Color profile: Disabled Composite Default screen ENGLISH CASTELLANO LT-20DA6SSP INTEGRATED DIGITAL WIDE LCD PANEL TV TV CON PANEL LCD PANORÁMICA INSTRUCTIONS MANUAL DE INSTRUCCIONES D Digital Video Broadcasting Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) Number: 4138 50087315 ©2006 Victor Company of Japan, Limited 0506TKH-VT-VT D:\IB Guncel\JVC IDTV 20710 (RM-C1897S UK)\LT-20DA6SSP-17MB16P-10042117\COVER-ENG-ESP-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-1004211
Contents i PC Picture Position Menu ................... 34 PC Picture Menu ................................. 34 Sound Menu ........................................ 35 PIP Picture ........................................... 35 Source Menu ....................................... 35 Sound in PC mode ............................. 35 For your safety ......................................... 2 Where to install ....................................... 5 Important Information .............................
For your safety This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety. They are of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have just purchased.
DONT continue to operate the equipment if you are in any doubt about it working normally, or it is damaged in any way switch off, withdraw the mains plug and consult your dealer. DONT put the empty batteries into garbage instead of recycle bin to reduce harmfull effects to the environment. ABOVE ALL NEVER let anyone, especially children, push anything into holes, slots or any other openings in the case this could result in a fatal electric shock.
WARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down. Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV. Doing so may cause the TV to fall over and lead to injuries.
Where to install WARNING When you install the TV on the wall, only use a JVC wall mounting unit which is designed for this TV. Make sure the TV is installed on the wall by a skilled installer. Locate the TV away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing.
Important Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused by: fire; earthquake; accidental damage; intentional misuse of the product; use of the product in improper conditions; loss and/or damage caused to the product whilst in the possession of a third party; any damage or loss caused as a result of the owner s failure and/or neglect to follow the instructions set out in the owners manual; any loss or da
Control Panel Buttons 32:(5 /$03 ,1)5$5(' 5(&(,9(5 63($.(5 63($.(5 With certain combinations of connectors and leads the back cover may not be easily fitted. If the cover is left off, this in no way infringes safety requirements. -701-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.p65 7 15.06.
Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen 10° backward and 5° forward. Tilt the TV up and down: While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down. -801-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.p65 8 15.06.
Remote Control Buttons / I = (Stand By) button TV / VCR / DVD Switch 9'' Number buttons 79 AV button (EXT-1, EXT-2, EXT-2S, EXT-3, EXT-4, EXT-4S, PC, DIGITAL TV) 5& 9 Colour button MENU = Menu button = Cursor Up button OK button $9 = Cursor Right button BACK = Back button = Volume - /+ buttons GUIDE button TV/RADIO = No Function 0(18 79 '79 PC Control buttons = Hyper Sound On/Off button ZOOM = Zoom button 2.
Features It is a remote controlled Integrated Digital colour television and PC monitor. 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system. It has 2 pieces of Euroconnector socket for external devices (such as video, video games, audio set, etc.) S-Video and AV inputs are available. Optional stereo sound systems (German or German+Nicam) are available. Multilanguage OSD.
Getting Started Follow Step 1 to 7 to set up your TV: Step 1: Checking the accessories supplied Remote control unit x 1 AA/R6 battery x 2 AC adapter x 1 Power cord x 1 Step 2: Inserting batteries Remove the battery cover located on the back of the remote control by gently pulling upwards from the indicated part. Insert two AA/R6 dry cell or equivalent type of batteries inside. Replace the battery cover.
FDUG VRFNHW WHUPLQDOV 100 mm mount based on VESA regulation is equipped. The handle and the stand can be left by loosing the screws with a screwdriver when mounting the TV on a wall. Spread a soft cloth on a flat table and then place the TV on the cloth with the screen facing downwards when you leave the handle and the stand. Step 4: Connecting an aerial VCR and mains Please read the user manual of each device before connecting, to ensure a correct setup.
&RQQHFW D YLGHR GHYLFH $(5,$/ (;7 (;7 $& DGDSWHU 7R '& ,1 9&5 IMPORTANT: Only use the adaptor supplied with this TV. The TV set is designed to operate on 24 V DC. For this, an adaptor is used which gives 24 V DC voltage. Connect this adaptor to a system that supplies 100-240 V AC, 50 Hz. Step 5: Using the cable holder A cable holder which is used to keep the connection cables tidy is supplied.
Step 6: Switching the TV ON/OFF To switch the TV on 35 /LVW (PSW\ 6WDUW DXWRPDWLF VHDUFK Your TV will switch on by two steps: 1- Connect the power supply cord to the system. Then the TV switches itself to standby mode and the power lamp becomes red located on the front of the TV. 2- To switch on the TV from stand-by mode either: Press the , button on the remote control or on the right side of the TV or.
