ENGLISH FRANÇAIS ESPAÑOL KD-T925BTS / KD-T920BTS / KD-T720BT CD RECEIVER INSTRUCTION MANUAL RÉCEPTEUR CD MANUEL D’INSTRUCTIONS RECEPTOR CON CD MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-3880-00 [K] KD_T925BTS_K_B5A-3880-00_Cover_3rd Draft.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
ISED Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents. Article 5 1. 2. 2.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Contents Before Use ................................................................................................. 3 References .............................................................................................. 33 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate Attach Volume knob Loading slot Display window* Detach How to reset Reset the unit within 5 seconds after detaching the faceplate. KD-T925BTS: USB cable from the rear of the unit Detach button * Only for illustration purpose. To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Press the volume knob to mute the sound or pause playback. • Press again to cancel.
Getting Started Basics Remote control (RM-RK52) (for KD-T925BTS/KD-T920BTS) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) 1 Pull out the insulation sheet when using for the first time. How to replace the battery When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 6), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” “VOLUME KNOB” “TO CONFIRM”.
Getting Started To set the date 7 Turn the volume knob to select [DATE SET], then press the knob. 8 Turn the volume knob to make the settings, then press the knob. Set the date in the order of “Day” “Month” “Year”. 9 Press to exit. To return to the previous setting item, press 3 [UPDATE SYSTEM] [F/W UP xxxx] . [FACTORY RESET] Set the basic settings . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then press the knob.
Radio Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. Other settings Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T (or press H / I on the remote control) to search for a station automatically. (or) Press and hold S / T (or press and hold H / I on the remote control) until “M” flashes, then press repeatedly to search for a station manually. .
CD/USB/iPod Radio [AREA] [N.AMERICA]: For North/Central/South America, AM/FM intervals: 10 kHz/200 kHz. ; [S.AMERICA]: For some South American countries, AM/FM intervals: 10 kHz/50 kHz. ; [EUROPE]: For any other areas, AM/FM intervals: 9 kHz/50 kHz. [PTY SEARCH] Select a PTY code for FM Radio Broadcast Data Sytem (see the following “PTY code for FM Radio Broadcast Data System”). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
CD/USB/iPod Connect an iPod/iPhone USB input terminal Accessory of the iPod/iPhone* iPod/ iPhone To On the faceplate On the remote control Reverse/ Fast-forward Press and hold S / T. Press and hold H / I. Select a track/file Press S / T. Press H / I. Select a folder* Press 2 J / 1 K. Press J / K. Repeat play Press 4 B repeatedly. and/or [TRACK REPEAT]/[ALL REPEAT]: Audio CD KD-T925BTS: You can also connect to the USB cable from the rear of the unit (USB input terminal).
CD/USB/iPod Default: [XX] Select music drive While in USB FRONT/USB REAR/USB source, press 5 MODE repeatedly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. (This unit can support multiple drive device of up to 4 drives. However, this unit may take some time to read if three or more cards are connected.
AUX CD/USB/iPod Alphabet search (applicable only for iPod FRONT/iPod REAR/iPod USB source and iPod BT source) You can search for a file according to the first character. 1 Press . 2 Turn the volume knob to select a list, then press the knob. 3 Press 2 J / 1 K or turn the volume knob quickly to select the desired character (A to Z, 0 to 9, OTHERS). Select “OTHERS” if the first character is other than A to Z, 0 to 9. 4 Press the volume knob to start searching.
SiriusXM® Radio (for KD-T925BTS/KD-T920BTS) Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . Preparation: 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
SiriusXM® Radio (for KD-T925BTS/KD-T920BTS) Settings in memory You can store up to 18 channels. Store a channel While listening to a channel... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob. The preset number flashes and “MEMORY” appears. During Replay... To On the faceplate On the remote control Play back/pause Press the volume knob. Press d.
SiriusXM® Radio (for KD-T925BTS/KD-T920BTS) Using SiriusXM Vehicle Tuner later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites. • “ ” appears following the last character of the channel name for the SmartFavorites channels. * When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
SiriusXM® Radio (for KD-T925BTS/KD-T920BTS) [CODE SET] [LOCK SETTING] [CHANNEL EDIT]*1 1 2 3 4 5 • Turn the volume knob to select a number. Press S / T to move to the entry position. Repeat step 1 and step 2 to enter a new 4-digit pass code. Press the volume knob to confirm. Repeat step 1 to step 4 to reconfirm the pass code. Make a note of the new pass code to enter channel lock settings for next time. [MATURE CH]: Selects the SiriusXM-defined lock setting.
