HV-32/28D40BK / LCT1596-001A-U / All Cover LCT1596-001A-U_Cover.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 2 Wednesday, April 21, 2004 1:17 PM Warning DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor or consult your dealer.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 3 Wednesday, April 21, 2004 1:17 PM How to move the TV When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful not to trap your hands when putting the TV down.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 4 Wednesday, April 21, 2004 1:17 PM Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: • Operate only from the power source specified (AC 220 – 240 V, 50 Hz) on the unit. • Avoid damaging the AC plug and power cord.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 5 Wednesday, April 21, 2004 1:17 PM Digital terrestrial broadcasting (DVB-T) service area Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting, depending on the area in which you live, you may not be able to receive Digital terrestrial broadcasting (DVB-T). For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW website etc.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 6 Wednesday, April 21, 2004 1:17 PM CONTENTS Setting up your TV ...................................7 PICTURE menu ...................................... 29 Connecting the aerial ................................. 7 Connecting the power cord to the AC outlet....................................................... 8 Putting the batteries into the remote control..................................................... 8 Initial settings ........
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 7 Wednesday, April 21, 2004 1:17 PM Setting up your TV Caution • Turn off all the equipment including the TV before connecting anything. Connecting the aerial • The connecting cables are not provided. • For further details, refer to the manuals provided with the devices to be connected. If you connect via a device with an antenna terminal such as a VCR, follow A → B → C in the diagram opposite.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 8 Wednesday, April 21, 2004 1:17 PM Setting up your TV Rear Panel Putting the batteries into the remote control Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 9 Friday, April 23, 2004 11:20 AM Setting up your TV 1 Press the main power button on the TV The power lamp lights green and the JVC logo appears. When the Automatic Search has finished, the EDIT PR LIST menu appears 1 EDIT PR LIST BBC ONE 1. BBC ONE 2. BBC TWO 7. BBC THREE 30. CBBC Channel 40. BBC NEWS 24 51. BBCi Select Main power button Power lamp Delete Select function Edit Name Select PR Lock OK Favourites Watch PR More..
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 10 Friday, April 23, 2004 1:32 PM Setting up your TV After the AUTO PROGRAM has finished, the EDIT menu appears > EDIT PR AV 01 02 03 04 05 06 07 08 09 ID CH BBC1 BBC2 ITV CH4 CH5 CH CH CH CH CH CH CH CH CH 21 22 23 24 25 26 27 28 29 ID OK MANUAL MOVE INSERT DELETE D0038-EK • If you want to, you can now edit the programme numbers (PR) using the EDIT/MANUAL function. For details, see “EDIT/MANUAL (Analogue)” on page 36.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 11 Wednesday, April 21, 2004 1:17 PM Setting up your TV Downloading the data to VCR You can transmit to the latest Analogue terrestrial broadcasting Programme numbers (PR) data to a VCR with the T-V LINK function. Caution • This only works when a T-V LINK compatible VCR is connected to the EXT-2 terminal. • This only works when the T-V LINK menu is being displayed.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 12 Wednesday, April 21, 2004 1:17 PM Setting up your TV Direct Rec “What You See Is What You Record” When the VCR is not ready, the following messages are displayed. You can easily record to VCR the images that you are watching on the TV. ERROR MESSAGE Cause and countermeasure For details, read the manual for your VCR. Use your VCR controls. “DEVICE IS RECORDING” is displayed. NO RECORDING The VCR is not able to record.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 13 Wednesday, April 21, 2004 1:17 PM TV buttons and functions Turn the main power on Press the main power button on the TV. The power lamp lights red and your TV is in standby mode. • If the power lamp lights green, the TV is already on. To turn the main power off: Press the main power button again. The power lamp goes off. Caution • The main power button on the TV does not fully isolate the TV from the AC supply.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 14 Wednesday, April 21, 2004 1:17 PM TV buttons and functions Adjust the volume 1 Press the r (Volume) button once The volume level indicator appears.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 16 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions Choose a TV channel and watch images from external devices • If the picture is tilted, correct it. See “PICTURE TILT” on page 40. Switching between Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting. Press the TV/DTV button. The broadcasting is switched every time the button is pressed.