JVC KW-V220BT KW-V120BT KW-V420BT KW-V320BT MONITOR WITH DVD RECEIVER INSTRUCT ION MANUAL JVCKENWOOD Corporation This instruction manual is used to describe models listed below. Model availability and features (functions) may differ depending on the country and sales area. ·Region 1 (DVD Regio n Code 1 area) ·Region 4 (DVD Reg ion Code 4 area) IfIJI ...
BEFORE USE ............................................................ 2 How to reset your unit.. .................................................. 3 INITIAL SETTINGS .................................................. 4 Initial setup ......................................................................... 4 Clock settings .................................................................... 4 BASICS .................................................................... 5 Component names and functions ......
For KW-V420BT Region 1/KW-V320BT Region 1/ KW-V220BT Region 1/KW-V120BT: IC (Industry Canada) Notice For KW-V420BT Region 1/KW-V320BT Region 1/ KW-V220BT Region 1/KW-V120BT: 6CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, the following are reproductions of labels on, or inside the product relating to laser product safety.
(Page 56) (Page 57) Initial setup When you power on the unit for the first time or reset the unit, the initial setting screen appears. • You can also change the settings on the screen. (Page 55) 1 Perform the initial settings. * * (Page 7) (Page 21) (Page 35) (Page 51) Activate or deactivate the display demonstration. Select the text language used for on-screen information.
I~IIIAL SEIT.!z!lN~G~S~iiiiZ=:~~~iZICilll 3 Set the clock time. BASICS Component names and fundions - & Caution on the volume setting: Digital devices produce very little noise compared with other sources. Lower the volume before playing these digital sources to avoid damaging the speakers by sudden increase ofthe output level. KW-V420BT Synchronizes the clock time with FM RBDS. Sets the clock manually. (See below.
KW-V320BT lE i-Sl Volume+/- button Adjusts the audio volume. (Page 7) Monitor panel* Screen (touch panel) * You can change the color of the buttons on the monitor panel. (Page 51) KW-V220BT /KW-V120BT OJ C) button • Turns on the power. (Press) (Page 7) • Turns off the power. (Hold) (Page 7) Pops up the short-cut menu. (Press) (Page 11) [I] Reset button Resets the unit. (Page 3) W Loading slot W HOME/\fJ button • Displays the Home screen. (Press) (Page 9) • Activates the voice dialing.
BASICS 0 Adjusting the volume Common operations To adjust the volume (00 to 35) KW-V420BT 0 Turning on the power KW-V420BT KW-V320BT KW-V220BT KW-V120BT VOLUME 1- KW-V420BT) 1 Display the screen. On the Home screen: • Press [VJ repeatedly to change the page on the menu screen. ~ KW-V320BT 0 Adjusting the panel angle (only for KW-V220BT KW-V120BT 0 Turning off the power KW-V420BT KW-V320BT H:MESSh ~ ..
BASICS 0 Turning off the screen 0 Turning on/off the AV source On the pop-up short-cut menu (Page 11 ): Display the pop-up short-cut menu by pressing FNC (for KW-V420BT/KW-V220BT/KW-V120BT) or 0 (for KW-V320Bn on the monitor panel, then select [Display OFF]. You can activate the AV function by selecting a source on the Home screen. KW-V420BT/KW-V220BT/KW-V120BT I D 'i.'10:28 USB ' II ;' Title Name 1 Artist Name o Album Title 00:10•28 ... ~; ; ; ; On the monitor panel: KW-V420BT KW-V320BT ..
BASICS Gesture control on the source control screen: You can also control playback by moving your finger on the touch panel as follows (for some sources, the gesture control is not available). • Sliding the finger towards up/down: Functions same as pressing fbl • Sliding the finger towards left/right: Functions same as pressing [~]/[~] . • Moving your finger clockwise or counterclockwise: increases/decreases the volume. ri::IJ Home screen Displays the source control screen and settings screen.
