ENGLISH LT-20DA6SK INTEGRATED DIGITAL WIDE LCD PANEL TV INSTRUCTIONS D Digital Video Broadcasting Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) Number: 3795
Contents i For your safety ........................................ 2 Other Features ...................................... 33 Important Instruction ............................. 4 PC Mode ................................................ 35 Where to install ...................................... 5 Remote Control Buttons ......................... 9 Installation .......................................... 35 Main Menu in PC mode: ..................... 35 PC Picture Position Menu: .................
For your safety This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety. They are of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have just purchased.
table-cloths, curtains etc. Overheating will cause damage and shorten the life of the equipment. DONT allow electrical equipment to be exposed to dripping or splashing or objects filled with liquids, such as vases, to be placed on the equipment. DONT place hot objects or naked flame sources, such as lighted candles or night-lights on, or close to the equipment. High temperatures can melt plastic and lead to fires. DONT use makeshift stands and NEVER fix legs with wood screws.
WARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down. Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV. Doing so may cause the TV to fall over and lead to injuries.
Where to install WARNING When you install the TV on the wall, only use a JVC wall mounting unit which is designed for this TV. Make sure the TV is installed on the wall by a skilled installer. Locate the TV away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing.
Important Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused by: fire; earthquake; accidental damage; intentional misuse of the product; use of the product in improper conditions; loss and/or damage caused to the product whilst in the possession of a third party; any damage or loss caused as a result of the owner s failure and/or neglect to follow the instructions set out in the owners manual; any loss or da
Control Panel Buttons 32:(5 /$03 ,1)5$5(' 5(&(,9(5 63($.(5 63($.(5 79 $9 79 $9 0(18 2. 0(18 2. 352*5$0 92/80( 67$1' %< With certain combinations of connectors and leads the back cover may not be easily fitted. If the cover is left off, this in no way infringes safety requirements. -7ENG-20710W-17MB16P-1895UK-(LT-20DA6SK)-50076128.p65 7 18.10.
Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen 10° backward and 5° forward. Tilt the TV up and down: While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down. -8ENG-20710W-17MB16P-1895UK-(LT-20DA6SK)-50076128.p65 8 18.10.
Remote Control Buttons / I = (Stand By) button TV / VCR / DVD Switch '9 ' Number buttons 79 AV button (EXT-1, EXT-2, EXT-2S, EXT-3, EXT-4, EXT-4S, PC, DIGITAL TV) 5& 9 Colour button MENU = Menu button = Cursor Up button OK button $9 = Cursor Right button BACK = Back button = Volume - /+ buttons GUIDE button SUBTITLE button 0(18 79 '79 ZOOM = Zoom button buttons 2. %$&.
Features It is a remote controlled Integrated Digital colour television and PC monitor. 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system. It has 2 pieces of Euroconnector socket for external devices (such as video, video games, audio set, etc.) S-Video and AV inputs are available. Optional stereo sound systems (German or German+Nicam) are available. Multilanguage OSD.
Getting Started Follow Step 1 to 7 to set up your TV: Step 1: Checking the accessories supplied Remote control unit x 1 AA/R6 battery x 2 AC adapter x 1 Power cord x 1 Step 2: Inserting batteries Remove the battery cover located on the back of the remote control by gently pulling upwards from the indicated part. Insert two AA/R6 dry cell or equivalent type of batteries inside. Replace the battery cover.
FDUG VRFNHW WHUPLQDOV 100 mm mount based on VESA regulation is equipped. The handle and the stand can be left by loosing the screws with a screwdriver when mounting the TV on a wall. Spread a soft cloth on a flat table and then place the TV on the cloth with the screen facing downwards when you leave the handle and the stand. Step 4: Connecting an aerial VCR and mains Please read the user manual of each device before connecting, to ensure a correct setup.
&RQQHFW D YLGHR GHYLFH $(5,$/ (;7 (;7 $& DGDSWHU 7R '& ,1 9&5 IMPORTANT: Only use the adaptor supplied with this TV. The TV set is designed to operate on 24 V DC. For this, an adaptor is used which gives 24 V DC voltage. Connect this adaptor to a system that supplies 100-240 V AC, 50 Hz. Step 5: Using the cable holder A cable holder which is used to keep the connection cables tidy is supplied.
