IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT. KD-R514 CD RECEIVER : INSTRUCTIONS/INSTALLATION Thank you for purchasing a JVC product.
Listening to the radio ~ Ÿ ] “FM” or “AM” Listening to the disc ~ Ÿ ] Turn on the power. “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. Manual search “M” flashes, then press the button repeatedly. All tracks will be played repeatedly until you change the source or eject the disc. Selecting a preset station 1 Stopping playback and ejecting the disc Selecting the playback modes “NO DISC” appears. Press / SOURCE to listen to another playback source.
Selecting the variable buttons and display color illumination Menu operations 1 [Hold] DEMO DEMO CLOCK SET Selectable setting, [Initial: Underlined] • DEMO ON • DEMO OFF : Display demonstration will be activated automatically if no operation is done for about 20 seconds. : Cancels. [ 1:00 ] : Adjust the hour, then the minute. BASS — MIDDLE DIMMER • DIMMER ON • DIMMER OFF SCROLL *1 • SCROLL ONCE : Scrolls the displayed information once.
Electrical connections Installation IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended for connection between the unit and your car. • Consult your JVC car audio dealer or a company supplying kits for details. Prepare these before installation.... This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
Troubleshooting Symptom Basic operations Remedy/Cause Sound cannot be heard from the speakers. • Adjust the volume to the optimum level. • Make sure the unit is not muted/paused. (See page 1.) • Check the cords and connections. “PROTECT” appears on the display and no operations can be done. Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. (See page 1.
Maintenance Specifications How to clean the connectors To play new discs Wipe the connectors with a cotton swab or cloth moistened with alcohol. Remove any rough areas from the inner and outer edges of the disc. AUDIO AMPLIFIER SECTION Maximum Power Output: Front/Rear: 50 W per channel Continuous Power Output (RMS): Front/Rear: 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion.
ENGLISH KD-R516 / KD-R515 Having TROUBLE with operation? CD RECEIVER / Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, TH © 2009 Victor Company of Japan, Limited CoverRear_KD-R516_001A_1.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
How to attach/detach the control panel CONTENTS 2 How to read this manual 3 How to attach/detach the control panel 4 How to reset your unit Your preset adjustments will also be erased. How to forcibly eject a disc [Hold] • You can forcibly eject the loaded disc even if the disc is locked. To lock/unlock the disc, 9. • Be careful not to drop the disc when it ejects. • If this does not work, reset your unit.
Canceling the display demonstration 1 Turn on the power. 4 Select . 2 5 [Hold] (Initial setting) 3 6 Finish the procedure. Setting the clock 1 Turn on the power. 2 [Hold] (Initial setting) 3 Select . 4 Select . 5 Adjust the hour. 6 Adjust the minute. 7 Finish the procedure. 4 ENGLISH EN02-09_KD-R516_001A_1.
Preparing the remote controller (RM-RK50) When you use the remote controller for the first time, pull out the insulation sheet. Insulation sheet If the effectiveness of the remote controller decreases, replace the battery. Replacing the lithium coin battery CR2025 Caution: • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
Basic operations Ejects the disc Loading slot Display window USB (Universal Serial Bus) input jack Control dial Auxiliary input jack Detaches the panel Remote sensor • DO NOT expose to bright sunlight. When you press or hold the following button(s)... Main unit Remote controller General operation Turns on. • When the power is on, pressing /I/ATT on the remote controller also mutes the sound or pauses. Press /I/ATT again to cancel muting or resume playback. Turns off if pressed and held.
Main unit Remote controller General operation — • Enters setting directly ( 16). • Enters setting directly ( 17) if pressed and held. — Returns to the previous menu. — Power off : Checks the current clock time. Power on : Changes the display information. Listening to the radio ~ Ÿ ] “FM” or “AM” “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. Manual search Automatic presetting (FM)— “M” flashes, then press the button repeatedly.
