Color profile: Disabled Composite Default screen ENGLISH CASTELLANO LT-20DJ5SSP INTEGRATED DIGITAL LCD PANEL TV TV CON PANEL LCD DIGITAL INTEGRADO INSTRUCTIONS MANUAL DE INSTRUCCIONES D Digital Video Broadcasting Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) Number: 4085 50087315 ©2006 Victor Company of Japan, Limited 0506TKH-VT-VT D:\IB Guncel\JVC IDTV 20710 (RM-C1897S UK)\LT-20DJ5SSP-17MB16P-10041702\COVER-ENG-ESP-20710-17MB16P-C1897S UK-(LT-20DJ5SSP)-(TVAVOK)-IDTV-100417
Contents For your safety ......................................... 2 Where to install ....................................... 5 Important Information ............................. 6 Control Panel Buttons ............................. 7 Using the stand ........................................ 8 Remote Control Buttons .......................... 9 Features ................................................. 10 Getting Started ........................................ 11 T-V LINK ..................................
For your safety This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety. They are of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have just purchased.
DONT continue to operate the equipment if you are in any doubt about it working normally, or it is damaged in any way switch off, withdraw the mains plug and consult your dealer. DONT put the empty batteries into garbage instead of recycle bin to reduce harmfull effects to the environment. ABOVE ALL NEVER let anyone, especially children, push anything into holes, slots or any other openings in the case this could result in a fatal electric shock.
WARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down. Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV. Doing so may cause the TV to fall over and lead to injuries.
Where to install WARNING When you install the TV on the wall, only use a JVC wall mounting unit which is designed for this TV. Make sure the TV is installed on the wall by a skilled installer. Locate the TV away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing.
Important Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused by: fire; earthquake; accidental damage; intentional misuse of the product; use of the product in improper conditions; loss and/or damage caused to the product whilst in the possession of a third party; any damage or loss caused as a result of the owner s failure and/or neglect to follow the instructions set out in the owners manual; any loss or da
Control Panel Buttons 32:(5 /$03 ,1)5$5(' 5(&(,9(5 63($.(5 63($.(5 352*5$0 )227 723 &29(5 With certain combinations of connectors and leads the back cover may not be easily fitted. If the cover is left off, this in no way infringes safety requirements. -701-ENG-20710-17MB16P-C1897S UK-(LT-20DJ5SSP)-(TVAVOK)-IDTV-10041702-50087315.p65 7 07.06.
Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen 10° backward and 5° forward. Tilt the TV up and down: While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down. -801-ENG-20710-17MB16P-C1897S UK-(LT-20DJ5SSP)-(TVAVOK)-IDTV-10041702-50087315.p65 8 07.06.
Remote Control Buttons / I = (Stand By) button TV / VCR / DVD Switch 9'' Number buttons 79 AV button (EXT-1, EXT-2, EXT-2S, EXT-3, EXT-4, EXT-4S, PC, DIGITAL TV) 5& 9 Colour button MENU = Menu button = Cursor Up button OK button $9 = Cursor Right button BACK = Back button = Volume - /+ buttons GUIDE button TV/RADIO = No Function 0(18 79 '79 PC Control buttons = Hyper Sound On/Off button ZOOM = Zoom button 2.
Features It is a remote controlled Integrated Digital colour television and PC monitor. 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system. It has 2 pieces of Euroconnector socket for external devices (such as video, video games, audio set, etc.) S-Video and AV inputs are available. Optional stereo sound systems (German or German+Nicam) are available. Multilanguage OSD.
Getting Started Follow Step 1 to 7 to set up your TV: Step 1: Checking the accessories supplied Remote control unit x 1 AA/R6 battery x 2 AC adapter x 1 Power cord x 1 Step 2: Inserting batteries Remove the battery cover located on the back of the remote control by gently pulling upwards from the indicated part. Insert two AA/R6 dry cell or equivalent type of batteries inside. Replace the battery cover.
FDUG VRFNHW 100 mm mount based on VESA regulation is equipped. The handle and the stand can be left by loosing the screws with a screwdriver when mounting the TV on a wall. Spread a soft cloth on a flat table and then place the TV on the cloth with the screen facing downwards when you leave the handle and the stand. Step 4: Connecting an aerial VCR and mains Please read the user manual of each device before connecting, to ensure a correct setup. It is necessary to connect aerial to watch TV.