BASICS OTouch screen operations Selecting the playback source [AV-IN]* 1 On the Home screen: 3 [Apps] ~ [PANDORA]* 2 OJ [SiriusXM]* 3 Displays the video control menu while playing a video. [Maestro]*4 Switches to an external component connected to the iPod/AV-IN input terminal. (Page 37) Switches to the App screen from the connected iPod touch/iPhone/ Android device. (Page 23) Switches to the Pandora broadcast. (Page 24) Switches to the SiriusXM®radio broadcast.
BASICS 0 Selecting the playback source on the Home screen •••• •••• "'"'"'~ .n All St~Uing-o;, ~ Tuner 10:28 (. AM Phone ti tJ!!:: iPod ... Now PIJytng Using the pop-up short-cut menu While displaying the source control screen, you can jump to the other screen from the pop-up short-cut menu. 1 Display the pop-up short-cut menu. * BTAud~ ~ KW-V420BT KW-V320BT KW-V220BT/ KW-V120BT FNC~ • You can change the items to display on the Home screen.
Playing a disc • If a disc does not have a disc menu, all tracks on it will be played repeatedly until you change the source or eject the disc. • For playable disc types/file types, see page 67. 0 Ejecting a disc KW-V420BT KW-V220BT KW-V120BT 0 Inserting a disc Insert a disc with the label side facing up. KW-V420BT KW-V320BT Press [~] on the Home screen or "DISC" source control screen.
DISCS Operation buttons • Available buttons on the screen and operations differ depending on the type of disc/file being played back. [ ~ ]/[ [E ]* Displays the other operation button window. • To hide the window, press [ ~)/[~)*. [;iili1 Displays the screen. (Page 47) [Q] Displays the folder/track list. (Page 14) [~] [~] • Selects a chapter/track. (Press) • Reverse/forward search. (Hold) • Plays in slow-motion during pause. (Hold) Starts/pauses playback. [...
DISC~S~~==~ --=~==~--~~==~======~~==~~==~ma~~======~====~==~ 0 Selecting a folder/track on the list 0 Video menu operations 1 You can display the video menu screen during video playback. • The operation buttons disappear when the screen is touched or when no operation is done for about 5 seconds. l0MENU] [T MENU] [Highlight] [CUR] 2 Select the folder (G)), then the item in the selected folder (@ ). Repeat the procedure until you select the desired track. It:- A\'10:28 fJ DISC ·~ t:. II rolrtP.
DISCS To select a track directly on a VCD • When playing a VCD with PBC activated, stop playback to deactivate the PBC function, then use the direct selecting buttons to select a track number. ForVCD l0MENU] Displays the disc menu. [Audio] Selects the audio channel (ST: stereo, L: left, R: right). Displays/hides the direct selection buttons. (See the right column.) Displays the previous screen or menu. Displays the picture size selection screen. (Page 51) Selects the aspect ratio.
DISCS Settings for disc playback-< DISC Mode> 1 2 • Available items shown on the screen differ depending on the type of disc/file being played back. 16 0 Setting items
u,SB +- +ii&* %6 &¥¥%* Connecting a USB device You can connect a USB mass storage class device such as a USB memory, Digital Audio Player etc. to the unit. • For details about connecting USB devices, see page 63. • You cannot connect a computer or portable HDD to the USB input terminal. • For playable file types and notes on using USB devices, see page 68. When a USB device is connected ... The source changes to "USB" and playback starts.
, d¥t ni"-? +r 2 0 Settings for USB playback-< USB Mode> 2 Jt nMHii d*rr ,.; wwa d*t % !if31£- S&d£9&3 i 6 1 * Select the playback file type when a disc contains different types of files. • Audio: Plays back audio files. • Still Image: Plays back picture files. • Video: Plays back video files. • Audio&Video (initial): Plays back audio files and video files.
Andr.oid Preparation 0 Installing JVC Music Play Install the AndroidTM application JVC Music Play on your Android device beforehand. • When a compatible Android device is connected, "Press [VIEW] to install JVC MUSIC PLAY APP" is shown on the Android device. Follow the instructions to install the application. You can also install the latest version of the JVC Music Play application on your Android device before connecting. About JVC Music Play • This unit supports the AndroidTM application JVC Music Play.