Bluetooth® JVC Remote Application Default: [XX] [REMOTE APP] [SELECT] [IOS] Selects the device ([IOS] or [ANDROID]) to use the application. [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels. If [IOS] is selected, select iPod BT source (or iPod FRONT/iPod REAR/iPod USB source if your iPhone/iPod touch is connected via USB input terminal) to activate the application.
Bluetooth® Pair and connect a Bluetooth device for the first time 1 Press B SRC to turn on the unit. 2 Search and select the name of your receiver (“KD-T925BTS”/ “KD-T920BTS“/“KD-T720BT”) on the Bluetooth device. “BT PAIRING” flashes on the display. • For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching. 3 Perform (A) or (B) depending on what appears on the display.
Bluetooth® Bluetooth — Mobile phone The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. End a call Press and hold or the volume knob. Press and hold J / K / H / I. First incoming call...
Bluetooth® *1 This adjustment will not affect the volume of the other sources. *2 Press and hold VOL + to continuously increase the volume to 15. *3 Operations may vary according to the connected Bluetooth device. Default: [XX] [SETTINGS] [AUTO ANSWER] [01 SEC] to [30 SEC]: Answers an incoming call automatically in the selected time (in seconds). ; [OFF]: Cancels. Improve the voice quality While talking on the phone...
Bluetooth® [RECENT CALL] [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode.
Bluetooth® Default: [XX] [BT MODE] [PHONE SELECT] [AUDIO SELECT] Selects the phone or audio device to connect or disconnect. “ ” appears in front of the device name when connected. “ ” appears in front of the current playback audio device. • You can connect a maximum of two Bluetooth phones and one Bluetooth audio device at a time. [DEVICE DELETE] 1 Turn the volume knob to select a device to delete, then press the knob. 2 Turn the volume knob to select [YES] or [NO], then press the knob.
Bluetooth® The connectivity result flashes on the display. “PAIRING OK” and/or “HANDS-FREE OK”*1 and/or “AUD.STREAM OK”*2 and/ or “PBAP OK”*3: Compatible *1 Compatible with Hands-Free Profile (HFP) *2 Compatible with Advanced Audio Distribution Profile (A2DP) *3 Compatible with Phonebook Access profile (PBAP) Bluetooth — Audio • Operations and display indications may differ according to their availability on the connected device.
AMAZON ALEXA Bluetooth® To Repeat play On the faceplate Press 4 B repeatedly. [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT], [REPEAT OFF] Random play Press 3 A repeatedly. [GROUP RANDOM], [ALL RANDOM], [RANDOM OFF] Select a file from a folder/list Refer to “Select a file to play” on page 10. Switch between connected Bluetooth audio devices Press 5. (Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.
AMAZON ALEXA Option B: Manual Pairing 1 Start up the Alexa mobile application and go to the “Devices” tab. 2 Tap the “ + “ icon at the top right corner. 3 Tap “Add Device”. 4 Tap “Automotive Accessory” or “Headphones” from the list of device types. 5 Tap the name of your receiver (“KD-T925BTS”/“KD-T920BTS”/ “KD-T720BT”) and follow the instructions. Once the setup process is completed, the Alexa mobile application will establish a connection with this unit.
AMAZON ALEXA • To return to the previous source before ALEXA, press B SRC (or press SOURCE on the remote control). • To activate Alexa, press or speak “Alexa”. • To cancel current listening state, press . • To cancel current thinking/speaking states and go to listening state, press or speak “Alexa”. • Only one Alexa connection can be connected at one time.
Audio Settings [PRO EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
Audio Settings [FADER] (Not applicable when 3-way crossover is selected.) [POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front and rear speaker output balance. [BALANCE]*4 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance. [VOLUME ADJUST] [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level of each source by comparing to the FM volume levels. (Before adjustment, select the source you want to adjust.
Audio Settings KD-T720BT: Speaker output settings [SPK/PRE OUT] (Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (page 27) Setting on [SPK/PRE OUT] Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method. [REAR/REAR] Audio signal through lineout terminal REAR/SW Rear speakers output [REAR/SUB.W] (default) Subwoofer output Connection via lineout terminals [SUB.W/SUB.