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 17 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions To use the programme number PR 0 (AV): When the TV and VCR are connected only by the aerial cable, choosing the programme number PR 0 (AV) allows you to view images from the VCR. Set the VCR RF channel to the programme number PR 0 (AV) manually. For details, see “EDIT/ MANUAL (Analogue)” on page 36.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 18 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions Channel number display: The channel number and channel name (when the channel name is registered) of the programme you are watching or the EXT terminal number is displayed. Time display: The current time of the teletext data is displayed. If the TV has not received a TV channel that has teletext programmes since it was turned on, the time display is blank.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 19 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions 14:9 ZOOM: This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen. Choose the ZOOM mode 1 Press the c button to display the ZOOM menu ZOOM 16:9 ZOOM: This zooms up the wide picture (16:9 aspect ratio) to the full screen.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 20 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions 3D CINEMA SOUND function You can enjoy sounds with a wider ambience. • This function does not work for the sound from headphones. Press the 3 button and choose “ON”, “MONO” or “OFF”. ON: Choose to add the 3D CINEMA SOUND effect to stereo sound. MONO: Choose to add the 3D CINEMA SOUND effect to mono sound. OFF: Choose to cancel the 3D CINEMA SOUND effect.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 21 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions • Choose the main-picture channel by pressing the p p buttons. Choose the sub-picture channel by pressing the p buttons. • You cannot use the g (swap) button. When watching Digital terrestrial broadcasting (DVB-T), the mainpicture and sub-picture cannot be switched. • 1125i, 625p, and 525p signal pictures cannot be displayed as the sub-picture.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 22 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions • • • • • • - The pictures cannot be swapped when a picture of 625p or 525p signal from EXT-4 is being displayed as the main picture. Do not press the g (swap) button while you are recording the TV output on the VCR. If you do, the TV output signal will change. You cannot view a scrambled channel in the sub-picture.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 23 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions Pressing the h (Information) button to display the help screen. Press it again to return to the guide screen. 1 BBC ONE 13:12 Electronic Programme Guide The Rugby World Cu...
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 24 Wednesday, April 21, 2004 1:17 PM Remote control buttons and functions Displaying the Subtitles • Use this function when watching Digital terrestrial broadcasting (DVB-T). With Digital terrestrial broadcasting (DVBT), some programmes are broadcast with subtitles. Subtitles can be displayed when watching these programmes.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 25 Wednesday, April 21, 2004 1:17 PM Teletext function 1 Press the g button The digital teletext information appears.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 26 Wednesday, April 21, 2004 1:17 PM Teletext function When watching Analogue terrestrial broadcasting: Basic operation (Analogue) You can view two types of teletext broadcasts on the TV: FLOF (Fastext) and WST. Using the List Mode You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 27 Wednesday, April 21, 2004 1:17 PM Teletext function Hold Size You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being received. Press the C (Hold) button You can double the height of the teletext display. Press the F (Size) button Hold indication To cancel the Hold function: Press C (Hold) button again.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 28 Wednesday, April 21, 2004 1:17 PM Using the TV’s menu This TV has a number of functions you can operate using menus. To use all your TV’s functions, you need to understand the basic menu operating techniques fully.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 29 Wednesday, April 21, 2004 1:17 PM PICTURE menu COLOUR PICTURE PICTURE MODE CONTRAST BRIGHT SHARP COLOUR HUE COLOUR TEMP. FEATURES STANDARD COOL RESET OK D0014-EN • While the PICTURE menu is displayed, pressing the blue button will set the CONTRAST, BRIGHT, SHARP, COLOUR, HUE settings to their default settings. You can adjust the picture colour. 2 : lighter 3 : deeper HUE You can adjust the picture tint.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 30 Wednesday, April 21, 2004 1:17 PM PICTURE menu FEATURES Choose FEATURES and press the a or 3 button to display the sub-menu. > FEATURES DIGITAL VNR Super DigiPure MOVIE THEATRE Colour DigiPure COLOUR SYSTEM 4:3 AUTO ASPECT AUTO(LOW) AUTO AUTO ON MAX: The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO(HIGH) but still notice some noise, change the setting from AUTO(HIGH) to MAX.