0 Selecting a track from the menu 1 0 Settings for playback on the Android device- Shows/hides artwork of the Android device. 1 • AUTO MODE: Controls from the unit (using the JVC Music Play application). • AUDIO MODE: Controls other media player applications from the Android device (without using the JVC Music Play application). - You can play/pause or skip files from the unit. 2 Select a category (G)), then a desired item (@ ).
iP-odli P-hone Preparation 0 Connecting iPod/iPhone 0 Selecting the connection method of iPod/iPhone 1 1 On the Home screen: • For details about connecting iPod/iPhone, see page 63. • For playable iPod/iPhone types, see page 68. s.n.~l 0:28 :::: .fj An Connect your iPod/iPhone according to your purpose or the type of iPod/iPhone. To listen to music: - For Lightning connector models: Use USB Audio cable for iPod/iPhone-KS-U62.
Playback operations When the operation buttons are not displayed on the screen, touch the area shown on the illustration. • To change settings for video playback, see page 50. 0 Indications and buttons on the source control screen Operation buttons [ ~ ]/[ (!] ]*1 [sillil Displays the other operation button window. • To hide the window, press [ ~)1[~)* 1 • Displays the screen. (Page 47) Displays the audio/video file list. (See the right column.) [~] [~] • Selects a track.
You can use an App of the connected iPod touch/ iPhone/Android on this unit. • For Apps you can use on this unit, visit . Preparation 1 Connect the iPod touch/iPhone/Android. • For Android: Connect the Android device via Bluetooth. (Page 38) · For iPod touch/iPhone: Connect iPod touch/ iPhone with a cable. (Page 63) - Be sure to select the appropriate connection method of iPod touch/iPhone on .
You can stream Pandora from iPod touch/iPhone or Android devices. Install the latest version of the Pandora application on your iPod touch/iPhone/Android. Preparation 1 Connect the device. Playback operations You can operate Pandora using the remote controller*1 • Only playing, pausing, and skipping are available. 0 Indications and buttons on the source control screen • For Android: Connect the Android device via Bluetooth. (Page 38) • For iPod touch/iPhone: Connect iPod touch/ iPhone with a cable.
® 0 Selecting a station from the list 1 Display the list selection screen. You can change the page to display more items by pressing [..6._]/[VJ. indicator appears on the left of the • The item when Shuffle is activated. (All songs in the registered stations are played randomly.) indicator appears on the right of the • The item when the station is shared. AndroidTM • Visit Google play and search for "Pandora" to install. • Bluetooth must be built in and the following profiles must be supported.
Listening to the radio "" 0 Indications and buttons on the source Operation buttons [~]/[(E]* 1 control screen [AM] [FM] Displays the other operation button window. • To hide the window, press [~)I [[il]*1. Selects the AM band. Selects the FM band. r:FM1~FM2~FM3] Displays the preset station window. (Page 27) • To hide the window, press • Selects a stored station. (Press) • Stores the current station. (Hold) Displays the screen. (Page 47) Enters PTY search mode. (Page 28) [h [P1]- [PS] ...
Presetting stations 0 Storing stations in the memory You can preset 5 stations for each band. Manual presetting 0 Selecting a preset station 1 Tune in to a station you want to preset. For KW-V420BT/KW-V220BT/KW-V120BT: (Page 26) 1 2 Select a preset number. Select the band (G)), then display the set station window ((I)). Automatic presetting-SSM (Strong-station Sequential Memory) The station selected in step 1 is stored. • You can also select a preset station by pressing [P1]- [PS].
0 Searching for FM RBDS programs-PlY 0 Activating/deactivating Tl Standby Reception Search You can search for your favorite programs being broadcast by selecting the PTY code. 1 2 Select a PTY code. The unit is in standby to switch to Traffic Information (TI) if available. (The Tl indicator lights up in white.) • If the Tl indicator is lit in orange, tune into another station providing RBDS signals. To deactivate Tl Standby Reception: Press [TI]. (The Tl indicator turns off.