&RQQHFW D YLGHR GHYLFH $(5,$/ (;7 (;7 $& DGDSWHU 7R '& ,1 9&5 IMPORTANT: Only use the adaptor supplied with this TV. The TV set is designed to operate on 12 V DC. For this, an adaptor is used which gives 12 V DC voltage. Connect this adaptor to a system that supplies 100-240 V AC, 50 Hz. Step 5: Using the cable holder A cable holder which is used to keep the connection cables tidy is supplied.
Step 6: Switching the TV ON/OFF To switch the TV on 35 /LVW (PSW\ 6WDUW DXWRPDWLF VHDUFK Your TV will switch on by two steps: 1- Connect the power supply cord to the system. Then the TV switches itself to standby mode and the power lamp becomes red located on the front of the TV. 2- To switch on the TV from stand-by mode either: Press the , button on the remote control or on the right side of the TV or.
To cancel APS before starting, press BLUE button. SMARTLINK (A trademark of Sony Corporation) First of all choose the Language which the menus of the analogue part of the TV will appear. As soon as you change the language, the menu items will be displayed in the selected language. By pressing the or button, come to the Country item and select the country. This will affect the sort process in APS. Press RED button to start A.P.S.
number buttons) during recording, a message appears asking if you want to stop recording or not. Press OK button to stop recording or BLUE button to continue recording. Do not turn the TV off in the following cases: When recording images from an external device connected to TV (For example camcorder). When recording a TV channel after it has been unscrambled on a decoder. When recording a TV channel by using the TVs output because the VCRs own tuner can not properly receive that channel.
dication of the strength of the signal received on this tuning channel. Operating while watching IDTV Pressing the TV/DTV button at any time while watching television programmes will switch the TV set between displaying the digital terrestrial television broadcasting and its normal analogue broadcasting. It is also used to switch to the last watched mode (TV or DIGITAL TV) from the EXT mode.
You can not set the reminder for the programme which has already started. M Current date and time N Channel listings O Selected date and time P Programme name and broadcast time Q Brief description of the programme No Information is displayed for the programme or channel which does not have any information. You can not set the reminder for these programmes. The programme name, broadcast time and a brief description of the programme are displayed for the programme chosen from the channel listings.
With Digital terrestrial broadcasting (DVB-T), in addition to digital teletext broadcasting at the same time as normal broadcasting, there are also channels with just digital teletext broadcasting. The aspect ratio when watching a channel with just digital teletext broadcasting is the same as the aspect ratio of the picture watched previously. DTV Menus The DTV menu can only be shown when watching Digital terrestrial broadcasting. To display the DTV menu, do the following: 1. Press MENU button.
Provided that the days and times are not the same, you can set up to ten timer settings. 3. Use the / buttons, number buttons and OK button to set the timer. When subtitles are ON, the subtitles displayed with the broadcast will be recorded. When you do not want to record the subtitles, you need to turn OFF the subtitles settings beforehand ( See Displaying the subtitles on Page18). When setting the start time and end time, input 1200 for 12:00 PM, 1500 for 3:00 PM and 0000 for 12:00 AM.
When recording on a T-V LINK incompatible VCR: will be superimposed over the picture in the VCR recording. 1. Insert the videotape for recording into the VCR and set the recording mode. When you press the following buttons ( 2. Set the VCR recording timer settings. 3. Make sure that the start and end time match with the TV timer. 4. Set the VCR to record the signal from the external input that the TV is connected to. Cancelling the timer setting For details, see your VCR instruction manual.
MENU When the Configuration menu is entered, MENU is highlighted. Use left or right buttons to change language between English or Spanish. MENU Language determines the on-screen menu language. Audio Language With Digital terrestrial broadcasting (DVB-T), a number of languages can be broadcast at the same time. Choose language you want to listen when watching these broadcasts. 1. Press the / Audio Language. By pressing / button, select Dolby Digital. Dolby Digital can be set to On or Off.
If it is correct, the Parental Settings Menu including following items is displayed: Your newly chosen PIN code is now set. You will now need to use the PIN code (password) you choose. Here to lock or to unlock the Edit PR Lists Lock. $JH 0DWXULW\ /RFN 0HQX /RFN ,QVWDOODWLRQ Edit PR List (QWHU 3,1 FRGH Choose Edit PR List and press the OK button. Use or buttons to highlight the menu item that will be adjusted. EDIT PR LIST appears.
