CONTENTS VIDEO CASSETTE RECORDER SAFETY FIRST HR-S6722EK QUICK SET UP GUIDE 2 Safety Precautions ............................. 2 Some Do's And Don'ts ..................... 4 5 CHECK THE CONTENTS .................. 5 INSTALLATION ................................ 6 AUTO SET UP .................................. 8 PRESET DOWNLOAD ...................... 9 T-V LINK 11 T-V Link Functions .......................... 11 SATELLITE RECEIVER CONTROL 12 Satellite Receiver Control Setting ....
SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT n Please read the various precautions on page 2 – 4 of this instruction manual before installing or operating the recorder.
CAUTION n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial. The STANDBY/ON current on and off.
SAFETY FIRST (cont.) Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
QUICK SET UP GUIDE Dear Customer, 1 CHECK THE CONTENTS CHECK ALL THE CONTENTS SHOWN BELOW Video Cassette Recorder TV TV/VCR – –:– – AUDIO 1 2 3 4 5 6 2 VPS/PDC VPS/PDC DAILY/QTDN. WEEKLY/HEBDO 7 8 0000 AUX 9 4 0 START DEBUT STOP FIN DATE PR EXPRESS 1 PROG MENU ? 30 SEC ENTER/EN TRE E 3 OK TV PR + + STEP Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder.
STEP QUICK SET UP GUIDE (cont.) 2 INSTALLATION CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. Back of TV RF Cable (provided) 21-pin SCART Cable (not provided) Aerial connector 21-pin AV input connector (SCART) Make this connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will need this cable in order to enjoy stereo playback of videotapes.
Back of TV AUDIO IN connectors S-VIDEO IN connector S-Video cable (not provided) Audio cable (not provided) Aerial connector Mains outlet Mains Power Cord Back of Recorder RF Cable (provided) S-VIDEO CONNECTION To connect to a TV with S-VIDEO/AUDIO IN connectors . . . 1– Connect the aerial, recorder and TV as per "RF CONNECTION" (Z pg. 6). 2– Connect the recorder's S OUT connector to the TV's S-VIDEO IN connector. 3– Connect the recorder's AUDIO OUT connectors to the TV's AUDIO IN connectors.
STEP 8 QUICK SET UP GUIDE (cont.) AUTO SET UP 3 SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL* The Auto Set Up function sets the tuner channels, clock, the VIDEO Plus+ assigned Guide Program numbers and the video channel* automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet. * Useful if you have connected the video recorder to your TV via RF connection (Z pg.
PRESET DOWNLOAD SET THE TUNER CHANNELS BY DOWNLOADING FROM YOUR TV, CLOCK AND GUIDE PROGRAM NUMBERS When you connect the recorder and your TV via fully-wired 21-pin SCART cable (Z pg. 6), you can set the recorder's tuner channels by downloading preset data from your TV instead of using the Auto Set Up function (Z pg. 8). After downloading is completed, the recorder sets the clock and the VIDEO Plus+ assigned Guide Program numbers automatically. For details, refer to the instruction manual for your TV.
QUICK SET UP GUIDE (cont.) Auto Set Up/Preset Download results appear on the display panel A When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed after the OK button is pressed in item 3 on page 8 or after performing item 1 on page 9. B When auto channel set has been completed successfully but auto clock set has not, "(PR)1" will be displayed after the OK button is pressed in item 3 on page 8 or after performing item 1 on page 9.
T-V LINK T-V Link Functions When you connect the recorder and your TV via a fully-wired 21-pin SCART cable (Z pg. 6), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual for your TV. * Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fullywired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.
SATELLITE RECEIVER CONTROL Installing Satellite Controller Satellite Receiver 1 Control Setting The following procedure is required if you receive satellite channels through a satellite receiver. Around 20 seconds before VIDEO Plus+ timer recording (Z pg. 18) or Express timer programming (Z pg. 20) starts, the recorder sets its input mode to "L-2" and automatically switches the satellite receiver’s channels using the provided Satellite Controller.
1 3 2 2 NUMBER 4 5 6 7 8 9 4 0 1 MENU Press %fi to move the highlight bar (pointer) to “SAT CONTROL SET”, then press OK or #.
BASIC OPERATIONS The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Playback Turn on the TV and select the VIDEO channel (or AV mode).