Manual presetting (FM/AM) Title assignment You can preset up to 18 stations for FM and 6 stations for AM. You can assign titles up to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title. • If you try to assign titles to more than 30 station frequencies, “NAME FULL” appears. Delete unwanted titles before assignment. Ex.: Storing FM station of 92.50 MHz into preset number “04.” 1 ] “92.50MHz” 2 [Hold] 1 ] “FM” or “AM” 2 “PRESET MODE” flashes.
Listening to a disc ~ Ÿ ] Turn on the power. All tracks will be played repeatedly until you change the source or eject the disc. Caution on volume setting: Selecting a track/folder Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level. Stopping playback and ejecting the disc “NO DISC” appears. Press / SOURCE to listen to another playback source.
Using the remote controller Changing the display information 5 U / D ∞ : Selects folder of the MP3/WMA 2 R / F 3 : Selects track 2 R / F 3 : Fast-forwards or [Hold] reverses the track Disc title/Album name/performer (folder name)* = Track title (file name)* = Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning) * If the current disc is an audio CD, “NO NAME” appears.
Cautions: • Avoid using the USB device if it might hinder your safety driving. • Do not pull out and attach the USB device repeatedly while “READING” is shown on the display. • Do not start the car engine if a USB device is connected. • This unit may not be able to play the files depending on the type of USB device. • Operation and power supply may not work as intended for some USB devices. • You cannot connect a computer to the USB input terminal of the unit.
Selecting a preset sound mode You can select a preset sound mode suitable for the music genre. FLAT = NATURAL = DYNAMIC = VOCAL BOOST = BASS BOOST = USER = (back to the beginning) Storing your own sound mode You can store your own adjustments in memory. 1 2 While listening, you can adjust the tone level of the selected sound mode. 1 [Hold] [Hold] ] ] / / 3 2 Adjust the level (–06 to +06) of the selected tone (BASS / MID / TRE).
Menu operations 1 [Hold] DEMO Category 2 3 Menu item DEMO Display demonstration Selectable setting, [Initial: Underlined] • DEMO ON : Display demonstration will be activated automatically if no operation is done for about 20 seconds. : Cancels. ( 4) CLOCK SET Clock setting — [1:00] : Adjust the hour, then the minute. ( BASS — : For settings, 4) 12. MIDDLE TREBLE DIMMER • DIMMER ON : Dims the display and button illumination. • DIMMER OFF : Cancels.
TUNER Category Menu item IF BAND Intermediate frequency band • WIDE BUTTON ZONE COLOR Selectable setting, [Initial: Underlined] • AUTO DISP ZONE Display zone : Increases the tuner selectivity to reduce interference noises between adjacent stations. (Stereo effect may be lost.) : Subject to interference noises from adjacent stations, but sound quality will not be degraded and the stereo effect will remain. COLOR 01 — : For settings, COLOR 29, USER 16. • BUTTON ZONE : For settings, • DISP ZONE 17.
Category Menu item L/O MODE Line output mode Selectable setting, [Initial: Underlined] • SUB.W • REAR SRC SELECT AUDIO SUB.W FREQ *5 • LOW Subwoofer cutoff frequency • MID • HIGH : Select if the REAR LINE OUT terminals are used for connecting a subwoofer (through an external amplifier). : Select if the REAR LINE OUT terminals are used for connecting the speakers (through an external amplifier). : Frequencies lower than 72 Hz are sent to the subwoofer.
Selecting the variable buttons and display color illumination You can select your preferred color for buttons illumination (except for EQ/BASS-TRE / DISP) and display color separately. Button zone Display zone All zone 1 [Hold] or 4 2 ] ]
Creating your own day and night colors—USER You can create your own colors for and to apply to button zone and display zone. • Displayed when is set to . • Displayed when is set to . Menu hierarchy DAY COLOR COLOR SETUP NIGHT COLOR • BUTTON ZONE • DISP ZONE • BUTTON ZONE Operation Follow example below. Press BACK after step 5, then select DISP ZONE in step 2.
Maintenance How to clean the connectors To keep discs clean Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors. A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. • Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.