Choosing a channel The chosen channel is shown on the quarterscreen. 2. Press the / buttons and choose the channel to be locked, and then press the OK button. The Enter PIN code input window appears. 1. Press the / buttons and choose Select on the bar at the bottom of the screen. 2. Press the / buttons and choose a channel, and then press the OK button. The picture of the chosen channel is shown on the quarter-screen. 3. Press the number buttons to input to correct PIN code.
Installation Although your TV will not lose its settings or stored channels when switched off, you may wish to re-install the programs because you have moved to a different area with different broadcast frequencies, you wish to reinstate a channel previously deleted from the channel list, or you want to watch new channels which have started broadcasting. Display the DTV Menu and using the or buttons, highlight the Installation line and press OK to display the Installation Menu.
Hint The bar graphs of signal quality and signal level give a good indication of whether any channels are likely to be found. If only the signal level graph shows a high value then it is likely that an analogue channel occupies that broadcast frequency. If the signal quality bar is high as well then it is a digital frequency and digital channels will probably be found. Again, channels which duplicate those already in the channel list are ignored.
ton, and press or button or directly press OK button. Press button to decrease contrast level. In EXT-1, EXT-2 and EXT-4 modes, main menu appears the same as in TV mode but without Program sub-menu. In EXT-3 mode, Main Menu appears as follows: 0HQX 3LFWXUH 6RXQG Setting Bright-1 )HDWXUH ,QVWDOO 6RXUFH + .K] 9 +] In DIGITAL TV mode, DIGITAL will appear on the Main menu. Install and Program do not appear.
pear in AV mode only when NTSC video source is applied. Otherwise, HUE option is invisible in Picture menu in TV mode : Using or button select Hue. Press button to increase hue level. Press button to decrease hue level. Center value is indicated with one arrow. Reset Setting Bright-2 Press BLUE button to reset the picture modes to factory default settings. Using or button select Bright-2. Press button to increase the back light.
Press button to increase treble level. Press button to decrease treble level Selecting Sound Mode Using Mode. Setting Balance It allows adjusting the distribution between the left and right speakers. Using or button select Balance. Press ward. button to change balance right- Press ward. button to change balance left- Hyper Sound Using Sound. or button select Hyper Press Mode.
The Child Lock feature can be set On or Off by In EXT mode, Install menu appears like this: / button. When Off is selected, there will be no difference in the operation of your TV. When On is selected, the TV can only be controlled by the remote control. In this case You can change only Colour system and VCR. the control panel buttons except button on the right side of the TV will not work. Selecting Menu Language Using or Press or guage. button select Language.
Decoder (EXT-2) You can use this mode to connect any decoder to your TV. Press the or buttons to set it On or Off. When you select Decoder (EXT-2) On, EXT-2 output will be chosen as TV mode only and any scrambled channels will be unscrambled through decoder connected your TV via EXT-2 output. Setting VCR ( Video Cassette Recorder ) Mode This item can be seen in TV, EXT-1, EXT-2, EXT-2S, EXT-3, EXT-4 and EXT-4S modes.
choose each character of channel name. 4. Press the RED button to store the channel name. To cancel the Name mode, press the BLUE button. To delete a channel (Delete): 1. Choose the channel you want to delete. 2. Press the YELLOW button to enter the Delete mode. 3. Press the YELLOW button to delete it. To cancel the Delete mode, press the BLUE button.
EXT Modes 'XDO ,, If Dual II selected by Remote Control. Hyper Sound By selecting Hyper Sound in sound menu or button on your remote by pressing the control, Pseudo/Spatial effect can be turned on or off. In Mono transmission the left and right channels will be added at left channel and dummy stereo effect will introduced to end-user. In stereo transmission it yields a phase difference between left and right channels.
Auto Position PC Mode Installation Power off both Computer and the TV before making any connections. Set your PCs resolution correctly before connecting to the TV. See the table in page 42 for supported modes. Use a D-SUB cable to connect the TVs PC input to the computers RGB output terminal. If you want to listen to the sound from the computer, use an audio cable to connect the PC AUDIO IN to the computers sound output terminal.