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 31 Wednesday, April 21, 2004 1:17 PM PICTURE menu MIN: The level of DigiPure effect is set to the minimum. When you set the Super DigiPure function to AUTO and notice some noise, change the setting from AUTO to MIN. • The MIN setting is not suitable for highquality pictures which contain very little noise. MAX: The level of DigiPure effect is set to the maximum.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 32 Wednesday, April 21, 2004 1:17 PM PICTURE menu AUTO: This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or an EXT terminal. • The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 33 Wednesday, April 21, 2004 1:17 PM SOUND menu SOUND STEREO/ BASS TREBLE BALANCE HEADPHONE VOLUME 3D CINEMA SOUND OK BALANCE You can adjust the volume balance between the left and right speaker. 2 : turn the left speaker’s volume level up. 3 : turn the right speaker’s volume level up. HEADPHONE VOLUME D0019-EN • Functions in the “SOUND” menu other than “HEADPHONE VOLUME” work for the TV speakers.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 34 Wednesday, April 21, 2004 1:17 PM FEATURES menu FEATURES SLEEP TIMER CHILD LOCK APPEARANCE BLUE BACK TYPE A ON To cancel the SLEEP TIMER function: Press the 2 button to set the period of time to “OFF”. CHILD LOCK OK D0023-EN • CHILD LOCK, APPEARANCE and BLUE BACK cannot be chosen when watching Digital terrestrial broadcasting (DVB-T). SLEEP TIMER You can set the TV to automatically turn off after a set period of time.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 35 Wednesday, April 21, 2004 1:17 PM FEATURES menu 4 Press the 6 buttons to choose a TV channel Every time you press the 6 buttons, the Programme number (PR) changes, and the picture of the TV channel registered in the Programme number (PR) is displayed on the screen. 5 Press the blue button and set the CHILD LOCK function. Then press the a button n (CHILD LOCK) appears and the TV channel is locked.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 36 Wednesday, April 21, 2004 1:17 PM SET UP menu EDIT/MANUAL (Analogue) SET UP AUTO PROGRAM EDIT/MANUAL PICTURE TILT DECODER(EXT-2) EXT SETTING ATTENUATOR OFF OFF OK D0029-EN • AUTO PROGRAM, EDIT/MANUAL, PICTURE TILT and DECODER (EXT-2) cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 37 Wednesday, April 21, 2004 1:17 PM SET UP menu Basic operation 1 Choose EDIT/MANUAL, then press the a or 3 button The EDIT menu appears.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 38 Wednesday, April 21, 2004 1:17 PM SET UP menu DELETE 1 Press the 6 buttons to choose a TV channel Every time you press the 6 buttons, the programme number (PR) changes and the picture of the TV channel stored in the programme number (PR) appears on the screen. 2 Press the yellow button to delete the TV channel The TV channel is deleted from the programme numbers (PR) list.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 40 Wednesday, April 21, 2004 1:17 PM SET UP menu CH NUMBER • When you want to use the INSERT function on page 39, find the CH/CC number corresponding to the channel number of the TV channel from this table. If you want to know a particular TV channel’s channel menu, look in TV listings magazines or contact the broadcaster.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 41 Wednesday, April 21, 2004 1:17 PM SET UP menu DECODER (EXT-2) If you have a decoder connected to a T-V LINK compatible VCR, which in turn is connected to the EXT-2 terminal, use the DECODER (EXT-2) function to unscramble the scrambled TV channels. 1 Turn on the decoder power 2 Display the scrambled TV channel on the TV Even if the decoder is working, a scrambled picture appears.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 42 Wednesday, April 21, 2004 1:17 PM SET UP menu 1 Press the 5 or 6 buttons to choose an EXT terminal EXT SETTING 1 Choose EXT SETTING, then press the a or 3 button The EXT SETTING menu appears.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 43 Wednesday, April 21, 2004 1:17 PM SET UP menu ID LIST DUBBING You can store a name for each of the devices connected to each EXT terminal. Giving a name to an EXT terminal makes the EXT terminal number appear on the screen, together with its name.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 44 Wednesday, April 21, 2004 1:17 PM SET UP menu TV: The picture and sound of the Analogue terrestrial broadcasting TV channel you are currently viewing are output from the EXT-2 terminal. DTV: The picture and sound of the Digital terrestrial broadcasting (DVB-T) TV channel you are currently viewing are output from the EXT-2 terminal. • During dubbing, you cannot turn off the TV.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 45 Wednesday, April 21, 2004 1:17 PM DTV menu DTV Timers Configuration Edit PR List Installation Common Interface D0209-EN • DTV in the menu bar can only be chosen when watching Digital terrestrial broadcasting (DVB-T). 1 Choose Timers and press the a button The TIMER menu appears. TIMER MENU No.