VR-N1600_J.book Page 1 Wednesday, August 8, 2007 4:17 PM NETWORK VIDEO RECORDER VR-N1600U VR-N1600E STARTUP GUIDE WARNING LIVE/BROWSE 㧝 㧞 㧟 㧠 SELECT 㧡 㧢 *1/' 㧣 㧤 PTZ/PRESET 㧥 ALARM OPERATE REV FWD HDD LOCK REC CONTROL FUNCTION SERIAL CANCEL ZOOM OUT ZOOM IN SEARCH KEY ALARM CLEAR REC/STOP STOP(PB) PLAY SKIP Powered by Milestone Please read the following before getting started: Thank you for purchasing this JVC product.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.book Page 2 Wednesday, August 8, 2007 4:17 PM Getting Started Features Motion Detect Enables recording to start automatically when AmotionB is detected in the preset live image. You can also specify the detection area for each camera. Automatic detection of network cameras Alarm Mail Notification Reduces the hassle of complex camera registration procedures. Enables notification by e-mails to be sent out when an alarm or motion is detected.
VR-N1600_J.book Page 3 Wednesday, August 8, 2007 4:17 PM Contents Getting Started Features ............................................................................ 2 Contents ............................................................................ 4 Precautions for Proper Use of this Product ....................... 6 Part Names and Functions ................................................ 8 Mounting to a Rack .........................................................
VR-N1600_J.book Page 4 Wednesday, August 8, 2007 4:17 PM Getting Started Precautions for Proper Use of this Product Locations of Storage and Use 䢇 Do not store the unit at the following places. Doing so may cause the unit to malfunction or break down.
VR-N1600_J.book Page 5 Wednesday, August 8, 2007 4:17 PM Precautions when Moving this Unit Others 䢇 Remove all connected cords before moving Turn off the power and remove the power plug before moving this unit. Failure to do so may cause damage on the cords, and result in fire or electric shock. 䢇 Moving of this unit or installation work is strictly prohibited when the power of this unit is on or immediately after the power is turned off (approximately 1 minute).
VR-N1600_J.book Page 6 Wednesday, August 8, 2007 4:17 PM Getting Started Part Names and Functions Front S T A B R WARNING LIVE/BROWSE 㧝 㧞 㧟 㧠 SELECT 㧡 㧢 *1/' 㧣 㧤 PTZ/PRESET 㧥 ALARM OPERATE REC CONTROL Q REV FUNCTION CANCEL ZOOM OUT ZOOM IN ENTER CD E P O LOCK SERIAL SEARCH KEY ALARM CLEAR REC/STOP STOP(PB) PLAY SKIP F GHIJ K L M A [OPERATE] Button/Indicator Switches operation on or off.
VR-N1600_J.book Page 7 Wednesday, August 8, 2007 4:17 PM Memo : ● The manual recording mode executes recording from all cameras regardless of the settings in the [Camera Record Setting]. Recording is carried out in accordance with the frame rate selected in [Camera Record Setting]. L [STOP(PB)] Button Stops playback when you press this button in the playback mode. M [PLAY] Button Plays back at the speed and in the direction specified by the Shuttle Dial position.
VR-N1600_J.book Page 8 Wednesday, August 8, 2007 4:17 PM Getting Started Part Names and Functions (continued) Rear Panel d POWER U ON AUDIO IN AUDIO OUT LAN2 ALARM IN OFF V LAN1 VGA OUT 1 2 3 4 SERIAL SIGNAL GND W XY Z U [POWER] switch Switches the power on or off. Memo : ● Be sure to press and hold down the [OPERATE] button on the front panel to shut down the system before switching off the power supply.
VR-N1600_J.book Page 9 Wednesday, August 8, 2007 4:17 PM Rear I/O Terminals e ON AUDIO IN AUDIO OUT fhjl n gikm o LAN2 ALARM IN OFF LAN1 VGA OUT 1 2 3 4 SERIAL SIGNAL GND p 䡵 Input ports 䡵 Output ports e [ALARM IN 1 to 8] alarm input terminals 1 to 8 j [COMMON] signal ground terminal Alarm recording is activated when signals are input to these terminals. This is a common ground terminal. Connect it to the signal ground terminal on the connected device.
