VIDEO CASSETTE RECORDER ENGLISH CONTENTS HR-J347EM SAFETY FIRST 2 Safety Precautions ...................... 2 INSTALLING YOUR NEW RECORDER 3 Basic Connections ...................... 3 INITIAL SETTINGS 4 Auto Set Up ............................... 4 Video Channel Set ...................... 5 Select Language ......................... 6 Select Television System ............. 7 Clock Set .................................... 8 On-Screen Displays .................... 9 PLAYBACK 10 Basic Playback .....
EN SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION IMPORTANT n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel.
INSTALLING YOUR NEW RECORDER 1 2 Aerial terminal RF Cable (provided) AV-IN terminals AV Cable (not provided) 3 It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED. Basic Connections Back of TV EN TV Aerial Cable 3 CHECK CONTENTS Make sure the package contains all of the accessories listed in “Specifications” (Z pg. 34).
EN INITIAL SETTINGS When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Auto Set Up function sets the tuner channels automatically. You can refer to the front display panel and/or the on-screen display to perform this procedure. Auto Set Up Auto Channel Set 2 q 3 5/8 Before starting, make sure of the following: ● The TV aerial cable should be connected to the recorder.
EN The video recorder is designed to send picture and sound signals via the connected RF cable to your TV on UHF channel 36; if you want to change this Video Channel to another channel between 32 and 40, perform the following steps. Video Channel Set Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. Before starting, make sure of the following: ● The recorder's power should be off.
EN INITIAL SETTINGS (cont.) Select Language 1 Turn on the TV and select the VIDEO channel (or AV mode). 1 2 3 3 4 5 6 7/ 8 9 0 2 TURN ON THE RECORDER Press . ACCESS MAIN MENU SCREEN Press MENU twice. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK.
EN Select Television System 1 Turn on the TV and select the VIDEO channel (or AV mode). 2 3 1 2 7/ 8 9 4 2 3 ¶ 7 MENU 4 ¡ Press MENU twice. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK. MAIN MENU FUNCTION SET TUNER SET ACCESS TV SYSTEM SELECT SCREEN Press PUSH JOG %fi to place the pointer next to "TV SYSTEM SELECT", then press OK.
EN INITIAL SETTINGS (cont.) Preparation Clock Set Turn on the TV and select the VIDEO channel (or AV mode). 2 3 4 5 6 DATE+/– 7/ STOP+/– 1 8 2 9 0 1 3 4 2 TURN THE RECORDER ON Press . ACCESS MAIN MENU SCREEN Press MENU twice. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK.
EN You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. On-Screen Displays 1 Turn on the TV and select the VIDEO channel (or AV mode). 2 1 2 3 4 5 6 7/ 8 9 0 3 4 4 2 1 3 ¶ 7 ¡ TURN ON THE RECORDER Press . ACCESS MAIN MENU SCREEN Press MENU twice. ACCESS FUNCTION SET SCREEN Place the pointer next to "FUNCTION SET" by pressing PUSH JOG %fi, then press OK. ACCESS O.S.D. SCREEN Place the pointer next to "O.S.D.
EN PLAYBACK The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Basic Playback 1 Y PLA RE W 2 ST SY R U LO CO 1 2 3 4 5 6 7/ 8 9 3 5/8 STOP/EJECT EM q Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is point toward the recorder.
EN 11 Take advantage of special functions possible with the recorder’s controls or the remote control. Playback Features FF High-Speed Search PL AY 2 1 ACTIVATE HIGH-SPEED SEARCH During playback or still, press FF for forward highspeed search, or REW for reverse high-speed search. 3 To resume normal playback, press PLAY. 5/8 0 Still Picture/Frame-By-Frame Playback 1 4 2 TV PROG 1 3 ¶ 7 FF 8 4 PAUSE ¢ 2 ACTIVATE FRAME-BY-FRAME PLAYBACK Press PAUSE. OR Press PUSH JOG or .
EN PLAYBACK (cont.) Repeat Playback Manual Tracking Your video recorder can automatically play back the whole tape 20 times repeatedly. Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. 1 2 3 START PLAYBACK Press PLAY. ACTIVATE REPEAT PLAYBACK Press PLAY and hold for over 5 seconds, then release. ● The Play indicator ($) on the display panel blinks slowly.
EN Index Search Next Function Memory Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. £ 2 NOTE: ACTIVATE INDEX SEARCH fi % Press PUSH JOG or (™ or £) on the remote control. “™ 1” or “£ 1” is displayed on screen and search begins in the corresponding direction.
EN RECORDING TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. Basic Recording PLAY COLOUR SYSTEM Turn on the TV and select the VIDEO channel (or AV mode). 2 q 3 5/8 RE CO RD STOP/EJECT TV PROG 3 4 5 6 7/ 8 9 /L P 2 0 SP NUMBER 1 4 2 1 LOAD A CASSETTE Insert a cassette with the record safety tab intact.
