ENGLISH FRANÇAIS ESPAÑOL KD-T92MBS / KD-T721BT / KD-TD72BT / KD-SR87BT CD RECEIVER INSTRUCTION MANUAL RÉCEPTEUR CD MANUEL D’INSTRUCTIONS RECEPTOR CON CD MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-3834-00a [K] KD_T92MBS_K_B5A-3834-00a_Cover_5th Draft.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
ISED Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents. Article 5 1. 2. 2.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Contents Before Use ................................................................................................. 3 References .............................................................................................. 32 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate Attach KD-T92MBS: Volume knob Loading slot Display window* Detach Detach button How to reset KD-T721BT/KD-TD72BT/KD-SR87BT: Reset the unit within 5 seconds after detaching the faceplate. * Only for illustration purpose. To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Press the volume knob to mute the sound or pause playback. • Press again to cancel.
Getting Started Basics Remote control (RM-RK52) (for KD-T721BT) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) 1 Pull out the insulation sheet when using for the first time. How to replace the battery When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 6), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” “VOLUME KNOB” “TO CONFIRM”.
Getting Started To set the date 7 Turn the volume knob to select [DATE SET], then press the knob. 8 Turn the volume knob to make the settings, then press the knob. Set the date in the order of “Day” “Month” “Year”. 9 Press to exit. To return to the previous setting item, press 3 . [USER S.REMO] [F/W UPDATE]*2 [UPDATE SYSTEM] [F/W UP xxxx] Set the basic settings . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then press the knob.
Radio Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. Other settings Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T (or press H / I on the remote control) to search for a station automatically. (or) Press and hold S / T (or press and hold H / I on the remote control) until “M” flashes, then press repeatedly to search for a station manually. .
Radio [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select [SSM 07–12]/[SSM 13–18] to store the following 12 stations. [IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; [WIDE]: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
Radio • If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin is turned on.
CD/USB/iPod Connect an iPod/iPhone USB input terminal Accessory of the iPod/iPhone* iPod/ iPhone To On the faceplate On the remote control Reverse/ Fast-forward Press and hold S / T. Press and hold H / I. Select a track/file Press S / T. Press H / I. Select a folder* Press 2 J / 1 K. Press J / K. Repeat play Press 4 B repeatedly. [TRACK REPEAT]/[ALL REPEAT]: Audio CD The source changes to iPod USB automatically and playback starts. • You can also connect iPod/iPhone via Bluetooth.
CD/USB/iPod Quick search (applicable only for CD source and USB source) Select music drive While in USB source, press 5 MODE repeatedly. If you have many files, you can search through them quickly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. (This unit can support multiple drive device of up to 4 drives.
AUX SiriusXM® Radio (for KD-T92MBS) You can listen to music from a portable audio player via the auxiliary input jack. Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit .
SiriusXM® Radio (for KD-T92MBS) Start listening 1 Press B SRC repeatedly to select SIRIUS XM. 2 Press . “ ” indicator lights up. 3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob. If “ALL CHANNELS” is selected, all the available channels will be shown. 5 Turn the volume knob to select a channel, then press the knob. • Pressing and holding 1/2 changes the channel rapidly.
SiriusXM® Radio (for KD-T92MBS) SiriusXM Replay™ While listening to a channel... Using SiriusXM Vehicle Tuner later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites. • “ ” appears following the last character of the channel name for the SmartFavorites channels. * 1 Press the volume knob. “ ” indicator lights up and the unit memorizes this paused position. 2 Press the volume knob to start Replay.
SiriusXM® Radio (for KD-T92MBS) TuneScan™ [CODE SET] 1 2 3 4 5 • [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob. 2 Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number. 3 Press and hold to exit.
JVC Remote Application You can control the JVC car receiver from iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth) using JVC Remote application. • For more information, visit . Preparation: Install the latest version of JVC Remote application on your device before connecting. Default: [XX] [REMOTE APP] [SELECT] [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels.
Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. • Be sure to turn on the Bluetooth function of the device to make the following operations. • Signal conditions vary depending on the surroundings.
Bluetooth® • This unit supports Secure Simple Pairing (SSP). • Up to five devices can be registered (paired) in total. • Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, see [DEVICE DELETE] on page 21. • A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time. To connect or disconnect the registered device, see [PHONE SELECT] or [AUDIO SELECT] in [BT MODE].
Bluetooth® The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Improve the voice quality First incoming call... Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. Press and hold or the volume knob. Press and hold J / K / H / I. End a call *1 This adjustment will not affect the volume of the other sources.
Bluetooth® Default: [XX] [RECENT CALL] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press 2 J / 1 K to select the desired letter (A to Z, 0 to 9, and OTHERS).
Bluetooth® Default: [XX] Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK] or [BT MODE] [PHONE SELECT] [AUDIO SELECT] [DIAL NUMBER], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6).
Bluetooth® Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING PHONE” “PIN IS 0000” scrolls on the display. 2 Search and select the name of your receiver (“KD-T92MBS”/ “KD-T721BT”/“KD-TD72BT”/“KD-SR87BT”) on the Bluetooth device within 3 minutes.
Bluetooth® Bluetooth — Audio To • Operations and display indications may differ according to their availability on the connected device. • Depending on the connected device, some features may not work with your device. Repeat play While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. Listen to the audio player via Bluetooth On the faceplate On the remote control Press 4 B repeatedly.
Audio Settings [PRO EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
Audio Settings [FADER] (Not applicable when 3-way crossover is selected.) [POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front and rear speaker output balance. [BALANCE]*4 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance. [VOLUME ADJUST] [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level of each source by comparing to the FM volume levels. (Before adjustment, select the source you want to adjust.