Step 6: Switching the TV ON/OFF To switch the TV on 35 /LVW (PSW\ 6WDUW DXWRPDWLF VHDUFK Your TV will switch on by two steps: 1- Connect the power supply cord to the system. Then the TV switches itself to standby mode and the power lamp becomes red located on the front of the TV. 2- To switch on the TV from stand-by mode either: Press the , button on the remote control or on the right side of the TV or.
First of all choose the Language which the menus of the analogue part of the TV will appear. As soon as you change the language, the menu items will be displayed in the selected language. By pressing the or button, come to the Country item and select the country. This will affect the sort process in APS. Press RED button to start A.P.S. After APS is finalized, a programme list will appear on the screen.
When you press the following buttons ( , TV / DTV, ZOOM, , / I, , AV, MENU, , BACK, / , SUBTITLE, GUIDE, number buttons) during recording, a message appears asking if you want to stop recording or not. Press OK button to stop recording or BLUE button to continue recording. Do not turn the TV off in the following cases: When recording images from an external device connected to TV (For example camcorder). When recording a TV channel after it has been unscrambled on a decoder.
Example: PR6 and 2. press 6, PR12 press 1 Press directly the programme number to reselect single digit programmes. Hint: The channel list numbers are assigned by the broadcasters. Because not all channels are broadcast free-to-air and stored by the receiver, the channel list numbers do not run continuously. The fifteenth channel in the list, for example, may not be channel number 15 but channel number 17.
Choosing Channel 1. Press or the channel. ELECTRONIC PROGRAMME GUIDE (EPG) Another way of selecting a channel is with the electronic programme guide, or EPG. Like the Channel List, the EPG screen displays a list of the stored channels along with information on what programmes are being broadcast. Using the Electronic Programme Guide EPG can display 7 days programme guide, but in some areas only current and next programme guide is displayed. buttons to choose 2. Press OK button.
DISPLAYING THE SUBTITLES With Digital terrestrial broadcasting (DVB-T), some programmes are broadcast with subtitles. Subtitles can be displayed when watching these programmes. Press the SUBTITLE button when watching Digital terrestrial broadcasting (DVB-T). Subtitle ON appears at the top-left of the screen and, if programme has subtitles, the subtitles are displayed. When the SUBTITLE button is pressed again, Subtitle OFF appears and the subtitles disappear.
from the TV to the VCR to automatically start and end the recording. It is not necessary to set the timer on the VCR. 7+5(( When your VCR is not T-V LINK compatible, you also need to set the VCR timer settings to match the TV timer settings. The recording may not start and stop at exactly the right times for some programmes. It is recommended that you allow some leeway when setting the recording times.
Mode: cording before you record the programme. There are some T-V LINK compatible recording device that will not correctly receive the Direct Rec command from the TV. Use the / buttons to choose the timer mode (Once/Daily/Weekly), and then press the OK button. If the recording device does not operate when the recording start time is reached, it means VCR is not receiving the Direct Rec command from the TV. In this case, follow the instructions of When recording on a T-V LINK incompatible VCR:.
Configuration Set the basic setting when watching Digital terrestrial broadcasting (DVB-T). 1. Press the Subtitle. / buttons and choose Choose configuration and press the OK button. 2. Press the / buttons and choose a subtitle language that appears when the SUBTITLE button is pressed. CONFIGURATION appears. Favourite Mode e Enable/disable the Edit PR List Favourites settings. f 1. Press the / Favourite Mode. buttons and choose / buttons and choose 2.
1. Press the / buttons and choose Enter PIN code, and press the OK button. 2. Input the current PIN code. When you are making this setting for the first time, input 0000. When a PIN code has already been set, enter the correct PIN code. $XWRP DWLF ' RZ QOR DG (QDEOHG The PIN code setting window appears. 6HDUFK IRU 1H Z 9HUVLRQ 3. Press the number buttons to input a new PIN code (password). The actual version may be different to the Receiver Upgrade version displayed above. 2.