Audio Settings Crossover settings Below are the available setting items for 2-way crossover and 3-way crossover. 2-way crossover setting items [SPEAKER SIZE] [FRONT] [SIZE] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [TWEETER] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) CAUTION Select a crossover type according to how the speakers are connected. (Page 41, 42) If you select a wrong type: • The speakers may be damaged.
Audio Settings [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] to [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Audio Settings Digital Time Alignment settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings Zone identification for brightness settings 4 Press KD-T925BTS/KD-T920BTS: To return to the previous setting item, press to exit. . Default: [XX] [DISPLAY] [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting. (See the following “[BRIGHTNESS]” settings.) [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer.
Display Settings [COLOR] (for KD-T925BTS/KD-T920BTS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 32.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds.
References • DualDisc playback: The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended. • For detailed information and notes about the playable audio files, visit . Playable files • Disc: Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.
References Change the display information Source name Display information: Main (Supplementary) For MP3/WMA/AAC/WAV/FLAC files: Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) File name (Folder name) File name (Date) Playing time (Date) back to the beginning Each time you press , the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg.
Troubleshooting Symptom Radio Symptom Remedy Playback order is not as intended. Optical disc, the files are played in the order which they were recorded. USB device, the folders are played in the order of creation (date and time). The files within each folder are played in the order of the file name (alphabet). “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.
Troubleshooting SiriusXM® Radio This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod USB again. “iPod ERROR” • Reconnect the iPod. • Reset the iPod. • Press and hold B SRC to turn off the power. Turn the power on again for error recovery.
Troubleshooting AMAZON ALEXA Bluetooth® The connected Bluetooth audio player cannot be controlled. 38 Remedy Symptom • Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.) • Disconnect and connect the Bluetooth player again. “PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again.
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. Part list for installation (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting.
Installation/Connection Installing the unit (in-dash mounting) Do the required wiring. (Page 41) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car Bend the appropriate tabs to hold the sleeve firmly in place. Installing the unit (without mounting sleeve) Removing the unit 1 Remove the mounting sleeve and trim plate from the unit.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) No Part 1 For KD-T925BTS: USB cable (DC 5 V 1.5 A) (approx. 1 m/3.3 feet) To remote lead (blue/white) of the wiring harness. (Page 41) 2 Output terminals (See “Connect external amplifiers via output terminals”.) 3 Microphone input jack (page 16) 4 For KD-T925BTS/KD-T920BTS: Expansion port (12 V available).
Specifications 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Usable Sensitivity (S/N = 30 dB) AM Frequency Range CD player 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 29 dBμ (28.2 μV) USB Standard USB 1.1, USB 2.
Version Bluetooth V4.2 Frequency Range 2.402 GHz — 2.480 GHz 13 Band Frequency 62.5/ 100/ 160/ 250/ 400/ 630/ 1k/ 1.6k/ 2.5k/ 4k/ 6.3k/ 10k/ 16k Hz Level -09 — +09 (-9 dB — +9 dB) Q 1.35/ 1.5/ 2.0 Frequency THROUGH/ 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/ 120/ 150/ 180/ 220/ 250 Hz Level -6/ -12/ -18/ -24 dB/Oct.
• Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
ENGLISH FRANÇAIS ESPAÑOL KD-T925BTS / KD-T920BTS / KD-T720BT CD RECEIVER Quick Start Guide RÉCEPTEUR CD Guide de démarrage rapide RECEPTOR CON CD Guía de inicio rápido For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE INSTRUCCIONES en el siguiente sitio web
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
ISED Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Use only the specified screws. Using wrong screws might damage the unit. Join the same color wires together.
Before Use Basics (on faceplate) IMPORTANT Volume knob Loading slot Display window*1 Auxiliary input jack • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference. WARNING Do not operate any function that takes your attention away from safe driving.
Getting Started 3 Set the basic settings 1 Acknowledge the crossover type and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” “VOLUME KNOB” “TO CONFIRM”. 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
Radio Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T to search for a station automatically. (or) Press and hold S / T until “M” flashes, then press repeatedly to search for a station manually. Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station.... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes.
Menu Settings Examples of some well-used settings 1 2 3 4 1 Press and hold Subwoofer Level Setting Press and hold to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
8 Press to exit the setting menu. Note: For KD-T920BTS/KD-T720BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings. Illumination Color Setting For KD-T925BTS/KD-T920BTS, you can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