Only SiriusXM®brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. 3 When the following screen appears, press [Return].
Sir,i.usXM:.S.atellite.Badi.o Operation buttons [SXM1 1Selects the band. [SXM4] SXM 1-.- SXM2 _.. SXM3-.. SXM4 J L [~ ]/[(!]]*1 Displays the other operation button window. • To hide the window, press[~]/ [Song Title]/ [Info]! [Category] Changes the displayed information each time this button is pressed. [ ~]*2 Displays the preset channel window. (See the far right column.) • To hide the window, press[~]. [[!IJ*l. [li&liJ [QJ [~II] [CHT]I[CH.&.
Selecting a channel Replay 0 Selecting a channel on the list You can obtain information on channels or select a category and then a channel. 1 Display the screen. 2 Select a category (G)), and then select a channel (@ ). • You can change the page to display more items by pressing [,6.]/[Vl. • To list all the channels, select [All Channels]. -·~ .\ ':1 ))PI L S' • ''"~'''·'•"''- ' 10 7R ''.
Sir,i.u sXM!.Satellite,Badio Smartfavorites User stored channels (P1 toPS) of current band are recognized as SmartFavorites channels. SiriusXM Connect Vehicle Tuner automatically buffers their broadcast content in the background. When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content. • SmartFavorites is available only when you connect an SXV200 or later SiriusXM Connect Vehicle Tuner.
SiriusXM® Satellite Radio Setting reception restrictions 2 0 Setting the parental control Display the screen. You can limit access to SiriusXM channels, such as those with mature content. Dis the screen. [Enter] again to confirm the code.
Sir.iusXM® Satellite Ra!.!ldeio H=====================-= • You can change the page to display more items by pressing (.~]![VJ. • To list all the channels, select [All Channels). • A check mark appears beside the selected channel. Repeat this step if you want to set the lock on multiple channels. Selecting the channels to lock-Parental Lock Channel Selection This parental control option allows you to pick the channels to be locked by the parental control feature.
OJ.I:I.E.B.EX1.E.B,I)I.4 ,L COMJ~QI)I.E.I)IIS Using the rear view camera To display the picture from the rear view camera manually 3 • To connect a rear view camera, see page 64. • To use a rear view camera, a REVERSE lead connection is required. (Page 62) 0 Settings for the rear view camera 1 Display the settings screen. On the Home screen: [ON] [OFF] Displays the picture from the rear view camera when you shift the gear to the reverse (R) position.
OII:IER EXIERNAL CQM,I!QNENIS To adjust the picture While the camera screen is displayed ... 2 1 Display the screen. (See the far left column.) 2 Display the parking guidelines adjustment screen. 3 • The picture adjustment menu is displayed. (Page SO) To close the picture adjustment menu, touch the same area again. 0 Using the parking guidelines on the rear view screen You can display parking guidelines to enable easier parking when you shift the gear to the reverse (R) position.
Using external audio/video players-AV-IN 0 Changing the AV-IN name When the operation buttons are not displayed on the screen, touch the area shown on the illustration. • To change settings for video playback, see page 50. 1 You can change the AV-IN name displayed on the "AV-IN" source control screen. Display the
Information for using Bluetooth® devices 0 Bluetooth® - Bluetooth is a short-range wireless radio communication technology for mobile devices such as mobile phones, portable PCs, and other devices. Bluetooth devices can be connected without cables and communicate with each other. Notes • While driving, do not perform complicated operations such as dialing numbers, using the phone book, etc. When you perform these operations, stop your car in a safe place.
Pairing a Bluetooth device using a PIN code (for Bluetooth 2.0) 1 2 Change the PIN code. • If you wish to skip changing the PIN code, go to step 3. • The PIN code is initially set to "0000". • The maximum number of digits in the PIN code is 15. Display the screen. On the Home screen: 4 Select the unit ("Car Multimedia") on your Bluetooth device. • If a PIN code is required, enter "0000" (initial). When pairing is complete, the device is listed on the .
