® ENGLISH CONTENTS SAFETY FIRST 2 Safety Precautions ...................... 2 INSTALLING YOUR NEW RECORDER 4 VIDEO CASSETTE RECORDER HR-S5700AM Basic Connections ..................... 4 S-VIDEO Connection ................. 5 INITIAL SETTINGS 6 Video Channel Set ..................... 6 Auto Set Up ............................... 8 On-Screen Displays ................. 10 Select Language ....................... 11 Clock Set .................................. 12 PLAYBACK 13 Basic Playback .........
EN SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel.
EN 3 POWER SYSTEM This set operates on voltage of AC110 – 240 V` (Rating), AC90 – 260 V` (Operating), 50/60 Hz with automatic switching. The STANDBY/ON current on and off. " button does not completely shut off mains power from the unit, but switches operating " shows electrical power standby and " " shows ON. Video tapes recorded with this video recorder in the LP (Long Play) or EP (Extended Play) mode cannot be played back on a single-speed video recorder.
EN INSTALLING YOUR NEW RECORDER Basic Connections Aerial terminal RF Cable (provided) Back of TV TV Aerial Cable It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED. 1 2 3 AV-IN terminals AV Cable (not provided) Mains Power Cord Rear View Mains outlet AUDIO OUT/ VIDEO OUT Connect the power plug to an AC outlet before installing the lithium battery. pg.
EN 5 S-VIDEO Connection Back of TV Aerial terminal S-Video cable (provided) S-VIDEO IN connector AUDIO IN connectors Aerial or Cable Audio cable (not provided) Mains outlet Mains Power Cord ANT. IN AUDIO OUT Back of Recorder S VIDEO OUT RF Cable (provided) ● To Connect to A TV With S-VIDEO/AUDIO IN Connectors . . . 1 2 CONNECT RECORDER TO TV a– Connect the aerial, recorder and TV as per "RF CONNECTION" ( pg. 4). b– Connect the recorder's S VIDEO OUT connector to the TV's S-VIDEO IN connector.
EN INITIAL SETTINGS Video Channel Set Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.
EN 3 SET VIDEO CHANNEL Set your TV to UHF channel 36. With AV Connection or S-VIDEO Connection ● If the two vertical white bars appear clearly on the screen as shown in the illustration ( "TEST SIGNAL" on page 6), press OK and then go to step 4. ● If the two vertical white bars do not appear clearly, press OK and then PR +/– to set the video recorder to a vacant channel between 28 and 60 which is not occupied by any local station in your area.
EN INITIAL SETTINGS (cont.) 1 2 1 2 3 4 5 6 7 8 9 2 3 4 0 1 4 3 OK MENU PUSH JOG SELECT LANGUAGE Press PUSH JOG %fi to place the pointer next to your desired language (English or Chinese), then press OK or PUSH JOG . fi ● Don't press any buttons on the recorder or remote that are not directly related to the step you are performing while Auto Set Up is in progress.
EN TV System Australia, New Zealand, Kuwait, U.A.E., Indonesia, Singapore, Thailand, Malaysia, Iran, Saudi Arabia, Egypt, Morocco, Lebanon, Iraq B/G China, Mongolia, Russia D/K Hong Kong I U.S.A., Japan, S.Korea, Taiwan M 0 5 6 SELECT TV SYSTEM Press PUSH JOG %fi to place the pointer next to the appropriate TV system (refer to the table on the left). START AUTO CHANNEL SET Press OK or PUSH JOG .
EN You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. 1 Turn on the TV and select the VIDEO channel (or AV mode). 2 1 2 3 4 5 6 7 8 9 3 2 4 0 4 1 Press . ACCESS MAIN MENU SCREEN Press MENU. ACCESS FUNCTION SET SCREEN Place the pointer next to "FUNCTION SET" by pressing PUSH JOG %fi, then press OK or PUSH JOG .