Sometimes you may notice a drop in picture quality while watching your programme in the quarter-screen. This is not a fault. When the BACK button is pressed, the previous screen is returned to. When the TV/DTV or MENU button is pressed, the menu disappears. When the (information) button is pressed, the help screen appears. When it is pressed again, the previous screen is returned to. Here, you can preview any channel stored by the receiver before viewing it full screen.
Setting the favourite channels If only channels that you often watch are set as favourite channels, you can choose from / just those channels by pressing . After setting the favourite channels, check the Favourite Mode in Configuration (see page 22) is set to ON. 1. Press the / buttons and choose Favourites on the bar at the bottom of the screen. 2. Press the / buttons and choose the channel to be registered as a favourite channel, and then press the OK button.
When OK button is pressed, following message will appear on the right bottom side of the screen: warning screen is displayed in case of accidental operation. $UH \RX VXUH \RX ZDQW WR GHOHWH WKH 35 OLVW DQG UHVHW DOO VHWWLQJV" 35 /LVW (PSW\ Manual Search: This is for searching for digital channels on a single broadcast frequency.
To see the viewing contract information, press MENU, Select DIGITAL and Press OK, then Select Common Interface and press OK. Press MENU button again to remove menu. Picture Menu When no module is inserted, No CI Module appears. Press MENU button, now you are in main menu. In the Main menu, select Picture using or button, then enter the Pic- Refer to the module instruction manual for details of the settings. ture menu by pressing / or OK button.
Setting Sharpness Setting Colour Temp. Using or button select Sharpness. Press level. button to increase sharpness Press level. button to decrease sharpness or Using Temp. button select Colour Press or button to select Warm, Cool or Normal. Setting Noise Reduction Using or duction. button select Noise Re- Press or button to select Noise Reduction level Off or Minimum or Medium or Maximum.
Reset Setting Balance Press BLUE button to reset the picture modes to factory default settings. It allows adjusting the distribution between the left and right speakers. To Store the Settings Using or In the Picture Menu, all settings are stored automatically. Press ward. button to change balance right- Sound Menu Press ward. button to change balance left- As you enter the main menu, sound will be the second item.
Selecting Sound Mode or Using Mode. Press Mode. or Using or button select Child Lock. button select Sound Press / button to select Child Lock On or Off . button to change Sound The Child Lock feature can be set On or Off You can choose Mono, Stereo or Dual (I-II) mode, only if the selected channel supports that mode. In case of bilingual broadcast (Dual Sound), you can select original or dubbed language using mode option.
Selecting Fine Tuning You can use the Fine Tuning process for fine adjustment (after coarse adjustment), if you are not happy about the image on the screen. Use or button on Fine Tuning item, until getting the best image on the screen. Selecting Search In EXT mode, Install menu appears like this: To start the search process, press button for forward search or button for backward search.
After stored, T-V LINK menu will appear. If you do not need to do T-V LINK, select Cancel and press menu. or OK button to exit the Program Menu If you do not have a T-V LINK compatible VCR, Press "MENU" button, now you are in main menu. In the main menu, select Program using or button. Then enter the To give a channel name (Name): select Cancel and press or OK button to exit the menu. Programme menu by pressing / or OK button. 1.
automatically on your TV, according to the transmission of programme systems in your area. First of all choose the Country by using or button. Then press the Red button to start Autostore. After Autostore is finalized, a programme list will appear on the screen. In the program list you will see the programme numbers and names assigned to the programmes. If you do not accept the locations and/or the programme names of programmes, you can change them in Programme menu.
this volume is set to the preceding value, and the second one is increasing or decreasing the volume level. No-Signal Detection (TV mode) If no valid signal detected, it takes 5 minutes to switch to the Stand-By mode unless any signal detected or any Remote Control command is accessed. After a Remote Control command (if No-Signal Timer is active) the timer stops and if no signal detected again the timer is initialized to 5 minutes and starts 3 seconds later again to count down.
PC Mode Installation The top and bottom of the picture are slightly cut off. 14:9 ZOOM: This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen. Power off both Computer and the TV before making any connections. Set your PCs resolution correctly before connecting to the TV. See the table in page 43 for supported modes. Use a D-SUB cable to connect the TVs PC input to the computers RGB output terminal.