0 Connecting/disconnecting a registered Bluetooth device 4 Two devices can be connected simultaneously. 1 Select [ON] (to connect) or [OFF] (to disconnect) for the target (G)), then display the screen (@ ). Display the screen. (Page 39) • When a Bluetooth mobile phone is connected, the signal strength and battery level are displayed when the information is acquired from the device.
BLUEIOQilt Using a Bluetooth mobile phone 0 Ending a call While talking ... 0 Receiving a call 0 Switching between handsfree mode and phone mode While talking ... When a call comes in ... • Call information is displayed if acquired. • Phone operation is not available while the picture from the rear view camera is displayed. (Page 35) 0 Adjusting the volume of calls/earpiece/ microphone While talking ...
0 Sending text during a call 0 Making a call You can send text during a call using the DTMF (Dual Tone Multi Frequency) function. 1 Display the phone control screen. On the Home screen: For KW-V420BT/KW-V220BT/KW-V120BT: ;;;; n All * When the mobile phone is not compatible with Phone Book Access Profile (PBAP), the call history and the phone book are not displayed. From the call history/phone book/preset list 1 10:28 (..~ Vhon~q Sottlnt]!.
BLIJ.EJ,O.QI~i• To use the A to Z search in the phone book: 1 • To display other phone numbers: When the phone book list is displayed, you can switch between phone numbers if several phone numbers are registered for the same contact (up to 10 phone numbers per contact). 1 Switch the Voice dialing • Available only when the connected mobile phone has a voice recognition system. 1 Activate voice dialing. On the phone control screen: one number. 2 Select the initial.
BLUEIOOJ. 0 Presetting phone numbers You can preset up to 5 phone numbers. 1 Display the phone control screen. (Page 42) 2 Select hone book or call history. Using the Bluetooth audio player • To register a new device, see page 38. • To connect/disconnect a device, see page 40. 0 Indications and buttons on the source control screen Operation buttons [~ ]/[(!]]* 2 Displays the other operation button window. • To hide the window, press [ ~ JI[[!)J*2 • [;!i~i] Displays the screen.
c 0 Selecting an audio file from the menu d~UI 1 X'o~;er 1 lfl ,' ,'\I!QI'lfl10rll 1Sy$\em 2 Select a category (G)), then a desired item * BfAud•O ®J>:· ~ ~ '"" •• 10:28 • Select an item in each layer until you reach and select the desired file. • You can change the page to display more items by pressing [a]I[VJ. • Press [~] to return to the upper layer. • If you want to play all tracks in the folder, press [~] on the right of the desired folder.
Settings for using applications of iPod touch/iPhone/Android 1 Display the screen. On the Home screen: Before using applications of iPod touch /iPhone/ Android such as Pandora, select the device to use. 3 When selecting [Android/Other (Biuetooth)] as the device type: Select the Android device (G)), then press [OK] to connect (@ ). When connecting the device for first time, the setup screen (for connection, etc.) appears.
SEJ.J.INGS 0 Using the sound equalization • The adjustments are memorized for each source until you adjust the sound again. If the source is a disc, the adjustments are stored for each of the following categories. - DVDNCD -CD - DivX/MPEG 1/MPEG2/MP3/WMA/WAVI AAC • You cannot adjust the sound when the unit is in standby. 1 Select a sound mode. (See the left column.) 2 Select a band and adjust the level of the selected band. • You can adjust the level by dragging the slider or using [~]/[T].
SEJ.J.INGS 0 Setting the speakers-car type, 3 speaker size and crossover frequency Preparation: Select the appropriate crossover network mode beforehand. (Page 47) 1 Select the speaker type (G)), select the size of the selected speaker(@ ), then display the screen (@ ). Display the screen. On the Home screen: • When a speaker is not connected, select . • When setting the front speakers, also select the speaker size for .