EN Select Language 1 Turn on the TV and select the VIDEO channel (or AV mode). 1 2 2 5 6 7 8 9 TURN ON THE RECORDER Press . ACCESS MAIN MENU SCREEN Press MENU. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . % 3 3 4 2 11 MAIN MENU FUNCTION SET TUNER SET INITIAL SET [5/∞ ] = [MENU] : EXIT 4 0 3 MENU Press PUSH JOG %fi to place the pointer next to "LANGUAGE", then press OK or PUSH JOG .
EN INITIAL SETTINGS (cont.) Clock Set Turn on the TV and select the VIDEO channel (or AV mode). 1 2 1 2 3 4 5 6 2 7 8 4 Press . ACCESS MAIN MENU SCREEN Press MENU. ACCESS INITIAL SET SCREEN Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . % 3 9 TURN ON THE RECORDER 0 MAIN MENU FUNCTION SET TUNER SET INITIAL SET [5/∞] = [MENU] : EXIT 1 OK 4 Press PUSH JOG %fi to place the pointer next to "CLOCK SET", then press OK or PUSH JOG .
PLAYBACK EN The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. S-VHS playback is possible only with S-VHS PAL tapes recorded in SP or LP, or S-VHS NTSC tapes recorded in the SP or EP mode.
EN PLAYBACK (cont.) NOTE: e rs la Re p ve Refer to the SHUTTLE ring illustration to the right as you read the following procedures. v e rs e Re low s Slow motio n y Pl a y Playback Features Still search Reverse sea ard Forw rch G JO PLAY PR+ PR +/ – ST O P SHUTTLE PAUSE PR– PR +/– Still Picture/Frame-By-Frame Playback 1 AY PL 1 FF REW PAUSE STOP 3 2 PAUSE DURING PLAYBACK Press PAUSE. If there is vertical jitter, use the PR +/– buttons to correct the picture.
EN Variable-Speed Search 1 Manual Tracking ACTIVATE VARIABLE-SPEED SEARCH Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the PR +/– buttons. During playback or still, turn the SHUTTLE ring to the right for forward variable-speed search, or to the left for reverse variable-speed search (refer to the illustration on page 14). or % % OR During playback, press PUSH JOG .
EN PLAYBACK (cont.) Next Function Memory Skip Search The Next Function Memory "tells" the recorder what to do after rewinding. Before continuing, ensure that the recorder is in the Stop mode. a– For Automatic Start Of Playback After Tape Rewind... ...press REW, then press PLAY within 2 seconds. b– For Automatic Power Off After Tape Rewind... ...press REW, then press within 2 seconds. c– For Automatic Timer Standby After Tape Rewind... ...press REW, then press ‰ within 2 seconds.
RECORDING EN TV signals being received by the recorder's built-in tuner can be recorded onto a video tape. You can "capture" a TV programme using your video recorder. S-VHS recording is possible only for PAL recordings made in the SP or LP mode, or NTSC recordings made in the SP mode. S-VHS ET recording is possible only for PAL recordings made in the SP mode, or NTSC recordings made in the SP mode.
EN RECORDING (cont.) Record One Programme While Watching Another Recording Features 1 SELECT CHANNEL TO WATCH Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view. ● The programme selected with the TV's channel controls appears on the TV screen while the one selected with the PR +/– buttons is recorded on the tape. PR+ Elapsed Recording Time Indication You can check the exact time of a recording.
EN Instant Timer Recording (ITR) This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished. 1 2 3 START RECORDING Press RECORD on the recorder. ENGAGE ITR MODE Press RECORD again. " " blinks and 0:30 appears on the front display panel. SET RECORDING DURATION If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.
EN RECORDING (cont.) S-VHS ET S-VHS (Super VHS), S-VHS ET and VHS PR+ PR– 4 0 1 3 MENU OK PUSH JOG Your recorder can record in S-VHS, S-VHS ET or VHS. S-VHS allows you to make high quality video recordings with a horizontal resolution of 400 lines. This compares with the 240 lines of resolution of normal VHS recordings. To achieve the highest quality picture we recommend that you record in S-VHS mode.