To cancel APS before starting, press BLUE button. SMARTLINK (A trademark of Sony Corporation) First of all choose the Language which the menus of the analogue part of the TV will appear. As soon as you change the language, the menu items will be displayed in the selected language. By pressing the or button, come to the Country item and select the country. This will affect the sort process in APS. Press RED button to start A.P.S.
number buttons) during recording, a message appears asking if you want to stop recording or not. Press OK button to stop recording or BLUE button to continue recording. Do not turn the TV off in the following cases: When recording images from an external device connected to TV (For example camcorder). When recording a TV channel after it has been unscrambled on a decoder. When recording a TV channel by using the TVs output because the VCRs own tuner can not properly receive that channel.
dication of the strength of the signal received on this tuning channel. Operating while watching IDTV Pressing the TV/DTV button at any time while watching television programmes will switch the TV set between displaying the digital terrestrial television broadcasting and its normal analogue broadcasting. It is also used to switch to the last watched mode (TV or DIGITAL TV) from the EXT mode.
You can not set the reminder for the programme which has already started. M Current date and time N Channel listings O Selected date and time P Programme name and broadcast time Q Brief description of the programme No Information is displayed for the programme or channel which does not have any information. You can not set the reminder for these programmes. The programme name, broadcast time and a brief description of the programme are displayed for the programme chosen from the channel listings.
'79 7LPHUV &RQILJXUDWLRQ 7+5(( (GLW 35 /LVW ,QVWDOODWLRQ &RPPRQ ,QWHUIDFH Timers (DTV Timer Recording) By setting the timer, you can record a Digital terrestrial broadcasting (DVB-T) programme with a VCR connected to EXT-2 while you are out. Before using DTV timer recording, the VCR and TV must be connected correctly. For details, see T-V LINK on page 15.
Press the button. WARNING : End: Set the timer end time with the number buttons. When the / buttons are pressed, the input position moves. Press the button. Date: Set the date for the timer to work with the numbers. When the / buttons are pressed, the input position moves. Press the button. Mode: Do not turn off the main power. The timer function will not work with the main power switched off. The TV power lamp begins flashing before the timer start time.
Reactivating the cancelled timer setting Display the TIMER MENU and press the / buttons to choose which timer setting to reactivate. Press the / buttons so that Active appears in the Mode column. Configuration Set the basic setting when watching Digital terrestrial broadcasting (DVB-T). Choose configuration and press the OK button. CONFIGURATION appears. 2. Press the / buttons and choose the language. Language changes every time the button is pressed.
Off: The Edit PR List Favourites settings are disabled. When the / button is pressed, all the channels registered in the Edit PR List can be chosen. Parental Settings Some channels broadcast material which you do not want younger members of the family to watch. Any channel can be locked so that it cannot be selected for viewing without first a four-digit PIN code being entered. In this way any channel not suitable for younger viewers can be protected.
The picture of the chosen channel is shown on the quarter-screen. Deleting a channel 1. Press the / buttons and choose Delete on the bar at the bottom of the screen. 2. Press the / buttons and choose the channel to be deleted, and then press the OK button. The channel deletion confirmation window appears. 3. Choose Yes and press the OK button. (GLW 1XPEHU The chosen channel is deleted. The Edit PR List can be used to do the following: delete registered channels edit channel names.
If you have not changed the PIN code in the CONFIGURATION menus Enter PIN Code (see page 22), input the PIN code you chose. You can either select Factory Settings, effectively resetting the receiver to its factory setting condition, or just search for channels. The lock icon appears next to the channel name in the Edit PR List. When a locked channel is chosen, the Enter PIN code input window will appear. If the correct PIN code is input, the picture appears.
When OK button is pressed, following message will appear on the right bottom side of the screen: eration. $UH \RX VXUH \RX ZDQW WR GHOHWH WKH 35 OLVW DQG UHVHW DOO VHWWLQJV"
When no module is inserted, No CI Module appears. Refer to the module instruction manual for details of the settings. Setting The TV Picture Menu Press MENU button, now you are in main menu. In the Main menu, select Picture using or button, then enter the Picture menu by pressing / or OK button. Menu System Setting Mode Your TVs analogue part has been designed with a menu system to provide an easy manipulation of a multi-function system.
Setting Colour Temp. Setting Sharpness button select Sharpness. or Using Temp. button select Colour Using or Press level. button to increase sharpness Press or button to select Warm, Cool or Normal. Press level. button to decrease sharpness Setting Noise Reduction Using or duction. button select Noise Re- Press or button to select Noise Reduction level Off or Minimum or Medium or Maximum.
Sound Menu As you enter the main menu, sound will be the second item. In the main menu, select Sound using or button, then enter the sound menu by pressing / or OK button. Setting Volume As you enter the sound menu, Volume will be the first selected option. Press button to increase volume. Press button to decrease volume. Pressing or button will turn on or off this feature.
To Store The Settings EXT-2 Output In the Sound Menu, all settings are stored automatically. From EXT-2 Output; TV, EXT-1, EXT-4 or DIGITAL can be given. These modes can be cho- Feature Menu sen by pressing or button on EXT-2 OUTPUT. Press MENU button, now you are in mainmenu. In the main menu, select Feature using or button. Then enter the Feature menu by pressing / or OK button.