More about this unit Basic operations General • If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power. • If no operation is done for about 60 seconds after pressing MENU button, the operation will be canceled. Tuner operations Storing stations in memory • During SSM search... – All previously stored stations are erased and the stations are stored anew.
• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck to the surface. – Discs on which labels can be directly printed by an ink jet printer. Using these discs under high temperature or high humidity may cause malfunctions or damage to the unit. Playing an MP3/WMA disc • This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).
• The maximum number of characters for: – Folder names : 32 characters – File names : 32 characters – MP3 Tag : 64 characters – WMA Tag : 32 characters • This unit can recognize a total of 5 000 files, 255 folders (255 files per folder including folder without unsupported files), and of 8 hierarchies. • This unit does not support SD card reader. • This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 500 mA.
MP3/WMA playback Disc playback Symptom 22 Remedy/Cause Disc cannot be played back. Insert the disc correctly. • CD-R/CD-RW cannot be played back. • Tracks on the CD-R/CD-RW cannot be skipped. • Insert a finalized CD-R/CD-RW. • Finalize the CD-R/CD-RW with the component which you used for recording. Disc can neither be played back nor ejected. 9) • Unlock the disc. ( • Eject the disc forcibly. ( Disc sound is sometimes interrupted. • Stop playback while driving on rough roads. • Change the disc.
USB device playback Symptom Remedy/Cause Noise is generated. The track played back is not an MP3/WMA track. Skip to another file. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.) “READING” keeps flashing on the display. • Readout time varies depending on the USB device. • Do not use too many hierarchy or folders. • Turn off the power then on again. • Reattach the USB device again. “NO FILE” appears on the display. Selected folder is an empty folder *.
Specifications Maximum Power Output: TUNER SECTION AUDIO AMPLIFIER SECTION Continuous Power Output (RMS): 24 Front/ Rear: Front/ Rear: 50 W per channel 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±12 dB (60 Hz, 80 Hz, 100 Hz, 200 Hz) Q1.0, Q1.25, Q1.5, Q2.0 Middle: ±12 dB (0.5 kHz, 1.0 kHz, 1.5 kHz, 2.5 kHz) Q0.75, Q1.0, Q1.25 Treble: ±12 dB (10.0 kHz, 12.5 kHz, 15.0 kHz, 17.
GENERAL USB SECTION CD PLAYER SECTION Type: Signal Detection System: Compact disc player Non-contact optical pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 320 kbps USB Standard: USB 1.1, USB 2.
ENGLISH KD-R516 / KD-R515 Having TROUBLE with operation? CD RECEIVER / Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, TH © 2009 Victor Company of Japan, Limited CoverRear_KD-R516_001A_1.
KD-R516/KD-R515 Installation/Connection Manual การติดตั้ง/คู่มือการติดตั้ง GET0634-006A 1209DTSMDTJEIN [U/UH] EN, TH © 2009 Victor Company of Japan, Limited ENGLISH / ไทย You need the installation kits which corresponds to your car.
ELECTRICAL CONNECTIONS / การเชือ่ มต่อไฟฟ้ า ข้อสำคัญ: ขอแนะนำให้ ใช้ชุดสายไฟแบบสั่งทำ (แยกซื้อต่างหาก) ซึ่งเหมาะสำหรับรถของคุณ เพื่อใช้เชื่อมต่อระหว่างเครือ่ งและรถ • สอบถามตัวแทนจำหน่ายวิทยุ JVC ของคุณหรือบริษัทที่จัดส่งชุดอุปกรณ์เพื่อขอรายละเอียด IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommanded for connection between the unit and your car. • Consult your JVC car audio dealer or a company supplying kits for details.
ENGLISH KD-R516 / KD-R515 Having TROUBLE with operation? CD RECEIVER / Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, CT © 2009 Victor Company of Japan, Limited CoverRear_KD-R516_005A_f.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
How to attach/detach the control panel CONTENTS 2 How to read this manual 3 How to attach/detach the control panel 4 How to reset your unit Your preset adjustments will also be erased. How to forcibly eject a disc [Hold] • You can forcibly eject the loaded disc even if the disc is locked. To lock/unlock the disc, 9. • Be careful not to drop the disc when it ejects. • If this does not work, reset your unit.