EN 21 S-VHS ET Super VHS ET PR+ PR– Your recorder is equipped with Super VHS ET that makes it possible to record with S-VHS picture quality on VHS cassettes. 1 SELECT S-VHS ET SET MODE Press S-VHS ET. The button lights up. ● The "S-VHS" indicator lights on the front display panel. ● To disengage the S-VHS ET mode, press S-VHS ET. The button's light goes off. NOTES: ● You cannot activate the S-VHS ET function... ...while recording is in progress. ...while timer-recording (incl.
EN RECORDING (cont.) B.E.S.T. Picture System PLAY Turn on the TV and select the VIDEO channel (or AV mode). The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is "ON". Preparation 1 2 PR+ RE CO RD PR– Press . ACCESS MAIN MENU SCREEN Press MENU.
EN Recording 1 START RECORDING Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE Playback The recorder assesses the quality of the tape once you initiate playback. 1 START PLAYBACK Press PLAY. ● The recorder adjusts the playback picture quality based on the quality of the tape in use. ● B.E.S.T. is active during Auto Tracking. "BEST" appears blinking on the recorder's display panel.
EN TIMER RECORDING G-CODE™/SHOWVIEW™ System Setup Turn on the TV and select the VIDEO channel (or AV mode). The G-CODE timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the G-CODE number for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed.
EN 1 2 5 3 NUMBER 2 5 6 7 8 9 Press PUSH JOG %fi or NUMBER keys to input the number of the recorder's channel position on which the Guide Program number's broadcast is received. Then press OK or PUSH JOG . G-CODE/SHOWVIEW SETUP GUIDE PROG TV PROG 2 2 [0-9] OR [5/∞]:SELECT = [MENU] : EXIT ● If the satellite broadcast is received on your recorder's auxiliary channel "L-1", select "L-1" for the channel position. ● Repeat steps 4 and 5 as necessary.
EN TIMER RECORDING (cont.) With the G-CODE system , timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. G-CODE™/SHOWVIEW™ Timer Programming 1 ACCESS G-CODE/ SHOWVIEW SCREEN Press PROG. G-CODE/SHOWVIEW [0 – 9] = [+/–] : EXPRESS PROGRAMING [PROG] : EXIT Remember, the clock must be set before you can programme the timer ( pg. 10).
EN NUMBER 1 2 D AI LY 5 4 5 6 7 8 9 3 2 WEEKLY 4 0 STOP+/– RETURN TO NORMAL SCREEN Press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ● Repeat steps 1 – 5 for each additional programme. ENGAGE RECORDER'S TIMER MODE Press ‰. The recorder turns off automatically and "‰" appears on the display panel. ● To disengage the timer, press ‰ again.
EN TIMER RECORDING (cont.) Express Timer 1 Programming Remember, the clock must be set before you can programme the timer ( pg. 12). 2 Before performing the following steps: ● Insert a cassette with the safety tab in place. The recorder will come on automatically. ● Turn on the TV and select the VIDEO channel (or AV mode). ● Select the appropriate colour system by pressing the COLOUR SYSTEM button ( pg. 44). ACCESS G-CODE SCREEN Press PROG. ACCESS PROGRAMME SCREEN Press START +/–.
EN 1 D AI LY 7 2 3 4 5 6 7 8 9 2 WEEKLY 8 SP/LP/EP PROG 3 SET TAPE SPEED Press SP/LP/EP ( ) to set the tape speed. RETURN TO NORMAL SCREEN After confirming all information is correct, press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ● Repeat steps 1 – 8 for each additional programme. 4 0 1 29 OK 9 ENGAGE RECORDER'S TIMER MODE Press ‰. The recorder turns off automatically and "‰" appears on the display panel.
EN TIMER RECORDING (cont.) Check, Cancel And Replace Programmes 1 2 3 4 5 6 1 8 DATE+/– 7 STOP+/– 2 9 4 0 PR +/– START+/– 2 DISENGAGE TIMER MODE Press ‰, then press . ACCESS PROGRAMME CHECK SCREEN Press ‰?. SP/LP/EP 1 3 OK MENU PUSH JOG 3 PR START STOP 1 8:00 10:00 2 10:00 10:45 3 11:30 13:00 4 5 6 7 8 ‰?] : NEXT [‰ CH 3 2 1 DATE 24.12 25.12 25.12 ACCESS PROGRAMME SCREEN Press ‰? again to check more information.