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 46 Wednesday, April 21, 2004 1:17 PM DTV menu End: Set the timer end time with the number buttons. • When the 5 buttons are pressed, the input position moves. Press the 4 button. Date: Set the date for the timer to work with the number buttons. • When the 5 buttons are pressed, the input position moves. Press the 4 button. Mode: Use the 5 buttons to choose the timer mode (Once/Daily/Weekly), and then press the a button.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 47 Wednesday, April 21, 2004 1:17 PM DTV menu Reactivating the cancelled timer setting Display the TIMER MENU and press the 6 buttons to choose which timer setting to reactivate. Press the 5 buttons so that “Active” appears in the Mode column. Aborting the timer recording Display the Digital terrestrial broadcasting (DVB-T) channel picture on the screen and press the h (Information) button.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 48 Wednesday, April 21, 2004 1:17 PM DTV menu On: The Edit PR List Favourites settings are enabled. When the p p button is pressed, only the channels chosen in the Edit PR List Favourites (those with the icon) can be chosen. • For details on how to set your favourite channels, see “Setting the favourite channels” on page 51.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 49 Friday, April 23, 2004 11:20 AM DTV menu Enter PIN code Choose Enter PIN code to change the PIN code for the Edit PR List menu’s “Lock”. The PIN code factory setting (how it is set when you purchase the television) is 0000. 1 Press the 6 buttons and choose Enter PIN code, then press a button 2 Input the current PIN code When you are making this setting for the first time, input 0000.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 50 Friday, April 23, 2004 11:57 AM DTV menu • When the b button is pressed, the previous screen is returned to. When the TV/DTV or H buttons are pressed, the menu disappears. • When the h (Information) button is pressed, the help screen appears. When it is pressed again, the previous screen is returned to. Choosing a channel The chosen channel is shown on the quarterscreen. 3 Choose Yes and press the a button The chosen channel is deleted.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 51 Friday, April 23, 2004 11:20 AM DTV menu Locking a channel Digital terrestrial broadcasting (DVB-T) channels can be locked in the same way as the FEATURES menu CHILD LOCK. 1 Press the 5 buttons and choose Lock on the bar at the bottom of the screen 2 Press the 6 buttons and choose the channel to be locked, and then press the a button The Enter PIN code input window appears. 2 EDIT PR LIST BBC TWO 1. BBC ONE 2. BBC TWO 7. BBC THREE 30.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 52 Wednesday, April 21, 2004 1:17 PM DTV menu Installation Use when re-registering a channel or when registering a new channel. 1 Choose Installation and press the a button The Installation menu appears. Installation Automatic Search Manual Search Factory Settings Factory Settings: Choose when you have moved house etc and want to automatically re-register all the channels.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH Body_Eng.fm Page 54 Friday, April 23, 2004 9:41 AM Additional preparation Equipment which can output the S-VIDEO signal (Y/C signal) Connect the equipment to an EXT terminal (but not the EXT-1 terminal). You can choose between an S-VIDEO signal (Y/C signal) and a regular video signal (composite signal). For details of how to operate the equipment, see “S-IN (S-VIDEO input)” on page 42.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 55 Wednesday, April 21, 2004 1:17 PM Additional preparation Connecting speakers/amplifier While referring to the audio equipment connection diagram, connect the audio equipment you want to the TV. You can use external front speakers to listen to the TV sound instead of the TV speakers. Before connecting anything: • Read the manuals provided with the amplifier and speakers. • Turn the TV and amplifier off.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 56 Wednesday, April 21, 2004 1:17 PM Troubleshooting Digital terrestrial broadcasting (DVB-T) service area Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting, depending on the area in which you live, you may not be able to receive Digital terrestrial broadcasting (DVB-T).
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 57 Wednesday, April 21, 2004 1:17 PM Troubleshooting • Have the COLOUR and BRIGHT settings been adjusted properly? Follow the description “BRIGHT” and “COLOUR” on page 29 to try to adjust them properly. • Videotaping teletext is not recommended because it may not record correctly. • When a white and bright still image (such as a white dress) is displayed on the screen, the white part may look as if it is coloured.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.book Page 58 Wednesday, April 21, 2004 1:17 PM Troubleshooting • The TV may make a crackling sound due to a sudden change in temperature. The picture or sound may be normal. If you hear crackling sounds frequently while you are viewing the TV, there may be other causes. As a precaution, ask your service technician to inspect it. • Touching the screen may cause you to feel a slight electric shock due to its static electricity.
HV-32/28D40BK / LCT1596-001A-U / ENGLISH HV-32&28D40BK_Eng.
HV-32/28D40BK / LCT1596-001A-U / All Cover HV-32&28D40BK_Eng.