SEJ.J.INGS 0 Adjusting the Digital Time Alignment 3 Select an item to make an adjustment. (DTA) Make fine adjustments to the delay time of the speaker output to create a more suitable environment for your vehicle. 1 Display the
SEJ.J.IMGS Adjustment for video playback 0 Adjusting the picture You can adjust the picture quality. 1 Display the picture adjustment screen. Adjusts the brightness.(- 15 to+ 15) Adjusts the contrast.(-10 to +10) 2 Select the aspect ratio. Adjusts the blackness.(-10 to + 10) On the source control screen: Adjusts the color.(- 10 to+ 10) Adjusts the tint.(- 10 to+ 10) Adjusts the sharpness.
0 Zooming the picture You can zoom the picture (, to ). • When is set to or (Page 50), the picture is zoomed with the aspect ratio of the setting. 1 Display the magnification level selecting screen. Changing the display design 3 Select a background/panel color* 1• To select a background You can change the background and panel color. 1 Display the screen. On the Home screen: :::: Sat~ a 0:28 J All <.
SEIII~GS 0 Making your own color adjustment (only for KW-V420BT/KW-V320BT) 1 Customizing the Home screen You can arrange the items to display on the Home screen. Select [Panel Color] on the screen. (Page 51) . , . . .::a • 2 1 Display the screen. On the Home screen: repeatedly to change the page on • Press the menu screen. rVJ ':> 3 Select the dimmer setting for the color (G)), then adjust the color(@).
SEIIINGS Customizing the system settings 0 Updating the system 2 You can update the system by connecting a USB device containing an update file. • To update the system, visit . 0 Memorizing/recalling the settings • You can memorize the settings changed in the menu and recall the memorized settings any time. • The memorized settings are kept even when the unit is reset. 1 1 • To connect a USB device, see page 63. Display the screen.
SET.IINGS 3 0 Adjusting the touch position You can adjust the touch position on the touch panel if the position touched and the operation performed do not match. 1 2 Touch the center of the marks at the upper left (G)), the lower center (@ ), then the upper right(@) as instructed. Display the screen. On the Home screen: • Press [VJ repeatedly to change the page on the menu screen. Updates the system application.
SEIII~GS 0
0 setting screen 1 * Select the text language used for on-screen information. • English (lnitiai)/Espanoi/Fran~ais/Deutsch/ ltaliano/Nederlands/Portugues/Ti.irk~e/ PyccKM171/~.,,~S:/...r".Ju/~~'ln1M-11nu/ f~H$:~3t/•R tfl 3t/Bahasa Malaysia/Bahasa Indonesia - For external monitors, only English/Spanish/ French/German/Italian/Dutch/Russian/ Portuguese are available. If another language has been selected, the text language for external monitors will be set to English.
For KW-V320BT Region 1/KW-V220BT Region 1I KW-V120BT: To use the remote controller, purchase RM-RK258 separately. ~ ~) CD CD CD Pl~pa·.ra,io.n·• 58 0 Changing the battery of the remote controller • Use a commercially available button battery (CR2025). • Insert the battery with the+ and- poles aligned properly. - If the effectiveness of the remote controller decreases, replace the battery. 6Caution: • Keep the battery out of reach of children and in original package until ready to use.
R OLLER Operations using . the remote controller (RM-RK258) 1-6 Enters preset station number. 0 Searching for an item directly ANGLE Tilts the monitor panel.* 3 Tuner frequency ASPECT Changes the aspect ratio. • To check the current aspect ratio setting, operate on the touch panel. (Page 50) 0 Basic button functions An Attenuates/restores the sound. DISP Switches the screen between the current source and the App screen from the connected iPod touch/iPhone/ Android. FM/A I AM/~ ~~ "V' I A...
&WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. & Precautions on installation and connection Mounting and wiring this product requires skills and experience.
co 0 Installation procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the battery. 8 2 Make the proper input and output wire 3 4 0 Installing the unit (only for KW-V420BT Region 4/KW-V320BT Region 4/ KW-V220BT Region 4) 0 Installing the trim plate (only for KW-V420BT Region 4/KW-V320BT Region 4/KW-V220BT Region 4) 1 Attach the trim plate ((I)). connections for each unit. Connect the speaker wires of the wiring harness.
