ENGLISH TU-DB1SK DIGITAL TERRESTRIAL SET TOP BOX INSTRUCTIONS Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) Number: 3209
CONTENTS Safety Precautions 2 In the box 3 Over Air Download 3 STB buttons 4 Remote control buttons 5 Preparation 7 Connections 7 Switching on 8 Inithial settings 8 Everyday Operation 9 Changing Channels 9 Channel List 10 Electronic Programme Guide 10 Digital Teletext 11 Widescreen 12 Advanced Operation 12 Configuring Your Receiver 12 Editing The Channel List 13 Channel and Menu Protection 14 Favourite Channels 15 Programme Reminders and Timers 15 Installation 16
SAFETY PRECAUTIONS POWER Always use the provided AC adapter. Operate only from the power source specified (AC 100-240 V,50/60Hz) on the AC adapter. In using, the AC adapter get heat on the surface of the case. It is normal, not defective. Do not be covered with any material on case of AC adapter while it is in operation. Leave the 15 cm space(minimum) around the AC adapter. The rating information and safety caution of the AC adapter are on its case.
IN THE BOX Thank you for buying this JVC Degital Terrestrial Set Top Box. Inside your package you should have: Degital Terrestrial Set Top Box (STB) receiver AC adaptor x1 Remote control unit: RM-C1890S Dry battery for the remote control unit AA (R06) x2 Instruction book Warranty Card Aerial cable x1 Scart cable x1 OVER AIR DOWNLOAD Over Air Download (OAD): To ensure that your STB always has the most up todate information. Please ensure that after use it is set to its standby mode.
RECEIVER BUTTONS Front: 6WDQGE\ EXWWRQ 3URJUDP GRZQ XS EXWWRQV -4-
REMOTE CONTROL BUTTONS 0XWH 6WDQGE\ 6OLGH 6ZLWFK 1XPEHU EXWWRQV ,QIRUPDWLRQ EXWWRQ $9 EXWWRQ &RORXU EXWWRQV 79 '79 EXWWRQ 0(18 EXWWRQ 8S 'RZQ 5LJKW /HIW EXWWRQV 2. EXWWRQ %$&.
REMOTE CONTROL BUTTONS To operate this STB: Set the Slide Switch to STB position. For details of the use of each buttons, see each sections explanation. Note: Volume-/+ buttons and the Mute button work for the volume from the TV. To operate a JVC brand TV or VCR: Set the Slide Switch to the TV/VCR position. Pressing a button that looks the same as the devices original remote control button has the same effect as the original remote control.
PREPARATION Connections Place your receiver on a firm, level surface with at least a 10cm gap around all sides of the case and in a position convenient for connection to your television, a mains power outlet and a TV aerial wall outlet (or the 'flying lead' from your TV aerial, as appropriate). Please refer to the Safety Precautions on page 2.
PREPARATION Switching on Turn on your TV set and select the SCART input (with the AV key, or similar, on the television remote control). Press the [STANDBY] key on the remote control handset. The power lamp change to green and the receiver's menu will be seen on the TV screen. If you do not see the receiver's menu on the television screen, press the AV button on your TV remote control until you see the First Time Installation menu.
If no digital terrestrial television broadcasts are found the receiver will display a message: CHANGING CHANNELS You can choose the channel by using the P / buttons or the number buttons. When using the number buttons, enter the programme number as follows. Example: PR6 You should then refer to the Troubleshooting Guide on page 20 to establish the cause of the problem.
Icons are also displayed in the information banner and if this channel is a favourite channel (see ADVANCED OPERATION - Favourite Channels on page 15). favorite channel icon If the selected channel is locked (see - ADVANCED OPERATION - Channel Protection on page 14), you must enter the correct four digit code to view the channel. Here, you can preview any channel stored by the receiver before viewing it full screen.
You can change the day by pressing [BLUE] or [YELLOW] keys. Pressing [YELLOW] will display events of the next day. Pressing [BLUE] will display the events of the previous day. You can return to normal television viewing (to watch the channel last selected in the EPG screen) by pressing the [GUIDE] key again, or the [MENU] key.
WIDESCREEN TV sets are available with screens of the standard (4:3) format and widescreen (16:9) format. When you first installed your receiver you specified the format of the connected TV (this can now be altered i f n e c e s s a r y ; s e e S e c t i o n 3 - A D VA N C E D OPERATION - Configuring Your Receiver). Digital terrestrial television broadcasts are also made in both standard and widescreen formats.
SYSTEM TV OUT Use LEFT/RIGHT buttons to toggle System Menu Language. Press OK on the preferred language. Use LEFT/RIGHT buttons to toggle Country options. Press OK on the preferred Country. The receiver can output either an RGB/Y/C,Video signal from the TV SCART on the rear panel. Although the RGB format results in a better quality picture, not all equipment - particularly some VCRs - can cope with an RGB signal (see Appendix C Connecting A VCR).
SELECT Hint This function selects a channel for viewing and is an alternative to using the [P+] and [P-] keys, channel number or EPG. Highlight the channel to be viewed, highlight the OK button at the base of the screen using the [LEFT] or [RIGHT] keys and press [OK]. The highlighted channel now appears in the image window and you can leave the Channel List to view the channel by pressing [MENU]. You can also enter a channel name using the number keys on the remote control.
FAVOURITE CHANNELS There will be some channels that you tend to watch more often and some only occasionally. Although some duplicate channels you may want to delete from the channel list, others although not watched frequently, you will not want to do away with altogether. The favourite mode allows the mostwatched channels to accessed more easily, leaving the less-watched channels accessible but out of the way.
EVENT TIMER Hint You can also set a timer to switch the receiver to any channel without your intervention. Thisis intended for making video recordings of programmes when you are out. If a single programme is to be recorded, the receiver can be left switched to the required channel and the timer set on the VCR. However, if two or more programmes on different channels are to be recorded then the receiver's own timer is set as well, to select the required channel when it is needed.
FIRST TIME INSTALLATION To reset the receiver, highlight the First Time Installation line in the menu and press [OK]. A warning screen is displayed in case of accidental operation. This is for searching for digital channels on a single broadcast frequency. The frequency channel number (21-69) is entered in the box at the top left of the screen and the received signal level and signal quality can be observed on the two bar graphs at the bottom.
SPECIFICATION GENERAL Broad casting system DVB-T 2k & 8k Video system PAL Number of preset channels 200 Channel frequencies 474 - 858 Mhz Stereo system MPEG Layer I & II 32/44.1/48 KHz Power requirements DC 6V, AC adapter: 100 - 240V, 50/60 Hz Terminals U/V Input PAL type U/V Output PAL type SCART-1 (TV) RGB, Y/C, Video output and Audio output are available. SCART-2 (Aux) RGB, Y/C, Video output, Audio output and Video input are available.
CONNECTING THE EXTERNAL DEVICES If your TV and VCR both have two scart sockets you can connect as follows.Unplug the aerial lead and connect this to the ANT IN socket on the rear of your receiver. Connect the aerial lead (supplied) from the LT OUT on the receiver to the ANT IN on the rear of the VCR. Then connect an aerial lead from the LT OUT on the VCR to the ANT IN socket on the rear of your TV. If your VCR has only one scart socket, connect only Scart 1 to VCR.
TROUBLESHOOTING GUIDE If you experience problems with the receiver or its installation, in the first instance please read carefully the relevant sections of this User Guide and this Troubleshooting section.
50053794 ©2004 VICTOR COMPANY OF JAPAN, LIMITED C 2004 Victor Company of Japan, Limited 0804MKH-VT-VT