ENGLISH KD-R326/KD-R325 CD RECEIVER / Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, TH © 2010 Victor Company of Japan, Limited CoverRear_KD-R326_R325[U]_1.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
How to attach/detach the control panel CONTENTS 3 How to attach/detach the control panel 3 How to reset your unit 3 How to forcibly eject a disc 3 Maintenance 4 How to reset your unit Your preset adjustments will also be erased. How to forcibly eject a disc 4 5 5 6 7 8 9 [Hold] • Be careful not to drop the disc when it ejects. • If this does not work, reset your unit. Maintenance Cleaning the unit Wipe off the dirt on the panel with a dry silicon or soft cloth.
Canceling the display demonstration Display demonstration will be activated automatically if no operation is done for about 20 seconds. 1 Turn on the power. 4 Select . 2 5 [Hold] (Initial setting) 3 6 Finish the procedure. (Initial setting) Setting the clock 1 Turn on the power. 2 [Hold] (Initial setting) 3 Select . 4 Select . 5 Adjust the hour. (Initial setting) 6 Adjust the minute. 7 Finish the procedure. 4 ENGLISH EN02-15_KD-R326_R325[U]_4.
Preparing the remote controller When you use the remote controller for the first time, pull out the insulation sheet. Insulation sheet If the effectiveness of the remote controller decreases, replace the battery. Replacing the lithium coin battery CR2025 Caution: • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
Basic operations Loading slot Control dial Remote sensor • DO NOT expose to bright sunlight. Display window Ejects the disc Front auxiliary input jack Detaches the panel When you press or hold the following button(s)... Main unit Remote controller General operation • Turns on. • Turns off [Hold]. Selects the sources (FM, CD, F-AUX, BT AUDIO or R-AUX or SOURCE BT PHONE, AM). • “CD” is selectable only when a disc is loaded. VOL – / + • Adjusts the volume level. • Selects items.
Listening to the radio • Auto search [Press]. • Manual search [Hold]. “M” flashes, then press the button ] “FM” or “AM” repeatedly. “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. ~ Ÿ Improving the FM reception 1 [Hold] Manual presetting (FM/AM) You can preset up to 18 stations for FM and 6 stations for AM. 1 2 ] ] ] Reception improves, but stereo effect will be lost.
Listening to a disc ~ Ÿ Playback starts automatically. ] “CD” All tracks will be played repeatedly until you change the source or eject the disc. Stopping playback and ejecting the disc If the ejected disc is not removed within 15 seconds, it is automatically inserted into the loading slot.
Connecting the other external components You can connect an external component to the auxiliary input jack on the control panel (F-AUX) and/or on the rear side of the unit (R-AUX). Summary of using the external components through the auxiliary input jacks: External component Portable audio player Bluetooth device Preparation Connecting Auxiliary Source cable/device Menu setting Subinput jack name Setting (not supplied) item item Front SRC SELECT F-AUX ON F-AUX See below.
Selecting a preset sound mode You can select a preset sound mode suitable for the music genre. FLAT = NATURAL = DYNAMIC = VOCAL BOOST = BASS BOOST = USER = (back to the beginning) While listening, you can adjust the tone level of the selected sound mode. 1 2 ] ] 3 Adjust the sound elements of the selected tone. [Hold] 2 Adjust the level (–06 to +06) of the selected tone (BASS/ MID/ TRE). The sound mode is automatically stored and changed to “USER.
DISPLAY DIMMER Menu item AUTO : Dims the display to the previous setting when you turn on the car headlights. *1 / ON : Dims the display and button illumination (50% of the selected brightness level). / OFF : Cancels (100% of the selected brightness level). BRIGHTNESS DAY [ 31 ] / NIGHT [ 15 ] : Selects the display and button illumination brightness level [00 — 31] for day and night. SCROLL *2 ONCE : Scrolls the displayed information once. / AUTO : Repeats scrolling (at 5-second intervals).
Menu item SSM *8 See page 7. TUNER MONO *8 See page 7. IF BAND AUTO : Increases the tuner selectivity to reduce interference noises between adjacent stations. (Stereo effect may be lost.) / WIDE : Subject to interference noises from adjacent stations, but sound quality will not be degraded and the stereo effect will remain. AM *9 ON / OFF : Enable or disable “AM” in source selection. F-AUX *9 ON / OFF : Enable or disable “F-AUX” in source selection.
Disc playback FM/AM General Troubleshooting Symptom Remedy/Cause Sound cannot be heard from the speakers. • Adjust the volume to the optimum level. • Make sure the unit is not muted/paused. (page 6) • Check the cords and connections. Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. (page 3) If the message does not disappear, consult your JVC car audio dealer or a company supplying kits. Reset the unit.
Using Bluetooth ® devices For Bluetooth operations, it is required to connect the Bluetooth adapter, KS-BTA100 (not supplied) to the auxiliary input jack (R-AUX/BT ADAPTER) on the rear of the unit. (page 9) • For details, refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth device. Preparation 1 Register (pair) a Bluetooth device with KS-BTA100. Refer to the instructions manual supplied with KS-BTA100. 2 Change the settings of this unit.
Specifications AUDIO AMPLIFIER SECTION CD PLAYER SECTION Maximum Power Output : 50 W per channel Continuous Power Output (RMS) : 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Signal-to-Noise Ratio : 70 dB Load Impedance : 4 Ω (4 Ω to 8 Ω allowance) Frequency Response : 40 Hz to 20 000 Hz Line-Out or Subwoofer-Out Level/ Impedance : 2.
KD-R326/KD-R325 Installation/Connection Manual การติดตั้ง/คู่มือการติดตั้ง GET0675-006A 0910DTSMDTJEIN [U/UH] EN, TH © 2010 Victor Company of Japan, Limited ENGLISH / ไทย WARNINGS / คำเตือน • ต้องใช้ชุดติดตั้งที่เหมาะสมกับรถของท่าน • หากท่านมีคำถามหรือต้องการข้อมูลเกีย่ วกับชุดติดตั้ง • You need the installation kits which corresponds to your car. • If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
ELECTRICAL CONNECTIONS / การเชือ่ มต่อไฟฟ้ า Signal cord / สายสัญญาณ*1 JVC Amplifier / แอมพลิฟลายเออร์ของ JVC Rear speakers or subwoofer / ลำโพงหลังหรือซับวูฟเฟอร *3 Rear ground terminal / ขั้วต่อสายดินด้านหลัง Reset the unit. / ตั้งค่าเครือ่ งใหม่ 10 A fuse / ฟิ วส์ 10 A Remote lead / สายรี โมท Factory wiring harness (vehicle) / ชุดสายไฟจากโรงงาน (รถยนต์) Antenna terminal / ขัว้ ต่อสายอากาศ Extension lead / สายต่อขยาย *1 Caution / ข้อควรระวัง Join the same color leads together.
ENGLISH KD-R326/KD-R325 CD RECEIVER / Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, TH © 2010 Victor Company of Japan, Limited CoverRear_KD-R326_R325[U]_1.