EN 31 When programmes overlap each other If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. The Programme Check screen appears and conflicting programmes will start blinking. 1 2 3 5 6 8 9 PROGRAM OVERLAPPED 7 STOP+/– 2 4 4 PR +/– 0 PR START 1 8:00 2 10:00 3 11:30 4 9:00 5 6 7 8 [5/∞] = STOP 10:00 10:45 13:00 10:00 CH 3 2 1 92 DATE 24.04 25.04 25.
EN TIMER RECORDING (cont.) Auto SP→LP Timer Auto Timer If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode (with PAL broadcasts) or EP mode (with NTSC broadcasts) to allow complete recording. For Example . . . Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape.
EN Automatic Satellite Program Recording This facility allows you to automatically record a satellite program which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder's rear AUDIO/VIDEO IN connectors and program the timer on the satellite receiver; the recorder starts recording when the signals input from the satellite receiver to the rear AUDIO/VIDEO IN connectors, and when there is no input signals the recorder stops recording and the power shuts off.
EN SPECIAL FEATURES Remote A/B Code Switching Remote Control Functions The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control's A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.
EN TV CA BL E/ SA T/ D VD TV Multi-brand Remote Control Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer's TVs can also be controlled. Before you start . . . ● Turn on the TV using its remote control. VCR TV/VCR 1 2 3 4 5 6 7 8 9 2 35 NUMBER 4 1 0 SET TV BRAND CODE Refer to the chart below. While holding down TV on the recorder's remote control, enter your TV's brand code using the NUMBER keys, then press OK.
EN SPECIAL FEATURES (cont.) TV CA BL E/ SA T/ D VD Multi-brand Remote Control For satellite receiver, cable box and DVD Your remote control can operate the basic functions of your satellite receiver , cable box or DVD. Before you start . . . ● Turn on the satellite receiver, cable box or DVD using its remote control. VCR 1 2 3 4 5 6 7 8 9 2 NUMBER 4 0 1 AY PL FF STOP 3 TV PR+/– OK @ # +/– Refer to the chart below.
EN Cable Box or Satellite Receiver Multi-brand Code CABLE BOX BRAND NAME JVC AMSTRAD BT CANAL+ CANAL SATELLITE D-box ECHOSTAR FINLUX GALAXIS GRUNDIG HIRSCHMANN ITT JERROLD KATHREIN LUXOR MASPRO NOKIA PACE PANASONIC PFT PHILIPS PHONOTREND SALORA SKYMASTER TPS VIDEOWAY WISI CODE 72, 73, 60, 61, 62, 63, 92 72 81 81 85 51, 78, 79, 80, 82 68 69, 88 64, 65 64 68 01, 04, 06, 11, 12, 15, 28, 75 70, 71 68 70 68, 87 67, 86, 92 13, 14, 74 69 66, 84 69 68 69 83 03, 09, 22, 76, 77 64 DVD Multi-brand Code DVD BRAND NA
EN SYSTEM CONNECTIONS Connecting/ Using A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
EDITING EN Turn on the TV and select the VIDEO channel (or AV mode). Picture Control This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO." 1 2 1 2 3 4 5 6 7 8 9 2 3 4 Press MENU. ACCESS FUNCTION SET SCREEN Place the pointer next to "FUNCTION SET" by pressing PUSH JOG %fi, then press OK or PUSH JOG . SELECT PICTURE CONTROL SET MODE Place the pointer next to FUNCTION SET "PICTURE CONTROL" by B. E. S. T.
EN EDITING (cont.) Edit From A Camcorder 1 2 3 4 5 6 7 8 9 You can use a camcorder as the source player and your video recorder as the recorder. MAKE CONNECTIONS 1 A If the camcorder has no S-VIDEO output connector... ... connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's front panel AUDIO/ VIDEO input connectors. B If the camcorder has an S-VIDEO output connector... ...