PC Picture Menu Setting PIP Size In the Main menu, select PC Picture using or button, then enter the PC Picture Using or button select PIP Size. Press or button to change PIP size. menu by pressing / or OK buttons. Two different PIP sizes are available. Contrast, Bright-1 and Colour Temperature adjustments in this menu are identical to adjustments defined in TV picture menu. Setting PIP Position R, G, and B adjust the TV image colour in PC mode.
No-Signal and Out Of Range Detection (PC mode) In PC Mode,as no menu is displayed,in case that there is no PC input to the TV, it is displayed an OSD message: No input signal detected The selected page number is displayed at the top left corner of the screen. The Teletext page counter searches until the selected page number is located, so that the desired page is displayed on the screen. Press button to move the Teletext screen forward one page at a time.
To Stop Automatic Page Change The teletext page you have selected may contain more information than what is on the screen; the rest of the information will be displayed after a period of time. Press button to stop the automatic page change. Press button again to allow the next page to be displayed. To Select a Subcode Page Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time.
Peripheral Equipment Connections There is a wide range of audio and video equipment that can be connected to your TV. Connection diagrams at the end of this section show you where the different equipment should be connected at the back side of the TV. Via the Euroconnector Your TV set has 2 Euroconnector sockets. If you want to connect peripherals (e.g. video, decoder, etc.) which have Euroconnectors, to your TV, use EXT-1 or EXT-2 input.
NTSC Playback Connect a NTSC video recorder to a terminal. Then press AV button to select the corresponding AV mode. NTSC 3.58/4.43 system is detected automatically in AV mode. Camera and Camcorder To connect to the EXT-4 terminal Connect your camera or camcorder at the back side of your TV. Connect your equipment to the TV via VIDEO (yellow), AUDIO R (red) and AUDIO L (white) inputs. You should connect the jacks to the input in the same colour.
Peripheral Equipment Connections 9 $ '& ,1 % 3& ,1387 & (;7 ' (;7 ( (;7 9 9 9 9 ) $17(11$ * 3& $8',2 ,1 + (;7 , +($'3+21( - $8',2 287 7(50,1$/ . &$5' 6/27 < 3E 3U &RPSRQHQW $XGLR ,Q 5 &RPSRQHQW $XGLR ,Q / 6 9LGHR ,Q 9LGHR ,Q $XGLR 5 $XGLR / $XGLR 5 $XGLR / 'LJLWDO $XGLR 2XW - 40 01-ENG-20710-17MB16P-C1897S UK-(LT-20DJ5SSP)-(TVAVOK)-IDTV-10041702-50087315.p65 40 07.06.
Antenna Connections 2XWGRRU $QWHQQD &RQQHFWLRQV 9+) DQWHQQD 5RXQG RKP FRD[LDO FDEOH 5HDU RI 79 )ODW RKP WZLQ OHDG FDEOH 9+) 8+) DQWHQQD 5HDU RI 79 5RXQG RKP FRD[LDO FDEOH Peripheral Equipment Connections HEADPHONE AUDIO $8',2 ,1 / 9,'(2 ,1 5 VIDEO ,1 287 ,1 $17 ,1 &$0&25'(5 FOR SATELLITE RECEIVER DECODER - 41 01-ENG-20710-17MB16P-C1897S UK-(LT-20DJ5SSP)-(TVAVOK)-IDTV-10041702-50087315.p65 41 07.06.
PC Input Typical Display Modes The display has a maximum resolution of 800 x 600, vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-47 KHz. The following table is an illustration of some of the typical video display modes.
PC Picture Tips Can not turn the TV on? Check that TV/VCR/DVD switch is set to TV position. If no PC picture appears, check that the DSUB cable is connected properly. Check that your PCs resolution set correctly. See pages 42 for supported modes. TV may go to stand-by mode when you turn the TV on soon after you turn the TV off. If you can turn the TV on again, it is not a problem.
Specifications Item Model LT-20DJ5SSP Broadcasting Systems PAL SECAM BG, DK, I, L, Lp Channels and Digital : 474 MHz - 858 MHz Frequencies Analogue : 46.25 MHz - 862.25 MHz Cable TV Input Signal (S1-S20/ S21-S41) Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync. Horizontal Timing 30 - 69 kHz Vertical Timing 50 - 75 khz Dot Rate 78,75 MHz max.