Setting VCR ( Video Cassette Recorder ) Mode Selecting Band Band, can be chosen either, This item can be seen in TV, EXT-1, EXT-2, EXT-2S, EXT-3, EXT-4 and EXT-4S modes. C or S by or button. Selecting Channel Channel can be changed by or button or by Digit Buttons. If you want to watch a VCR source from one of these modes, then it will be better to set VCR mode On. For this, while the cursor is on this item press the or buttons to set it On.
To choose a channel in the PROGRAM menu 2. Press the GREEN button to enter the Insert mode. Press / / / button. The programme number that you choose is highlighted in the Program. 3. Press / / / button to choose new programme number. Caution: Using Delete or Insert function rewrite the current channel list in the Program menu. Therefore, the programme numbers of some of channels will change.
Mute Indicator 6RXUFH 79 ',*,7$/ It is placed in the upper middle of the screen when enabled, and it stays there until it is disabled. 79 (;7 (;7 (;7 6 (;7 (;7 To cancel mute, there are two alternatives; the first one is by pressing the button, this volume is set to the preceding value, and the second one is increasing or decreasing the volume level.
Zoom Modes PANORAMIC: Zoom mode can be changed by pressing ZOOM button. You can change the screen size according to the picture aspect ratio. Select the optimum one from the following ZOOM modes. This stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the screen, without making the picture appear unnatural.
Use a D-SUB cable to connect the TVs PC input to the computers RGB output terminal. If you want to listen to the sound from the computer, use an audio cable to connect the PC AUDIO IN to the computers sound output terminal. 3LQ 0LQL ' 6XE &RQQHFWRU Warning: Auto position adjustment recommended to be done with the full screen image for the proper adjustment. Horizontal Position This item shifts the image horizontally to right hand side or left hand side of the screen. Select Hor.
There are four different PIP positions. Programme in the PIP window can be changed by / , digit buttons or AV button. All EXT modes (Except EXT-3) are also available in PIP window. PIP window is removed from the screen by button. Source Menu Sound Menu In the main menu select Sound using or button then enter the Sound menu by In the Main menu, select Source using or button, then enter the Source menu by pressing / or OK buttons.
In PC Mode, if the resolution and the vertical frequency is not supported by the concept, it is displayed an OSD message: Signal out of range Analogue Teletext Teletext is an information system that displays text on your TV screen. Using the Teletext information system you can view a page of information on a subject that is available in the list of contents (index). On screen display is not available in text mode.
Select the required subcode page number by pressing four digit buttons (e.g. 0001). If the selected subcode page is not displayed button. TV in a short time, press programme will be displayed on the screen. Teletext page number will be displayed on the upper left corner of the screen when the selected page is found. Press button to display the selected Teletext page. To exit Teletext Press button. The screen will switch to TV mode.
If you have a device which outputs component video (Y/Pb/Pr), connect it to the EXT-3 terminal with a component video cable and an audio cable. Via the ANT (aerial) socket If your equipment does not have an Euroconnector or RCA jacks, connect it to the TV with an aerial cable. For details, see the manual provided with the equipment. NTSC Playback Connect a NTSC video recorder to a terminal. Then press AV button to select the corresponding AV mode. NTSC 3.58/4.
Peripheral Equipment Connections 9 $ '& ,1 9 9 9 9 % 3& ,1387 & (;7 ' (;7 ( < 3E 3U &RPSRQHQW $XGLR ,Q 5 &RPSRQHQW $XGLR ,Q / (;7 ) $17(11$ * 3& $8',2 ,1 + (;7 , +($'3+21( - $8',2 287 7(50,1$/ . &$5' 6/27 6 9LGHR ,Q 9LGHR ,Q $XGLR 5 $XGLR / $XGLR 5 $XGLR / 'LJLWDO $XGLR 2XW &RD[LDO - 39 01-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.p65 39 15.06.
Antenna Connections 2XWGRRU $QWHQQD &RQQHFWLRQV 9+) DQWHQQD 5RXQG RKP FRD[LDO FDEOH 5HDU RI 79 )ODW RKP WZLQ OHDG FDEOH 9+) 8+) DQWHQQD 5HDU RI 79 5RXQG RKP FRD[LDO FDEOH Peripheral Equipment Connections HEADPHONE AUDIO $8',2 ,1 / 9,'(2 ,1 5 VIDEO ,1 287 ,1 $17 ,1 &$0&25'(5 FOR SATELLITE RECEIVER DECODER - 40 01-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.p65 40 15.06.
PC Input Typical Display Modes The display has a maximum resolution of 1360x768, vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
PC Picture Tips Can not turn the TV on? Check that TV/VCR/DVD switch is set to TV position. If no PC picture appears, check that the DSUB cable is connected properly. Check that your PCs resolution set correctly. See pages 41 for supported modes. TV may go to stand-by mode when you turn the TV on soon after you turn the TV off. If you can turn the TV on again, it is not a problem.
Specifications Item Model Broadcasting Systems LT-20DA6SSP PAL SECAM BG, DK, I, L, Lp Channels and Digital : 474 MHz - 858 MHz Frequencies Analogue : 46.25 MHz - 862.25 MHz Cable TV Input Signal (S1-S20/ S21-S41) Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync. Horizontal Timing 30 - 69 kHz Vertical Timing 50 - 75 khz Dot Rate 78,75 MHz max.