EN 41 You can use your video recorder as the source player or the recording deck. Edit To Or From Another 1 Video Recorder 2 Player TV Receiver Your recorder VIDEO CHANNEL AV Cable (not provided) RF Cable (provided) Another recorder Recorder Recorder Your recorder TV Receiver (MONO) VIDEO CHANNEL AV Cable (not provided) RF Cable (provided) Another recorder Player 3 4 5 MAKE CONNECTIONS Connect the player's AUDIO/VIDEO OUT connector to the recorder's AUDIO/VIDEO IN connector.
EN EDITING (cont.) Normal audio track Pre-recorded tape +/ – PLAY Audio Dubbing Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. PR Video/Hi-Fi audio track PR+ Audio-dubbed tape PR– PA U SE B U D A. CD Player etc. 2 3 4 CD Player etc.
PLAY EN 5 PR+ PA U SE PR– 6 START DUBBING Engage the audio component's Play mode, then press PLAY to start the tape in your recorder. Audio dubbing begins at this point. ● " " blinks and " " is displayed on the front display panel. ● To stop dubbing temporarily, press PAUSE. Press PLAY to resume dubbing. END AUDIO DUBBING Press STOP to stop the tape in your recorder, and engage the audio component's Stop mode.
EN INFORMATION ON MULTI-SYSTEM COMPATIBILITY Setting Of The Colour System Select Buttons Mode Display AUTO COLOUR SYSTEM Use the COLOUR SYSTEM button on the front panel to select the colour system. Pressing the COLOUR SYSTEM for about 2 seconds displays the current setting on the screen. While the current setting is displayed, press COLOUR SYSTEM again to change the mode as illustrated on the left. The On-Screen display will show which mode is selected. Mode NTSC 3.
EN 45 Playback This recorder can play back all 3 types of recorded tape. HR-S5700AM Recorded tape PAL Playback circuit Multi-system receiver PAL MESECAM Built-in RFconverter K, I, G, M, H MESECAM NTSC[PAL NTSC PAL (B/G, D/K, I, H) NTSC (M) RF OUT NTSC 3.58 MHz Multi-system monitor Manual switching Manual switching NTSC 4.43 MHz VIDEO OUT AUDIO OUT PAL SECAM NTSC 3.58 NTSC 4.
EN TUNER SET Turn on the TV and select the VIDEO channel (or AV mode). IMPORTANT Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( pg. 8) or if you have moved to a different area or if a new station starts broadcasting in your area. 3 4 5 6 7 8 9 Auto Channel Set 2 4 0 PR +/– 1 1 3 MENU OK 2 PUSH JOG 3 TURN ON THE RECORDER Press . ACCESS MAIN MENU SCREEN Press MENU.
EN AUTO CH SET PLEASE WAIT START 6 FINISH [5/∞] = [MENU] : EXIT CH FRQ SYS CH 01 150 BG 07 02 165 BG 08 03 195 BG 09 04 205 BG 10 05 213 BG 11 06 221 BG 12 [5/∞] = [ ] : DELETE : EDIT [5/∞] = [MENU] : EXIT FRQ 229 237 355 365 374 384 SYS BG BG BG BG BG BG RETURN TO NORMAL SCREEN Press MENU. NOTE: If you perform Auto Channel Set when the aerial cable is not connected properly, "SCAN COMPLETED -NO SIGNAL-" appears on the screen in step 5.
EN TUNER SET (cont.) Delete A Channel Example:To swap CH03 and CH09. ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL FRQ 229 237 355 365 374 384 SYS BG BG BG BG BG BG ● To re-store it, simply press PUSH JOG . ● Repeat steps 3 – 4 as necessary.
EN 3 ACCESS CHANNEL LIST Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL TO FINE-TUNE Press PUSH JOG %fi until the channel you want to tune begins blinking, then press OK twice. ● The "FRQ" number for that channel starts blinking. 5 FRQ 229 237 355 365 374 384 SYS BG BG BG BG BG BG Press PUSH JOG %fi until the picture becomes clearer, then press OK or PUSH JOG . ● Repeat steps 3 and 4 as necessary.
EN TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is applied to the recorder. ● The mains power cord is disconnected. Connect the mains power cord. 2. The clock is functioning properly, but the recorder cannot be powered.