Canceling the display demonstration 1 Turn on the power. 4 Select . 2 5 [Hold] (Initial setting) 3 6 Finish the procedure. Setting the clock 1 Turn on the power. 2 [Hold] (Initial setting) 3 Select . 4 Select . 5 Adjust the hour. 6 Adjust the minute. 7 Finish the procedure. 4 ENGLISH EN02-09_KD-R516_001A_1.
Preparing the remote controller (RM-RK50) When you use the remote controller for the first time, pull out the insulation sheet. Insulation sheet If the effectiveness of the remote controller decreases, replace the battery. Replacing the lithium coin battery CR2025 Caution: • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
Basic operations Ejects the disc Loading slot Display window USB (Universal Serial Bus) input jack Control dial Auxiliary input jack Detaches the panel Remote sensor • DO NOT expose to bright sunlight. When you press or hold the following button(s)... Main unit Remote controller General operation Turns on. • When the power is on, pressing /I/ATT on the remote controller also mutes the sound or pauses. Press /I/ATT again to cancel muting or resume playback. Turns off if pressed and held.
Main unit Remote controller General operation — • Enters setting directly ( 16). • Enters setting directly ( 17) if pressed and held. — Returns to the previous menu. — Power off : Checks the current clock time. Power on : Changes the display information. Listening to the radio ~ Ÿ ] “FM” or “AM” “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. Manual search Automatic presetting (FM)— “M” flashes, then press the button repeatedly.
Manual presetting (FM/AM) Title assignment You can preset up to 18 stations for FM and 6 stations for AM. You can assign titles up to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title. • If you try to assign titles to more than 30 station frequencies, “NAME FULL” appears. Delete unwanted titles before assignment. Ex.: Storing FM station of 92.50 MHz into preset number “04.” 1 ] “92.50MHz” 2 [Hold] 1 ] “FM” or “AM” 2 “PRESET MODE” flashes.
Listening to a disc ~ Ÿ ] Turn on the power. All tracks will be played repeatedly until you change the source or eject the disc. Caution on volume setting: Selecting a track/folder Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level. Stopping playback and ejecting the disc “NO DISC” appears. Press / SOURCE to listen to another playback source.
Using the remote controller Changing the display information 5 U / D ∞ : Selects folder of the MP3/WMA 2 R / F 3 : Selects track 2 R / F 3 : Fast-forwards or [Hold] reverses the track Disc title/Album name/performer (folder name)* = Track title (file name)* = Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning) * If the current disc is an audio CD, “NO NAME” appears.
Cautions: • Avoid using the USB device if it might hinder your safety driving. • Do not pull out and attach the USB device repeatedly while “READING” is shown on the display. • Do not start the car engine if a USB device is connected. • This unit may not be able to play the files depending on the type of USB device. • Operation and power supply may not work as intended for some USB devices. • You cannot connect a computer to the USB input terminal of the unit.
Selecting a preset sound mode You can select a preset sound mode suitable for the music genre. FLAT = NATURAL = DYNAMIC = VOCAL BOOST = BASS BOOST = USER = (back to the beginning) Storing your own sound mode You can store your own adjustments in memory. 1 2 While listening, you can adjust the tone level of the selected sound mode. 1 [Hold] [Hold] ] ] / / 3 2 Adjust the level (–06 to +06) of the selected tone (BASS / MID / TRE).
Menu operations 1 [Hold] DEMO Category 2 3 Menu item DEMO Display demonstration Selectable setting, [Initial: Underlined] • DEMO ON : Display demonstration will be activated automatically if no operation is done for about 20 seconds. : Cancels. ( 4) CLOCK SET Clock setting — [1:00] : Adjust the hour, then the minute. ( BASS — : For settings, 4) 12. MIDDLE TREBLE DIMMER • DIMMER ON : Dims the display and button illumination. • DIMMER OFF : Cancels.