Variable-Speed Search NOTE: Refer to the SHUTTLE ring illustration below as you read the following procedures. s Slow motio n y Pl a PAUSE DURING PLAYBACK Press PAUSE. If there is vertical jitter, use the PR buttons to correct the picture. ACTIVATE FRAME-BY-FRAME PLAYBACK Turn the JOG dial to the right for forward frame-byframe playback, or to the left for reverse frame-by-frame playback. OR Press PAUSE. Each time PAUSE is pressed the tape will advance one frame. OR Press @ or #.
BASIC OPERATIONS (cont.) TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. Recording Turn on the TV and select the VIDEO channel (or AV mode). PLAY 5 1 1 RE CO SP/LP RD PR +/ – T 4 EC EJ P/ O 2 PAUSE ST 5 4 – –:– – 2 NUMBER 2 3 4 5 6 7 8 9 Insert a cassette with the record safety tab intact (See below).
Record One Programme While Watching Another 1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view. ● The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's PR buttons is recorded on the tape. RE CO RD PR+/– SELECT PRESET TO WATCH Elapsed Recording Time Indication You can check the exact time of a recording.
BASIC OPERATIONS (cont.) With the VIDEO Plus+ system, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. VIDEO Plus+ Timer 1 Programming ACCESS VIDEO PLUS+ SCREEN Press PROG. VIDEO PLUS+ [0 – 9] = VIDEO PLUS+ [+/–] : EXPRESS PROGRAMING [PROG] : EXIT Before performing the VIDEO Plus+ Timer Programming: ● Make sure that the recorder's built-in clock is set properly.
4 5 SET TAPE SPEED Press SP/LP ( ) to set the tape speed. SET PDC MODE Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON. If "VPS/PDC OFF" is displayed on the screen or "VPS/ PDC" is not lit on the display panel, PDC is set to OFF. Z "PDC Recording" in the column below. ● VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.
BASIC OPERATIONS (cont.) Express Timer Programming Before performing Express Timer Programming: ● Make sure that the recorder's built-in clock is set properly. ● Insert a cassette with the safety tab in place. The recorder will come on automatically. ● Turn on the TV and select the VIDEO channel (or AV mode). If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme.
6 ENTER PRESET POSITION Press PR +/– to enter the preset position corresponding to the broadcasting station you wish to record. – P1 – START 21:00 SP DATE 25.12 [+/–] = [PROG] : EXIT STOP 22:00 = VPS/PDC OFF TV PROG 1 BBC 1 [0]:SAT SP 7 8 ) to set the tape speed. SET PDC MODE Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON.
BASIC OPERATIONS (cont.) Check, Cancel And Replace Programmes 1 – –:– – 1 3 2 2 PDC 4 5 6 7 8 9 2 4 0 DISENGAGE TIMER MODE Press ‰, then press . ACCESS PROGRAMME CHECK SCREEN/DISPLAY Press . START STOP CH DATE 1 8 : 00 10 : 00 3 24 . 12 2 10 : 00 10 : 45 2 25 . 12 3 11 : 30 13 : 00 1 25 . 12 4 5 6 7 8 PR+/– START+/– [ AT ? ] : NEXT E+ /– ST O P+ /– D 1 P /L SP 3 OK 3 ACCESS PROGRAMME SCREEN/ DISPLAY Press again to check more information.
When programmes overlap each other If "PROGRAM OVERLAPPED" appears, you have another programme overlapping the programme you have just made. The Program Check screen appears and conflicting programmes will start blinking. – –:– – 1 2 3 4 5 6 8 9 START+/– ? [ [5∞] = [PROG] : EXIT 4 PR+/– 1 START 1 8 : 00 2 10 : 00 3 11 : 30 4 9 : 00 5 6 7 8 E+ /– AT 0 D 7 STOP+/– 2 START STOP CH DATE 1 8 : 00 10 : 00 3 24 . 12 2 10PROGRAM : 00 10 : 45 2 25 . 12 OVERLAPPED 3 11 : 30 13 : 00 1 25 .
ADVANCED OPERATIONS Playback Picture Adjustment Manual Tracking Your video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments. This is usually only associated with old or worn tapes or recordings made on old or worn recorders.
Selecting The Sound You Want – –:– – 1 2 4 5 6 7 8 9 Your recorder is equipped with a Digital stereo sound decoder (NICAM), making reception of stereo and bilingual broadcasts possible. When the recorder is tuned to a different station, the type of broadcast being received will be displayed on the TV screen for a few seconds.
ADVANCED OPERATIONS (cont.) Looking For The Scene You Want Index Search Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode. 1 – –:– – REVIEW 1 2 3 4 5 6 7 8 9 £ 2 2 4 ACTIVATE INDEX SEARCH Press @ or # (™ or £). “™ 1” or “£ 1” is displayed on screen and search begins in the corresponding direction.
