Owner's Manual

ENGLISH
33
Audio
Tone Action Band Frequency: 62.5 Hz/100 Hz/160 Hz/
250 Hz/400 Hz/ 630 Hz/1 kHz/1.6 kHz/
2.5 kHz/4 kHz/6.3 kHz/10 kHz/16 kHz
Level: –09 — +09 (–9 dB — +9 dB)
Q: 1.35/1.5/2.0
HPF Frequency: Through/30 Hz/40 Hz/50 Hz/
60 Hz/70 Hz/80 Hz/90 Hz/100 Hz/120 Hz/
150 Hz/180 Hz/220 Hz/250 Hz
Slope: –6 dB/Oct./–12 dB/Oct./
–18 dB/Oct./–24 dB/Oct.
Gain: –8 dB/–7 dB/–6 dB/–5 dB/–4 dB/
–3 dB/–2 dB/–1 dB/0 dB
LPF Frequency: 30 Hz/40 Hz/50 Hz/60 Hz/
70 Hz/80 Hz/90 Hz/100 Hz/120 Hz/
150 Hz/180 Hz/220 Hz/250 Hz/Through
Slope: –6 dB/Oct./–12 dB/Oct./
–18 dB/Oct./–24 dB/Oct.
Gain: –8 dB/–7 dB/–6 dB/–5 dB/–4 dB/
–3 dB/–2 dB/–1 dB/0 dB
Speaker Impedance 4Ω—8Ω
Preout Level/Load (CD/USB) 4000mV/10kΩ load
Preout Impedance ≤600Ω
General
Operating Voltage
(10.5V—16V allowable)
14.4V
Maximum Current Consumption 10A
Operating Temperature Range –10°C — +60°C
Installation Size (W×H×D) 182mm×53mm×158mm
(7-3/16"×2-1/8"×6-1/4")
Weight
1.1k
g (2.43lbs)
Subject to change without notice.
SPECIFICATIONS
Warning
• The unit can only be used with a 12V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black)
to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and
shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the
wires of speakers to the car chassis or Ground wire (black), or connect them in
parallel.
• Connect speakers with a maximum power of more than 50W. If the maximum power of the speakers
is lower than 50W, change the
[AMP GAIN] setting to avoid damaging the speakers. (  22)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the
terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by
the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working
properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse
with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then disconnect the terminal of the car battery.
2 Connect the wires properly.
See Wiring connection.
(  35)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
(  34)
4 Connect the terminal of the car battery.
5 Press to turn on the power.
6 Detach the faceplate and reset the unit. ( 3)
INSTALLATION/CONNECTION
JS_JVC_KD_R980BTS_K_EN_4.indd 33 20/5/2016 2:22:55 PM