TUNER Category Menu item IF BAND Intermediate frequency band • WIDE BUTTON ZONE COLOR Selectable setting, [Initial: Underlined] • AUTO DISP ZONE Display zone : Increases the tuner selectivity to reduce interference noises between adjacent stations. (Stereo effect may be lost.) : Subject to interference noises from adjacent stations, but sound quality will not be degraded and the stereo effect will remain. COLOR 01 — : For settings, COLOR 29, USER 16. • BUTTON ZONE : For settings, • DISP ZONE 17.
Category Menu item L/O MODE Line output mode Selectable setting, [Initial: Underlined] • SUB.W • REAR SRC SELECT AUDIO SUB.W FREQ *5 • LOW Subwoofer cutoff frequency • MID • HIGH : Select if the REAR LINE OUT terminals are used for connecting a subwoofer (through an external amplifier). : Select if the REAR LINE OUT terminals are used for connecting the speakers (through an external amplifier). : Frequencies lower than 72 Hz are sent to the subwoofer.
Selecting the variable buttons and display color illumination You can select your preferred color for buttons illumination (except for EQ/BASS-TRE / DISP) and display color separately. Button zone Display zone All zone 1 [Hold] or 4 2 ] ]
Creating your own day and night colors—USER You can create your own colors for and to apply to button zone and display zone. • Displayed when is set to . • Displayed when is set to . Menu hierarchy DAY COLOR COLOR SETUP NIGHT COLOR • BUTTON ZONE • DISP ZONE • BUTTON ZONE Operation Follow example below. Press BACK after step 5, then select DISP ZONE in step 2.
Maintenance How to clean the connectors To keep discs clean Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors. A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. • Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.
More about this unit Basic operations General • If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power. • If no operation is done for about 60 seconds after pressing MENU button, the operation will be canceled. Tuner operations Storing stations in memory • During SSM search... – All previously stored stations are erased and the stations are stored anew.
• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck to the surface. – Discs on which labels can be directly printed by an ink jet printer. Using these discs under high temperature or high humidity may cause malfunctions or damage to the unit. Playing an MP3/WMA disc • This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).
• The maximum number of characters for: – Folder names : 32 characters – File names : 32 characters – MP3 Tag : 64 characters – WMA Tag : 32 characters • This unit can recognize a total of 5 000 files, 255 folders (255 files per folder including folder without unsupported files), and of 8 hierarchies. • This unit does not support SD card reader. • This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 500 mA.
MP3/WMA playback Disc playback Symptom 22 Remedy/Cause Disc cannot be played back. Insert the disc correctly. • CD-R/CD-RW cannot be played back. • Tracks on the CD-R/CD-RW cannot be skipped. • Insert a finalized CD-R/CD-RW. • Finalize the CD-R/CD-RW with the component which you used for recording. Disc can neither be played back nor ejected. 9) • Unlock the disc. ( • Eject the disc forcibly. ( Disc sound is sometimes interrupted. • Stop playback while driving on rough roads. • Change the disc.
USB device playback Symptom Remedy/Cause Noise is generated. The track played back is not an MP3/WMA track. Skip to another file. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.) “READING” keeps flashing on the display. • Readout time varies depending on the USB device. • Do not use too many hierarchy or folders. • Turn off the power then on again. • Reattach the USB device again. “NO FILE” appears on the display. Selected folder is an empty folder *.
Specifications Maximum Power Output: TUNER SECTION AUDIO AMPLIFIER SECTION Continuous Power Output (RMS): 24 Front/ Rear: Front/ Rear: 50 W per channel 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±12 dB (60 Hz, 80 Hz, 100 Hz, 200 Hz) Q1.0, Q1.25, Q1.5, Q2.0 Middle: ±12 dB (0.5 kHz, 1.0 kHz, 1.5 kHz, 2.5 kHz) Q0.75, Q1.0, Q1.25 Treble: ±12 dB (10.0 kHz, 12.5 kHz, 15.0 kHz, 17.