EN 15 Record One Programme While Watching Another Recording Features If your recorder is connected to the TV via AV connection, . . . . . . press TV/VCR. The recorder's VCR indicator and the TV broadcast being recorded disappear. 1 2 5/8 Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.
EN TIMER RECORDING Timer Programming 1 Remember, the clock must be set before you can programme the timer (Z pg. 8). Before performing the following steps: ● Insert a cassette with the safety tab in place. The recorder will come on automatically. ● Turn on the TV and select the VIDEO channel (or AV mode). ● Select the appropriate colour system by pressing the COLOUR SYSTEM button.(Z pg.
EN 2 3 4 5 6 7/ 8 9 8 D AI LY 1 WEEKLY 0 4 TIMER 9 2 TV PROG 1 3 ¶ 7 RETURN TO NORMAL SCREEN After confirming all information is correct, press OK and the normal screen appears. ● Repeat steps 1–8 for each additional programme. ENGAGE RECORDER’S TIMER MODE Press TIMER. The recorder turns off automatically. ¡ To Timer-Record Weekly Or Daily Serials . . . . . .
EN TIMER RECORDING (cont.) Auto Timer When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automatically disengaged when the recorder is powered back on. 1 2 3 4 5 6 7/ 8 9 0 1 4 TIMER 2 1 3 ¶ 7 4 1 MENU 3 2 ¡ 8 ACCESS MAIN MENU SCREEN Press MENU twice. ACCESS FUNCTION SET SCREEN Press PUSH JOG %fi to place the pointer next to "FUNCTION SET", then press OK.
EN 19 Check And Cancel Programmes 1 2 3 4 5 6 7/ 8 9 0 PROG CHECK 1 CANCEL 4 2 TV PROG START+/– 3 ¡ D 1 STOP+/– 4 1 8 /– 7 E+ AT ¶ ¢ 3 2 ACCESS PROGRAMME DISPLAY AND/OR SCREEN Press PROG CHECK. ● If the recorder is turned on and the TV is set to its VIDEO channel or AV mode, you can check program information on screen. ● Each time you press PROG CHECK, the next programme's information appears. If All Information Is Correct . . . . . . programming is completed.
EN EDITING You can use your video recorder as the source player or the recording deck. Edit To Or From Another 1 Video Recorder 2 1 2 3 4 5 6 7/ 8 9 0 NUMBER "0" 3 4 4 Connect the player’s AUDIO/VIDEO OUT connector to the recorder’s AUDIO/VIDEO IN connector. SET RECORDING DECK’S INPUT MODE Set to AUX. With this video recorder, press NUMBER Key "0" or TV PROG. "AU" will appear instead of a channel number. START SOURCE PLAYER Engage its Play mode.
EN Edit From A Camcorder 1 2 3 4 5 6 7/ 8 9 0 You can use a camcorder as the source player and your video recorder as the recorder. 1 2 3 4 NUMBER "0"2 TV PROG 1 3 ¶ 7 4 1 3 ¡ 4 MAKE CONNECTIONS Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder’s AUDIO/VIDEO input connectors. SET RECORDER’S INPUT MODE Press NUMBER key "0" and/or TV PROG so that "AU" appears on the display panel. START CAMCORDER Engage its Play mode. START RECORDER Engage its Record mode.
EN INFORMATION ON MULTI-SYSTEM COMPATIBILITY Setting Of The Colour System Select Buttons Use the COLOUR SYSTEM button on the recorder's front panel to select the colour system. Pressing this button changes the mode as illustrated on the left. The On-Screen display will show which mode is selected. Mode AUTO Mode Display COLOUR SYSTEM NTSC PAL* AUTO (Colour Signal) Usually set to this mode.
EN 23 Playback This recorder can play back all 4 types of recorded tape. Recorded tape PAL HR-J347EM PAL receiver Built-in RFconverter G, K, I Playback circuit RF OUT PAL PAL NTSC NTSC[PAL SECAM receiver MESECAM SECAM MESECAM RF OUT SECAM Multi-system monitor SECAM VIDEO OUT AUDIO OUT PAL SECAM NOTES: When viewing NTSC tapes on a PAL TV set: ● The picture may shrink vertically with black bars appearing at the top and bottom of the screen.
EN TUNER SET Turn on the TV and select the VIDEO channel (or AV mode). 3 2 3 4 5 6 7/ 8 9 0 TV PROG ¶ 7 ¡ 4 SELECT AUTO CH SET MODE Press PUSH JOG%fi to place the pointer next to "AUTO CH SET", then press OK. 8 4 1 MENU 3 ¢ PUSH JOG SELECT TV SYSTEM Press PUSH JOG%fi to place the pointer next to the appropriate TV system, then press OK. ● Auto Channel Set will start.
