY AUDIO (MONITOR) 1 2 3 4 5 6 2 5 9 C. RESET AUX CANCEL 0 START STOP TIMER DATE TV PROG EXPRESS PROGRAMMING 1 PROG. CHECK PROG. MENU TV PROG + 30 SEC 3 OK VO V O 4 L + PUSH JOG TV 8 9 0 ! @ # $ % WEEKLY 8 L V 6 7 DAILY 7 * ( ) q w e r t y u i o p T – TV P ROG – Q MULTI BRAND REMOTE CONTROL UNIT 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ^ & * ( ) q w e r t y % u i o p Q TV Button Z pg. 25 VCR Button Z pg.
SPECIFICATIONS GENERAL Power requirement Rating : Operating : Power consumption : Temperature Operating : Storage : Operating position : Dimensions (WxHxD) : Weight : Format : Maximum recording time (SP) : (LP) (EP) VIDEO/AUDIO Signal system Recording system Signal-to-noise ratio Horizontal resolution Frequency range Input/Output AC 110 – 240 V`, 50/60 Hz AC 090 – 260 V`, 50/60 Hz 18 W 5°C to 40°C –20°C to 60°C Horizontal only 400 x 94 x 275 mm 3.2 kg VHS standard 240 min.
MEMO
MEMO
EN HR-J461MS ® VICTOR COMPANY OF JAPAN, LIMITED ® Registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. COPYRIGHT © 1999 VICTOR COMPANY OF JAPAN, LTD.