GENERAL USB SECTION CD PLAYER SECTION Type: Signal Detection System: Compact disc player Non-contact optical pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 320 kbps USB Standard: USB 1.1, USB 2.
ENGLISH KD-R516 / KD-R515 Having TROUBLE with operation? CD RECEIVER / Please reset your unit Refer to page of How to reset your unit For canceling the display demonstration, see page 4. / For installation and connections, refer to the separate manual. INSTRUCTIONS EN, CT © 2009 Victor Company of Japan, Limited CoverRear_KD-R516_005A_f.
KD-R516/KD-R515 Installation/Connection Manual 安裝/連接手冊 GET0634-010A 1209DTSMDTJEIN [UT] EN, CT © 2009 Victor Company of Japan, Limited ENGLISH / 中文 You need the installation kits which corresponds to your car. / Check the battery system in your car / To the car system / 您需要與您的汽車相配套的安裝元件。 查看汽車的電池系統 接至汽車系統 12 V DC, NEGATIVE ground / 直流 12 V,負極接地 WARNINGS / 警告 • To prevent short circuits: – Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
ELECTRICAL CONNECTIONS / 電路連接 重要事項: 建議將適用於您汽車的定製配線束(另購)連接在本機和汽車之間。 IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommanded for connection between the unit and your car. • Consult your JVC car audio dealer or a company supplying kits for details.
Having TROUBLE with operation? ENGLISH Please reset your unit FRANÇAIS Refer to page of How to reset your unit Vous avez des PROBLÈMES de fonctionnement? Réinitialisez votre appareil Référez-vous à la page intitulée Comment réinitialiser votre appareil KD-R511 CD RECEIVER / RÉCEPTEUR CD Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
How to read this manual The following icons/symbols are used to indicate: CONTENTS 3 How to read this manual 3 How to attach/detach the control Press and hold the button(s) panel [Hold] until the desired operation 3 How to reset your unit 3 How to forcibly eject a disc begins. Turn the control dial. Turn the control dial to make a selection, then press to confirm.
Canceling the display demonstration 1 Turn on the power. 4 Select . 2 5 [Hold] (Initial setting) 3 6 Finish the procedure. Setting the clock 1 Turn on the power. 2 6 Adjust the minute. [Hold] (Initial setting) 3 Select . 4 Select . 7 Select <24H/12H>. 8 Select <24 HOUR> or <12 HOUR>. 5 Adjust the hour. 9 Finish the procedure. 4 ENGLISH EN02-11_KD-R511_003A_1.
Basic operations Ejects the disc Loading slot Display window USB (Universal Serial Bus) input jack Control dial Auxiliary input jack Remote sensor You can control this unit with an optionally 12). purchased remote control, RM-RK50 ( Detaches the panel When you press or hold the following button(s)... Button General operation • Turns on. • Selects the available sources (if the power is turned on). If the source is ready, playback also starts. • Turns off if pressed and held.
Listening to the radio ~ ] “FM” or “AM” Ÿ “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. Manual search Automatic presetting (FM)— “M” flashes, then press the button repeatedly. [Hold] While listening to a station... When an FM stereo broadcast is hard to receive 1 1 [Hold] 2 [Hold] 2 ] ] ] Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure to select .
Manual presetting (FM/AM) You can preset up to 18 stations for FM and 6 stations for AM. Ex.: Storing FM station of 92.50 MHz into preset number “04.” 1 ] “92.50MHz” 2 [Hold] The following features are available only for FM Radio Data System stations. Searching for your favourite FM Radio Data System programme—PTY Search You can tune in to a station broadcasting your favourite programme by searching for a PTY code. 1 “PRESET MODE” flashes. 3 [Hold] The last selected PTY code appears.
Standby receptions Tracing the same programme— TA Standby Reception Network-Tracking Reception When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM Radio Data System station of the same network, possibly broadcasting the same programme with stronger signals. TA Standby Reception allows the unit to switch temporarily to Traffic Announcement (TA) from any source other than AM.