EN 51 RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Recording cannot be started. ● There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed. Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. 2. TV broadcasts cannot be recorded. ● "L-1", "F-1", "S-1" or "S-2" has been selected as the input mode. Set to the desired channel. 3. Tape-to-tape editing is not possible.
EN TROUBLESHOOTING (cont.) OTHER PROBLEMS SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Whistling or howling is heard from the TV during camcorder recording. ● The camcorder's microphone is too close to the TV. ● The TV's volume is too high. Position the camcorder so its microphone is away from the TV. Turn the TV's volume down. 2. When scanning channels, some of them are skipped over. ● Those channels have been designated to be skipped. If you need the skipped channels, restore them. ( pg.
QUESTIONS AND ANSWERS EN 53 PLAYBACK TIMER RECORDING Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. " " and "‰" remain lit on the display panel. Is there a problem? A. No. This is a normal condition for a timer recording in progress. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Q. Can the video recorder indefinitely remain in the still mode? A. No.
EN INDEX FRONT VIEW COLOUR SYSTEM RE-VIEW STANDBY/ON S-VHS ET S-VIDEO(S-2) VIDEO(MONO) L–AUDIO–R PR+ REC LINK PR– +8 4 0 6 15dB NORM 1 STANDBY/ON Button pg. 10 2 COLOUR SYSTEM Button pg. 44 3 REVIEW Button pg. 16 4 Cassette Loading Slot 5 PLAY Button pg. 13 6 JOG Dial pg. 14 7 SHUTTLE Ring pg. 14 8 S-VIDEO(S-2)/VIDEO/AUDIO Input Connectors pg. 40 9 PR +/– Buttons pg. 17 VN LD REVIEW SP S VPS/PDC VCR SP/LP/EP A.DUB 0 REC LINK Button pg. 17 ! S-VHS ET Button pg.
EN REAR VIEW OUT IN(S-1) VIDEO (MONO) S VIDEO L ANT. IN AUDIO R OUT IN RF OUT PAUSE 1 Mains Power Cord pg. 4, 5 2 AUDIO/VIDEO OUT Connectors pg. 4, 5, 41 3 AUDIO/VIDEO IN Connectors pg. 41 4 S VIDEO OUT Connector pg. 5 5 S VIDEO IN(S-1) Connector pg. 40 6 ANT. IN Connector pg. 4, 5 7 Remote PAUSE Connector pg. 40 8 Lithium Battery Compartment pg. 7 9 RF OUT Connector pg. 4, 5 DISPLAY PANEL +8 4 0 6 SP REVIEW 15dB NORM 1 B.E.S.T. Picture System Display pg.
EN INDEX (cont.) REMOTE CONTROL VCR TV CABLE/ SAT/DVD TV/VCR AUDIO 1 2 3 4 5 6 VPS/PDC DAILY/QTDN. WEEKLY/HEBDO 7 8 9 0000 AUX 2 4 0 STOP FIN START DEBUT DATE PR EXPRESS 1 PROG 30 SEC MENU ENTER/ ENTR EE TV PR + 3 O K + TV 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ^ TV – TV PR – & * ( ) q w e r t y u i o p Q W E Buttons with a small dot on the left side of the name can also be used to operate your TV pg. 35. % % 1 TV Button pg. 35 2 VCR Button pg.
SPECIFICATIONS GENERAL Power requirement Rating : Operating : Power consumption : Temperature Operating : Storage : Operating position : Dimensions (WxHxD) : Weight : Format : Maximum recording time (SP) : (LP) (EP) VIDEO/AUDIO Signal system Recording system Signal-to-noise ratio Horizontal resolution Frequency range Input/Output AC 110 – 240 V`, 50/60 Hz AC 090 – 260 V`, 50/60 Hz 22 W 5°C to 40°C –20°C to 60°C Horizontal only 400 x 94 x 347 mm 4.2 kg S-VHS/VHS standard 240 min.
MEMO
MEMO
EN HR-S5700AM ® VICTOR COMPANY OF JAPAN, LIMITED ® Registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.