EN Manual Channel Set Store channels that were not stored during Auto Set Up (Z pg. 4) or Auto Channel Set (Z pg. 24). 1 2 3 ACCESS TUNER SET SCREEN 6 Perform steps 1 – 3 of "Auto Channel Set" on page 24. ACCESS MANUAL CH SET SCREEN Press PUSH JOG %fi to place the pointer next to "MANUAL CH SET", then press OK. SELECT BAND Press PUSH JOG %fi to place the pointer next to the band of your choice, then press OK to initiate Manual Channel Set.
EN TUNER SET (cont.) Delete A Channel Example:To swap CH03 and CH09. Perform steps 1 – 3 of "Auto Channel Set" on page 24. ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK. SELECT CHANNEL Press PUSH JOG %fi to until the channel you want to delete begins blinking.
EN Fine-Tuning Channels 1 2 3 Perform steps 1 – 3 of "Auto Channel Set" on page 24. ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK. SELECT CHANNEL TO FINE-TUNE ● The "FRQ" number for that channel starts blinking. 4 5 TV System Selection – When you see the picture but hear no audio ACCESS TUNER SET SCREEN Press PUSH JOG %fi until the channel you want to tune begins blinking, then press OK twice.
EN TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is applied to the recorder. ● The mains power cord is disconnected. Connect the mains power cord. 2. The clock is functioning properly, but the recorder cannot be powered.
EN 29 2. TV broadcasts cannot be recorded. ● “AU” has been selected as the input mode. Set to the desired channel. 3. Tape-to-tape editing is not possible. ● The source (another video recorder, camcorder) has not been properly connected. ● All necessary power switches have not been turned on. ● The input mode is not correct. Confirm that the source is properly connected. ● The camcorder has not been properly connected. ● The input mode is not correct.
EN QUESTIONS AND ANSWERS PLAYBACK RECORDING Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen? A. This is normal. It reduces distortion at the pause and resume points.
INDEX EN 31 FRONT VIEW 1 2 3 4 5 2 3 POWER DISPLAY COLOUR SYSTEM AUTO SP/LP TIMER TV PROG REVIEW M q 5/8 INTELLIGENT PICTURE SPLPEP VCR 6 1 2 3 4 5 6 7 8 7 8 POWER Button Z pg. 4 Cassette Loading Slot Rewind [REW] Button Z pg. 10 PLAY Button Z pg. 10 Fast Forward [FF] Button Z pg. 10 AUTO SP/LP TIMER Button Z pg. 17 DISPLAY Button Z pg. 15 AUTO SP/LP TIMER Indicator Z pg. 17 0 9 9 0 ! @ # $ % ! @# $ % Display Panel Z pg. 32 Infrared Beam Receiving Window TV PROG 5/∞ Buttons Z pg.
EN INDEX (cont.) DISPLAY PANEL 1 2 3 4 5 REVIEW M SPLPEP VCR 6 7 8 1 Symbolic Mode Indicators PLAY: FF/REW VARIABLE SHUTTLE SEARCH: STILL: SLOW: RECORD: RECORD PAUSE: 2 "Timer" Indicator Z pg. 17 3 Counter Memory Indicator Z pg. 13 9 4 Channel*/Mode Display Z pg. 14 *Channel position 1 will be displayed as "CH 1". Clock Display Z pg. 8 5 Instant REVIEW Indicator Z pg. 13 6 "Cassette Loaded" Mark 7 VCR Indicator Z pg. 15 8 Tape Speed Indicators Z pg. 14 9 Counter Display Z pg.
EN 1 2 3 4 5 6 7 8 9 1 2 4 5/ADD TIME 6 7/ PROG CHECK ! @ # $ START 1 8/DAILY 9/WEEKLY CANCEL /C.RESET 0/AUX 4 TIMER STOP REW ¶ REC PROG 1 /MENU 3PLAY 7 STOP 4 TV PROG DATE FF ¡ 8 PAUSE TV VOL ¢ o 3 OK C.MEMORY % 3 EXPRESS PROGRAMMING 2 0 TV/VCR DISPLAY (MONITOR). TV ^ & * ( ) q w e r t y u i TV VOL PUSH JOG p Press and hold TV button while pressing , TV PROG. + / –, TV / VCR 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ^ & * ( ) q % % % w e r t y u i o DISPLAY Button Z pg.
EN SPECIFICATIONS GENERAL Power requirement Rating : Operating : Power consumption : Temperature Operating : Storage : Operating position : Dimensions (WxHxD) : Weight : Format : Maximum recording time (SP) : (LP) VIDEO/AUDIO Signal system Recording system Signal-to-noise ratio Horizontal resolution Frequency range Input/Output AC 110 – 240 V`, 50/60 Hz AC 090 – 260 V`, 50/60 Hz 18 W 5°C to 40°C –20°C to 60°C Horizontal only 400 x 94 x 273 mm 3.3 kg VHS standard 240 min.