Audio Settings KD-T721BT: Speaker output settings [SPK/PRE OUT] (Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (page 25) Setting on [SPK/PRE OUT] Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method. [REAR/REAR] Audio signal through lineout terminal REAR/SW Rear speakers output [REAR/SUB.W] (default) Subwoofer output Connection via lineout terminals [SUB.W/SUB.
Audio Settings Crossover settings Below are the available setting items for 2-way crossover and 3-way crossover. 2-way crossover setting items [SPEAKER SIZE] [FRONT] [SIZE] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [TWEETER] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) CAUTION Select a crossover type according to how the speakers are connected. (Page 40, 41) If you select a wrong type: • The speakers may be damaged.
Audio Settings [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] to [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Audio Settings Digital Time Alignment settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings Zone identification for brightness settings 4 Press KD-T92MBS: To return to the previous setting item, press to exit. . Default: [XX] [DISPLAY] [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting. (See the following “[BRIGHTNESS]” settings.) [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer.
Display Settings [COLOR] (for KD-T92MBS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 30.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds.
Learning Steering Remote Control (for KD-T721BT) 6 Press and hold any control keys on your steering remote control which you want to assign. A list of key functions will appear on the display. [NONE] (default)/[MUTE]/[SEEK UP]/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/[MODE]/ [ON HOOK]/[OFF HOOK]/[VOICE]/[ENTER] 7 Turn the volume knob to select a function to assign, then press the knob. The selected key function is assigned to the steering remote control key you have selected in step 6.
References • DualDisc playback: The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended. • For detailed information and notes about the playable audio files, visit . Playable files • Disc: Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.
References Change the display information Source name Display information: Main (Supplementary) For MP3/WMA/AAC/WAV/FLAC files: Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) File name (Folder name) File name (Date) Playing time (Date) back to the beginning Each time you press , the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg.
References KD-T721BT/KD-TD72BT/KD-SR87BT: Main display Clock display Source name Display information: Main FM or AM Frequency Frequency with Music Synchronization Effect* back to the beginning Date Source name Display information: Main BT AUDIO Song title/Artist Song title/Artist with Music Synchronization Effect* Album title/Artist Playing time Date back to the beginning AUX Source name Source name with Music Synchronization Effect* Date back to the beginning * During Music Synchronization Effec
Troubleshooting Symptom Radio CD/USB/iPod Symptom Remedy Playback order is not as intended. Optical disc, the files are played in the order which they were recorded. USB device, the folders are played in the order of creation (date and time). The files within each folder are played in the order of the file name (alphabet). “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.
Troubleshooting This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod USB again. “MEMORY FULL” You have reached the maximum storage limit of your iPod/iPhone. “CH LOCKED LOCK CODE?” The selected channel is locked. Enter the correct pass code to unlock.
Installation/Connection Troubleshooting Symptom Bluetooth® The connected Bluetooth audio player cannot be controlled. Remedy • Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.) • Disconnect and connect the Bluetooth player again. “PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again.
Installation/Connection Part list for installation Installing the unit (in-dash mounting) (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Do the required wiring. (Page 40) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (E) Extraction key (×2) Bend the appropriate tabs to hold the sleeve firmly in place.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) No Part 1 For KD-T721BT: Learning steering remote (page 31) To remote lead (blue/white) of the wiring harness. (Page 40) 2 Output terminals (See “Connect external amplifiers via output terminals”.) 3 Microphone input jack (page 17) 4 For KD-T92MBS: Expansion port (12 V available).
Specifications 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB CD player Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Usable Sensitivity (S/N = 30 dB) AM Frequency Range 42 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 29 dBμ (28.2 μV) USB Standard USB 1.
Version Bluetooth V4.2 Frequency Range 2.402 GHz — 2.480 GHz 13 Band Frequency 62.5/ 100/ 160/ 250/ 400/ 630/ 1k/ 1.6k/ 2.5k/ 4k/ 6.3k/ 10k/ 16k Hz Level -09 — +09 (-9 dB — +9 dB) Q 1.35/ 1.5/ 2.0 Frequency THROUGH/ 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/ 120/ 150/ 180/ 220/ 250 Hz Level -6/ -12/ -18/ -24 dB/Oct.
• Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
ENGLISH FRANÇAIS ESPAÑOL KD-T92MBS / KD-T721BT / KD-TD72BT / KD-SR87BT CD RECEIVER Quick Start Guide RÉCEPTEUR CD Guide de démarrage rapide RECEPTOR CON CD Guía de inicio rápido For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE INSTRUCCIONES en el siguiente
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
ISED Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Use only the specified screws. Using wrong screws might damage the unit. Join the same color wires together.
Before Use Basics (on faceplate) IMPORTANT *1 Only for illustration purpose. • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference.
Getting Started 3 Set the basic settings 1 Acknowledge the crossover type and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” “VOLUME KNOB” “TO CONFIRM”. 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
Radio Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T to search for a station automatically. (or) Press and hold S / T until “M” flashes, then press repeatedly to search for a station manually. CD/USB/iPod Selectable source: • CD/USB/iPod USB or iPod BT Start playback The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone) to the USB input terminal.
Menu Settings Examples of some well-used settings 1 2 3 4 1 Press and hold Subwoofer Level Setting Press and hold to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
8 Press to exit the setting menu. Note: For KD-T721BT/KD-TD72BT/KD-SR87BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings. Illumination Color Setting For KD-T92MBS, you can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