Recording According To Tape Type Turn on the TV and select the VIDEO channel (or AV mode). Super VHS ET (S-VHS ET) — Recording on VHS tapes with S-VHS quality This function allows you to record in SP mode on VHS tapes with S-VHS picture quality. Tapes recorded using this function can be played back on a recorder equipped with the S-VHS ET function. ● You can activate this function only before you start recording on a VHS tape. ● Before recording, make sure that "B.E.S.T." is set to "ON". (Z pg.
ADVANCED OPERATIONS (cont.) Playback/ Recording According To Tape Characteristics The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”. 1 2 PLAY Turn on the TV and select the VIDEO channel (or AV mode). B.E.S.T. Picture System 3 Press . ACCESS MAIN MENU SCREEN Press MENU.
Recording 1 START RECORDING Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE ● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. NOTES: ● The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. ● The B.E.S.T.
ADVANCED OPERATIONS (cont.) Automatic Satellite Programme Recording This facility allows you to record automatically a satellite programme which is timer-programmed on your external satellite receiver.
1 SA P /L SP T Before performing the following steps: ● Make sure the satellite receiver is connected to the recorder's AV2 (L-2) IN/DECODER connector. (Z pg. 30) ● Programme the timer on the satellite receiver. ● Insert a cassette with the safety tab in place. ATTENTION ● Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.
ADVANCED OPERATIONS (cont.) Minimizing Picture Degradation While Editing Turn on the TV and select the VIDEO channel (or AV mode). 3 2 This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO." 1 2 3 – –:– – 1 Picture Control 2 4 5 6 7 8 9 4 0 1 MENU ? 3 ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Move the highlighted bar (pointer) to "MODE SET" by pressing %fi, then press OK or #.
Edit From A Camcorder You can use a camcorder as the source player and your video recorder as the recorder. 1 2 3 2 2 4 5 6 7 8 9 4 0 AUX PR 1 A If the camcorder has no S-VIDEO output connector... ... connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder’s front panel AUDIO/ VIDEO input connectors. B If the camcorder has an S-VIDEO output connector... ...
ADVANCED OPERATIONS (cont.) You can use your video recorder as the source player or as the recording deck. Edit To Or From Another 1 Video Recorder 2 3 4 5 6 7 8 9 2 4 0 AUX PR 1 Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated on page 35. A When Using Your Video Recorder As The Source Player ... ... connect its AV1 (L-1) IN/OUT connector to the recording deck. B When Using Your Video Recorder As The Recording Deck ... ...
A B TV Receiver VIDEO CHANNEL or AV mode Player Your recorder 21-pin SCART Cable (not provided) Recorder Your recorder 21-pin SCART Cable (not provided) RF Cable (provided) Another recorder RF Cable (provided) TV Receiver VIDEO CHANNEL or AV mode Another recorder Player Recorder C TV Receiver Recorder Your recorder S-Video Cable (not provided) 21-pin SCART Cable (not provided) Another recorder Player NOTES: ● All necessary cables can be obtained from your dealer.
ADVANCED OPERATIONS (cont.) L-1 OUTPUT/INPUT Setting The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-1 OUTPUT" and "L-1 INPUT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 (L-1) IN/OUT connector of this recorder. 1 Press MENU to access the Main Menu screen.
On-Screen Display Other Functions You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. Turn on the TV and select the VIDEO channel (or AV mode). 2 – –:– – 1 1 3 2 2 4 5 6 7 8 9 3 4 0 ? 1 3 MENU 4 OK ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or #.
ADVANCED OPERATIONS (cont.) Power Save Mode You can reduce the power consumption while the recorder is turned off. – –:– – 1 2 3 4 5 6 7 8 9 1 2 2 4 0 1 ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #.
Auto SP→LP Timer Auto Timer When "AUTO TIMER" is set to "ON" the timer is automatically engaged when the recorder power is turned off and automatically disengaged when the recorder is powered back on. 1 2 ACCESS MAIN MENU SCREEN 4 Approximately 150 minutes Approximately 60 minutes SP mode LP mode Press MENU. Total 210 minutes ACCESS MODE SET SCREEN Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #.