Listening to a disc ~ Ÿ ] Turn on the power. All tracks will be played repeatedly until you change the source or eject the disc. Caution on volume setting: Selecting a track/folder Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level. Stopping playback and ejecting the disc “NO DISC” appears. Press / SOURCE to listen to another playback source.
Changing the display information Disc title/Album name/performer (folder name)* = Track title (file name)* = Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning) * If the current disc is an audio CD, “NO NAME” appears. 14), If an MP3/WMA file does not have Tag information or is set to ( folder name and file name appear. Listening to the USB device This unit can play MP3/WMA files stored in a USB device.
Cautions: • Avoid using the USB device if it might hinder your safety driving. • Do not pull out and attach the USB device repeatedly while “READING” is shown on the display. • Do not start the car engine if a USB device is connected. • This unit may not be able to play the files depending on the type of USB device. • Operation and power supply may not work as intended for some USB devices. • You cannot connect a computer to the USB input terminal of the unit.
Using the remote controller KD-R511 can be remotely controlled as instructed here (with an optionally purchased remote controller). We recommend that you use remote controller RM-RK50 with your unit. Installing the lithium coin battery (CR2025) Caution: • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
Selecting a preset sound mode You can select a preset sound mode suitable for the music genre. FLAT = NATURAL = DYNAMIC = VOCAL BOOST = BASS BOOST = USER = (back to the beginning) Storing your own sound mode You can store your own adjustments in memory. 1 2 While listening, you can adjust the tone level of the selected sound mode. 1 [Hold] ] ] / / 3 2 Adjust the level (–06 to +06) of the selected tone (BASS / MID / TRE).
Menu operations 1 [Hold] DEMO Category 2 3 Menu item DEMO Display demonstration Selectable setting, [Initial: Underlined] • DEMO ON CLOCK • DEMO OFF : Display demonstration will be activated automatically if no operation is done for about 20 seconds. : Cancels. ( 4) CLOCK SET Clock setting — [0:00] : Adjust the hour, then the minute.
Category Menu item TUNER SSM *3 Strong-station Sequential Memory AF-REG *4 Alternative frequency/ regionalization reception PTYSTANDBY *3, *4 TA VOLUME *4 Traffic announcement volume P-SEARCH *4 Programme search MONO *3 Monaural mode Selectable setting, [Initial: Underlined] • SSM 01 – 06 • SSM 07 – 12 • SSM 13 – 18 : For settings, • AF ON : When the currently received signals become weak, the unit switches to another station (the programme may differ from the one currently received).
Category Menu item COLOR BUTTON ZONE DISP ZONE Display zone Selectable setting, [Initial: Underlined] COLOR 01 — : For settings, COLOR 29, USER 18. • BUTTON ZONE : For settings, • DISP ZONE 19. ALL ZONE COLOR SETUP DAY COLOR NIGHT COLOR • OFF : Changes the display and buttons (except for EQ/BASS-TRE / DISP ) illumination during menu, list search and playback mode operations. : Cancels. FADER *6 R06 – F06 [00] : Adjust the front and rear speaker output balance.
Category Menu item Selectable setting, [Initial: Underlined] SUB.W FREQ *8 • LOW Subwoofer cutoff frequency • MID SRC SELECT AUDIO • HIGH : Frequencies lower than 72 Hz are sent to the subwoofer. : Frequencies lower than 111 Hz are sent to the subwoofer. : Frequencies lower than 157 Hz are sent to the subwoofer. SUB.W LEVEL *8 Subwoofer level SUB.W 00 — SUB.W 08 [SUB.W 04] : Adjust the subwoofer output level. BEEP Keytouch tone • BEEP ON • BEEP OFF : Activates the keypress tone.
Selecting the variable buttons and display color illumination You can select your preferred color for buttons illumination (except for EQ/BASS-TRE / DISP ) and display color separately. Button zone Display zone All zone 1 [Hold] or 4 2 ] ]
Creating your own day and night colors—USER You can create your own colors for and to apply to button zone and display zone. • Displayed when is set to . • Displayed when is set to . Menu hierarchy DAY COLOR COLOR SETUP NIGHT COLOR • BUTTON ZONE • DISP ZONE • BUTTON ZONE Operation Follow example below. Press T/P BACK after step 5, then select DISP ZONE in step 2.