0 Connecting wires to terminals See page 64. --:--------'-----'~ 10 Afuse I QQQQQnI :~~11 -----'1 1 ~....@~ ).l..ll-'--r---.,...-J( t~~~~~~~~~~~~~~~~~~~~~Connecttothevehicle~reverselampharness~hen using the optional rear vie~ camera. EXTI/F See page 64.* 1 * 1 Only for KW-V420BT Region 1IKW-V320BT Region 11 KW-V220BT Region 1. 2 for KW-V420BT Region 1IKW-V320BT Region 1. Only * 3 * Only for KW-V420BTIKW-V320BT. For 3 way speaker system connection, see also page 64.
c 0 Connecting a USB device 0 Connecting an Android device USB device (commercially available) iPod/iPhone (Lightning connector models) (commercially available) Android device (commercially available) t KW-V220BT tfifl KW-V120BT !U1J 1.0 m 0 Connecting iPod/iPhone (Front panel) 0 ~ ~ D D t } iPod/iPhone (30-pin connector models) (commercially available) ·~ ~O.Bm USB 2.0 cable (commercially available) J ~ ' t J 1.0 m KW-V220BT fFffi KW-V120BT tUtJ (Front panel) @) .
OConnecting external components 000000 1 * 1 When connecting an external amplifier/ connect its ground wire to 0 Connecting microphone for Bluetooth the chassis of the car; otherwise the unit may be damaged. * 2 Only for KW-V420BT Region 1/KW-V320BT Region 1/KW-V220BT Region 1. *3 Only for KW-V420BT Region 1/KW-V320BT Region 1. Connect the microphone (Q)) to the MIC terminal.
0 Removing the unit 1 0 Removing the trim plate 1 Engage the catch pins on the extraction key(@)) and remove the two locks on the lower part. Lower the frame and pull it forward. Remove the trim plate. (See the left column.) 2 Insert the two extraction keys (@)),then pull them as illustrated so that the unit can be removed. .., 2 Remove from the upper two catches. • Be careful to avoid injury from the catch pins on the extraction key. • The frame can be removed from the top side in the same manner.
OTo keep discs clean 0 Caution on cleaning the unit Do not use any solvent (for example, thinner, benzine, etc.), detergent, or insecticide. This may damage the monitor or the unit. Dirty discs may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from the center to the edge. ~~ . . ' Recommended cleaning method: Gently wipe the panel with a soft, dry cloth.
Playing JPEG files This unit can play back picture files with the extension code <.jpg> or <.jpeg>. This unit can play back files that are at 32 x 32 to 8 192 x 7 680 resolution. It may take time to display the file depending on its resolution. This unit can play back baseline JPEG files. Progressive JPEG files or lossless JPEG files cannot be played. Playing audio files (MP3/WMA/WAV/AAC) • This unit can play back files with the extension code <.mp3>, <.wma>, <.wav> or <.
R Unplayable discs • Unplayable disc types and formats are as follows: - DVD-Audio/DVD-ROM discs - MPEG4/DivX*/FLAC/MKV/DVD-VR/DVD+VR/ DVD-RAM recorded on DVD-R/RW or +R/+RW - SVCD (Super Video CD), CD-ROM, CD-I (CD-I Ready), DTS-CD - MPEG4/DivX*/FLAC/MKV recorded on CD-R/RW • Discs that are not round. Discs with coloring on the recording surface or discs that are dirty. • Recordable/Rewritable discs that have not been finalized. 3 inch discs.
- iPhone SC* iPhone 5* iPhone 45 iPhone 4 iPhone 3GS iPhone 3G iPhone 0 Language codes {for DVD language selection) * You cannot watch video when connecting Lightning connector models. • When operating an iPod/iPhone, some operations may not be performed correctly or as intended. In this case, visit the following JVC web site: • For some iPod/iPhone models, the performance may be abnormal or unstable during operation.