ADVANCED OPERATIONS (cont.) Repeat Playback Your video recorder can automatically play back the whole tape 100 times repeatedly. – –:– – 1 3 2 1 2 2 4 5 6 7 8 9 4 0 PL AY 1 ? FF REW PAUSE STOP 3 3 START PLAYBACK Press PLAY. ACTIVATE REPEAT PLAYBACK Press PLAY and hold for over 5 seconds, then release. ● The Play indicator ( ) on the display panel blinks slowly. ● The tape plays 100 times automatically, and then stops. STOP PLAYBACK Press STOP at any time to stop playback.
SYSTEM CONNECTIONS Connection To A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
SUBSIDIARY SETTINGS IMPORTANT Clock Set Turn on the TV and select the VIDEO channel (or AV mode). If you performed Auto Set Up (Z pg. 8), Preset Download (Z pg. 9) or Auto Channel Set (Z pg. 46), without ever having set the clock previously, the recorder's built-in clock is also set automatically. Perform the following steps only if — — Auto Clock Set has not been performed correctly by Auto Set Up, Preset Download or Auto Channel Set. or — the recorder's memory backup has expired.
VIDEO Plus+ Setup IMPORTANT Normally, Auto Set Up (Z pg. 8), Preset Download (Z pg. 9) or Auto Channel Set (Z pg. 46) sets the Guide Program Numbers automatically. You need to set the Guide Program Numbers manually only in the following cases. ● When timer-programming with the VIDEO Plus+ system, the preset position, where the station you wish to record is received on your recorder, is not selected or when you add a channel after Auto Set Up or Auto Channel Set has taken place.
SUBSIDIARY SETTINGS (cont.) IMPORTANT Video Channel Set Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. Perform the following steps only if — — Video Channel Set has not been done correctly by the Auto Set Up function (Z pg. 8). — interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.
With RF Connection Before performing the following procedure, make sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder. n the connected TV is turned on. n batteries have been installed in the remote control. O ST P 1 – –:– – 1 2 3 4 5 6 7 8 9 2 2 ACCESS VIDEO CHANNEL SET MODE Press and hold down STOP on the recorder until the display panel shows the following.
SUBSIDIARY SETTINGS (cont.) IMPORTANT Tuner Set Turn on the TV and select the VIDEO channel (or AV mode). Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up function (Z pg. 8) or Preset Download (Z pg. 9). — you have moved to a different area or if a new station starts broadcasting in your area. Your recorder needs to memorise all necessary stations in preset positions in order to record TV programmes.
4 2 3 4 5 6 7 8 9 5 1 2 4 0 1 After "SCAN COMPLETED" PR CH ID PR CH ID is displayed on the screen 01 26 BBC1 08 –––– 02 33 BBC2 09 –––– for about 5 seconds, a 03 23 ITV 10 –––– Confirmation screen 04 30 CH4 11 –––– –––– looking like the one on the 05 37 CH5 12 06 –––– 13 –––– right appears. The stations 07 –––– 14 –––– [5∞ ] your recorder located : EDIT = appear on a Confirmation = [X] : DELETE screen — preset positions [MENU] : EXIT (PR), channels (CH) and station names (ID – Z pg. 51).
SUBSIDIARY SETTINGS (cont.) 4 – –:– – 3 4 5 6 7 8 9 [5∞] : SELECT [ ] : CURSOR += : OK [MENU] : EXIT 2 NUMBER The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each. 4 0 5 ? INPUT CHANNEL Press the NUMBER keys to input the channel number you want to store. PR CH ID FINE DECODER 06 CH21 – –␣ – – +/– OFF ● To input the registered station name (ID – Z [5∞] : SELECT pg.
Perform steps 1 and 2 of "Storing Channels Manually" on page 48 to access the Confirmation screen before continuing. 1 2 3 SELECT ITEM Press %fi @ # until the item you want to delete begins blinking. DELETE CHANNEL Press . ● The item directly beneath the cancelled one moves up one line. ● Repeat steps 1 and 2 as necessary. CLOSE CONFIRMATION SCREEN Change Station Preset Position Perform steps 1 and 2 of "Storing Channels Manually" on page 48 to access the Confirmation screen before continuing.
SUBSIDIARY SETTINGS (cont.) Set Stations (A) Set Stations (B) Set station names that are registered in your recorder. Set station names other than the ones registered in your recorder. Perform steps 1 and 2 of "Storing Channels Manually" on page 48 to access the Confirmation screen before continuing. 5 1 Press # until the first letter of the station name begins blinking.