Maintenance How to clean the connectors To keep discs clean Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors. A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. • Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.
More about this unit Basic operations Disc/USB operations General Caution for DualDisc playback • If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power. • If no operation is done for about 60 seconds after pressing MENU button, the operation will be canceled. • The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard.
• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following reasons: – Discs are dirty or scratched. – Moisture condensation has occurred on the lens inside the unit. – The pickup lens inside the unit is dirty. – The files on the CD-R/CD-RW are written using the “Packet Write” method. – There are improper recording conditions (missing data, etc.) or media conditions (stained, scratched, warped, etc.).
• Connect one USB mass storage class device to the unit at a time. Do not use a USB hub. • If the connected USB device does not have the correct files, “CANNOT PLAY” appears. • This unit can show Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files. • This unit can play back MP3/WMA files meeting the conditions below: – Bit rate of MP3/WMA: 32 kbps — 320 kbps – Sampling frequency of MP3: 32 kHz, 44.1 kHz, 48 kHz (for MPEG-1) 16 kHz, 22.
MP3/WMA playback Disc playback FM/AM General Symptom Remedy/Cause “AUX IN” cannot be selected. Check the = setting. ( 17) Nothing appear on the display. Check the color settings ( SSM automatic presetting does not work. Store stations manually. Static noise while listening to the radio. Connect the aerial firmly. 19). “AM” cannot be selected. Check the = setting. ( Disc cannot be played back. Insert the disc correctly.
USB device playback MP3/WMA playback Symptom Remedy/Cause The elapsed playing time is not This sometimes occurs during playback. This is caused correct. by how the tracks are recorded on the disc. “NO FILE” appears on the display. Selected folder is an empty folder *. Select another folder that contains MP3/WMA tracks. “NOT SUPPORT” appears on the Skip to the next track encoded in an appropriate format display and track skips. or to the next non-copy-protected WMA track.
Specifications Maximum Power Output: Front/Rear: 50 W per channel Continuous Power Output (RMS): Front/Rear: 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) AUDIO AMPLIFIER SECTION Tone Control Range: ±12 dB (60 Hz, 80 Hz, 100 Hz, 200 Hz) Q1.0, Q1.25, Q1.5, Q2.0 Middle: ±12 dB (0.5 kHz, 1.0 kHz, 1.5 kHz, 2.5 kHz) Q0.75, Q1.0, Q1.25 Treble: ±12 dB (10.0 kHz, 12.5 kHz, 15.0 kHz, 17.
CD PLAYER SECTION Type: Compact disc player Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps USB SECTION WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 320 kbps USB Standard: USB 1.1, USB 2.
Having TROUBLE with operation? ENGLISH Please reset your unit FRANÇAIS Refer to page of How to reset your unit Vous avez des PROBLÈMES de fonctionnement? Réinitialisez votre appareil Référez-vous à la page intitulée Comment réinitialiser votre appareil KD-R511 CD RECEIVER / RÉCEPTEUR CD Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
KD-R511 Installation/Connection Manual Manuel d’installation/raccordement GET0635-010A 1209DTSMDTJEIN [E/EU] EN, FR © 2009 Victor Company of Japan, Limited ENGLISH / FRANÇAIS You need the installation kits which corresponds to your car. / Vous avez besoin des kits d’installation correspondants à votre voiture.
ELECTRICAL CONNECTIONS / RACCORDEMENTS ELECTRIQUES Connecting the external amplifier or subwoofer / Connexion d’un amplificateur extérieur ou d’un caisson de grave Y-connector / Connecteur Y *1 Remote lead / Fil d’alimentation à distance JVC Amplifier / JVC Amplificateur Signal cord / Cordon de signal *1 Reset the unit. / Réinitialisez l’autoradio.