Auto Position If you shift the picture horizontally or vertically to an unwanted position, use this item to put the picture into correct place automatically. Select Auto position item by using buttons. or Press OK button. Press MENU button or BACK button to store the value. Warning: Auto position adjustment recommended to be done with the full screen image for the proper adjustment.
Contrast, Bright-1, Colour and Sharpness are described at Picture menu on page 27. Setting PIP Size or Using button select PIP Size. Press or button to change PIP size. Two different PIP sizes are available. Setting PIP Position or Using tion. button select PIP Posi- Press or button to change PIP position. There are four different PIP positions. Programme in the PIP window can be changed by / , digit buttons or AV button.
To select a page of Teletext Press the appropriate digit buttons for the required Teletext page number. The selected page number is displayed at the top left corner of the screen. The Teletext page counter searches until the selected page number is located, so that the desired page is displayed on the screen. button to move the Teletext Press screen forward one page at a time. Pressing button again will conceal the revealed answers.
nect the decoder to the VCR. If not, the T-V LINK function may not work properly. And then set the Decoder (EXT-2) function for the channel to ON to unscramble a scrambled channel. For Fastext and Toptext The subject-heading for the information may have a particular colour. Press an appropriate RED, GREEN, YELLOW or BLUE button in order to reach the relevant page quickly. For TOPTEXT If Toptext transmission is present, colour coded buttons will appear in status row.
supply you a corresponding decoder unit to allow the programmes to be unscrambled. For further information ask your dealer. See also the booklet supplied with your decoder. Connect a decoder with an aerial socket to the TV Connect the decoder to the video recorder Some video recorders have a special euroconnector for decoder. Connect a eurocable to the euroconnector of your decoder and to the special euroconnector of your video recorder. See also the handbook of your video recorder.
Peripheral Equipment Connections 9 $ '& ,1 % 3& ,1387 & (;7 ' (;7 ( (;7 9 9 9 9 ) $17(11$ * 3& $8',2 ,1 + (;7 , +($'3+21( - $8',2 287 7(50,1$/ . &$5' 6/27 < 3E 3U &RPSRQHQW $XGLR ,Q 5 &RPSRQHQW $XGLR ,Q / 6 9LGHR ,Q 9LGHR ,Q $XGLR 5 $XGLR / $XGLR 5 $XGLR / 6XEZRRIHU 2XW - 41 ENG-20710W-17MB16P-1895UK-(LT-20DA6SK)-50076128.p65 41 18.10.
Antenna Connections 2XWGRRU $QWHQQD &RQQHFWLRQV 9+) DQWHQQD 5RXQG RKP FRD[LDO FDEOH 5HDU RI 79 )ODW RKP WZLQ OHDG FDEOH 9+) 8+) DQWHQQD 5HDU RI 79 5RXQG RKP FRD[LDO FDEOH Peripheral Equipment Connections HEADPHONE AUDIO $8',2 ,1 / 9,'(2 ,1 5 VIDEO ,1 ,1 $17 ,1 &$0&25'(5 FOR SATELLITE RECEIVER DECODER - 42 ENG-20710W-17MB16P-1895UK-(LT-20DA6SK)-50076128.p65 42 287 18.10.
PC Input Typical Display Modes The display has a maximum resolution of 1360x768, vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
PC Picture Tips Can not turn the TV on? Check that TV/VCR/DVD switch is set to TV position. If no PC picture appears, check that the DSUB cable is connected properly. Check that your PCs resolution set correctly. See pages 43 for supported modes. TV may go to stand-by mode when you turn the TV on soon after you turn the TV off. If you can turn the TV on again, it is not a problem.
Specifications Item Model LT-20DA6SK Broadcasting Systems PAL BG, DK, I, L, Lp Channels and Digital : 474 MHz - 858 MHz Frequencies Analogue : 46.25 MHz - 862.25 MHz Cable TV Input Signal (S1-S20/ S21-S41) Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync. Horizontal Timing 30 - 69 kHz Vertical Timing 50 - 75 khz Dot Rate 78,75 MHz max.
50076128 ©2005 Victor Company of Japan, Limited 0205MKH-VT-VT