TV Station And ID List STATION NAME ID* STATION NAME ID* Anglia TV ARD ARTE BBC Group BBC1 BBC2 Berlin 1 Berlin 2 Border TV Bayern1 Bayern3 BRT1 BRT2 Children Ch Canal + CNN Channel TV Central TV Channel 4 Channel 5 DRS DR TV DSF Euronews Euronews Eurosports France1 France2 France3 Granada TV Grampian TV Hessen1 Hessen3 HRT HTV ITV Network Kabelkanal London MDR MTV Nord3 NDR1 NDR3 NED1 NED2 NED3 Network 2 NRK N-TV Offener Kanal ORF1 ORF2 ORF3 OWL 3 Premiere PR07 RAI1 RAI2 RAI3 RB1 RB3 Rikisutvarpid-S
SUBSIDIARY SETTINGS (cont.) TV Station Channel Number Guide For customers in the U.K. Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV. BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill ......................... Crystal Palace ....................... Dover ................................... Heathfield ............................ Oxford .................................
SUBSIDIARY INFORMATION Questions And Answers PLAYBACK RECORDING Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen? A. This is normal. It reduces distortion at the pause and resume points.
SUBSIDIARY INFORMATION (cont.) Troubleshooting Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE 1. No power is applied to the recorder. ● The mains power cord is disconnected. Connect the mains power cord. CORRECTIVE ACTION 2.
3. Tape-to-tape editing is not possible. 4. Camcorder recording is not possible. ● The source (another video recorder, camcorder) has not been properly connected. ● All necessary power switches have not been turned on. ● The input mode is not correct. Confirm that the source is properly connected. ● The camcorder has not been properly connected. ● The input mode is not correct. Confirm that the camcorder is properly connected. Set the input mode to “L-1”,“L-2”, “F-1” or “S-1”.
SUBSIDIARY INFORMATION (cont.) Index FRONT VIEW 1 4 23 5 6 7 VPS/PDC 8 90! @ #$ % ^ &* () q * Attach the provided connector cover when you do not use the front panel connectors. 1 STANDBY/ON Button turns recorder on/off (loading a cassette also turns power on). 2 ‰ (TIMER) Button engages timer-standby mode. Z pg. 19, 21 3 REVIEW Button "reviews" timer-recorded programme. Z pg.
REAR VIEW 1 2 3 5 6 1 Mains Power Cord supplies power to recorder. Z pg. 6 2 S OUT Connector enables S-VIDEO connection to TV or second recorder. Z pg. 7, 34 3 AV1 (L-1) IN/OUT Connector enables AV connection to TV or second recorder; input recordable when "L-1" selected. Z pg. 6, 34 4 ANT. IN Connector enables connection of aerial. Z pg. 6 5 AUDIO OUT (L/R) Connectors enable connection of audio cassette recorder, TV or second video recorder for dubbing. Z pg.
SUBSIDIARY INFORMATION (cont.) REMOTE CONTROL 1 2 3 4 5 6 7 8 TV TV/VCR – –:– – AUDIO 1 2 3 4 5 6 2 VPS/PDC DAILY/QTDN. WEEKLY/HEBDO 7 8 0000 AUX 9 4 0 START DEBUT STOP FIN DATE PR EXPRESS MENU ? 30 SEC ENTER/EN TRE E 3 OK 6 7 8 9 0 + TV PR + * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. TV 9 0 ! @ # $ % 1 PROG ^ & * ( ) q w e r t y u i o p 1 TV Button enables remote control of connected TV.
^ STANDBY/ON Button — same as button on recorder. & AUDIO Button changes output sound mode. Z pg. 25 (TV Muting) Button mutes sound of connected TV. Z "Operating JVC TVs" in the right column. * – –:– – (Display) Button — same as button on recorder. Z pg. 17 ( DAILY Button enables timer recording of daily serials. Z pg. 19, 21 ) WEEKLY Button enables timer recording of weekly serials. Z pg. 19, 21 q AUX Button selects recorder's auxiliary input mode. Z pg.
SPECIFICATIONS GENERAL Power requirement : AC 220 V – 240 V`, 50 Hz/60 Hz VIDEO/AUDIO Signal system Recording system Signal-to-noise ratio Horizontal resolution Frequency range Input/Output : PAL-type colour signal and CCIR monochrome signal, 625 lines/50 fields : DA4 (Double Azimuth) helical scan system : 45 dB : 250 lines (VHS) 400 lines (S-VHS) : 70 Hz to 10,000 Hz (Normal audio) 20 Hz to 20,000 Hz (Hi-Fi audio) : 21-pin SCART connectors (IN/OUT x 1, IN/DECODER x 1) RCA connectors (VIDEO IN x 1, AUDI