If an error occurs while using the unit, a message appears. Take appropriate action according to the following message/remedy/cause list. "No Signal"r'No Video Signal": • Start playback on the external component connected to the iPod/AV-IN input terminal. • Check the cords and connections. • Signal input is too weak. "Miswiring DC Offset Error" /"Warning DC Offset Error": • A speaker cord has shorted or it has come into contact with the car chassis.
11 Pandora not available": • You cannot use the Pandora application from the area where you are currently trying to access Pandora. 11 Try again later": • The Pandora server is under maintenance. 11 Station does not exist": • The selected station has been deleted by another device or has expired. 11 SXM Check Tuner": • Make sure the SiriusXM Connect Vehicle Tuner is connected to the unit.
CES ODiscs OUSB Recordable/Rewritable discs cannot be played back. • Insert a finalized disc. • Finalize the discs with the component which you used for recording. "Reading" does not disappear from the screen. • Turn the power off and on again. Tracks on the Recordable/Rewritable discs cannot be skipped. • Insert a finalized disc. • Finalize the discs with the component which you used for recording. Playback does not start. • The format of files is not supported by the unit.
No sound of videos comes out. • Connect with USB Audio and Video cable KS-U59 (optional accessory) to iPod/iPhone 30-pin connector model. Other cables cannot be used. • Select [USB+AV-IN] for . (Page 21) OTuner SSM automatic presetting does not work. • Store stations manually. (Page 27) Static noise while listening to the radio. • Connect the antenna firmly. DAV-IN 11 AV-IN" cannot be selected on the Home screen. • Select [USB 1 Wire] for .
REEE.RE s 0 DVD player section 0 USB interface section D/ A Converter 24 bit USB Standard Audio Decoder Linear PCM/Dolby Digitai!MP3/ WMA/WAV/AAC Compatible Device DivX*/MPEG1/MPEG2/JPEG Below Measurable Limit File System Video Decoder Wow & Flutter Frequency Response 96kHz Sampling: 20Hz to 22 000 Hz 48 kHz Sampling: 20 Hz to 22 000 Hz 44.1 kHz Sampling: 20 Hz to 20 000 Hz Total Harmonic Distortion 0.
0 FM tuner section - - -87.9 MHz to 107.9 MHz (200kHz) DAM tuner section OGeneral Frequency Range 530kHz to 1 700kHz (10kHz) 531 kHz to 1 611 kHz (9kHz) Operating Voltage ---------~--~w-~,.- Frequency Range 87.5 MHz to 108.0 MHz (SO kHz) Usable Sensitivity (S/N: 30 dB, 22.5 kHz) 7.2 dBf (0.63 'tJ.V/75 0) Quieting Sensitivity (S/N: 46 dB, 22.5 kHz) 15.2 dBf (1.58 'tJ.V/75 0) Frequency Response (±3.
OTrademarks and licenses • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • "DVD Logo" is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries. • The "AAC" logo is a trademark of Dolby Laboratories. • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
U.S.A. JVCKENWOOD USA Cor oration TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. NEED HELP ON HOW TO HOOK UP? NEED ASSISTANCE ON HOW TO OPERATE? NEED TO LOCATE A JVC SERVICE CENTER? LIKE TO PURCHASE ACCESSORIES? JVC IS HERE TO HELP! TOLL FREE: 1 {800)252-5722 http ://www.us.jvckenwood.com Remember to retain your Bill of Sale for Warranty Service.
CANADA .JVC JVCKENWOOD CANADA INC. Warranty applies only to PRO~C~~s~i~~~~Canada GARANTIE by JVCKENWOOD CANADA INC. La garantls' applique seulement aux PRODUITSdistrlbues au Canada par JVCKENWOODCANADA INC. JVCKENWOOD CANADA INC. (hereafter called "JVC") gives the following express warranty for each new JVC product distributed in Canada by JVC and sold by an authorized JVC dealer.