VR-N1600_J.book Page 10 Wednesday, August 8, 2007 4:17 PM Getting Started Part Names and Functions (continued) Mounting to a Rack Use the supplied rack mount bracket to mount VR-N1600U/E to the EIA rack. 1 Mount the rack mount bracket using screw (1) Rear I/O Terminals Terminal e[ALARM IN] Remarks 250 ms and above 250 ms and above Make Break Make Contact Input 2 Remove screws B of the foot (4 pcs) at the bottom ● Remove the foot.
VR-N1600_J.book Page 11 Wednesday, August 8, 2007 4:17 PM Preparation System Connection Example The following operations are possible with this system.
VR-N1600_J.book Page 12 Wednesday, August 8, 2007 4:17 PM Preparation System Connection Example (continued) Note : ● Do not connect LAN1 to the internet. If the internet is busy or the relay equipment fails, you may not be able to save important camera images. To maintain full recording capacity, it is recommended that a dedicated network be used. Be sure to connect the LAN1 camera network to the same segment. (Do not use the address translation of NAT and NAPT etc. or a router.
VR-N1600_J.book Page 13 Wednesday, August 8, 2007 4:17 PM 2 Check to ensure that the camera is detected Selecting a language The [Language Setting] screen appears when you start up VR-N1600U/E for the first time. Select the language to use using the steps below. ● After the message disappears, a list of detected cameras is displayed. ● If all the cameras are not detected, press the [Auto Detect] button again.
VR-N1600_J.book Page 14 Wednesday, August 8, 2007 4:17 PM Preparation During Initial Startup (continued) 6 Enter the password for the network camera ● Press the [KEY] button to display the software keyboard. ● Use the keypad to move the mouse cursor over the software keyboard. ● Pressing the [16/ENTER] button inputs the characters on the keyboard into the password field.
VR-N1600_J.book Page 15 Wednesday, August 8, 2007 4:17 PM C Use the [7/B] button to display the camera Memo : ● Use [SKIP] to move between the items. ● Use the [2/D] and [10/0/E] buttons to select the item to configure. ● To enter numeric characters, press the [SELECT] button to turn on the light of the [SELECT] indicator. Upon entering the numeric characters, press the [PTZ/ PRESET] button to turn on the light of the [PTZ/PRESET] indicator.
VR-N1600_J.book Page 16 Wednesday, August 8, 2007 4:17 PM Basic Operation Viewing Live Images via Front Panel Control This section describes the procedures for viewing live images by using the front panel of VR-N1600U/E. 2 Press the [15/ZOOM IN] and [14/ZOOM OUT] buttons to select a view Note : ● Do not switch the view frequently within a short time interval. ● When live images do not appear on VN-C625/VN-C655, set the password on the camera unit as well as VRN1600U/E again.
VR-N1600_J.book Page 17 Wednesday, August 8, 2007 4:17 PM 䡵 Pan/Tilt Memo : A Event indicator (Left: yellow) Lights up when events specified in the [Camera Record Setting] occur. The indicator appears black if event indication has not been specified for the camera in question, or if no specified event has occurred. B Motion indicator (Center: red) Lights up when motion is detected. Blinks every time an image is received from the camera.
VR-N1600_J.book Page 18 Wednesday, August 8, 2007 4:17 PM Basic Operation Playing Back Recorded Images via Front Panel Control This section describes the procedures for playing back recorded images using the front panel of VR-N1600U/E. Displaying the [Browse] Screen 1 Press the [LIVE/BROWSE] button when the wallpaper or main menu screen is displayed ● The NVR Viewer starts up and the [Live] screen appears.
VR-N1600_J.book Page 19 Wednesday, August 8, 2007 4:17 PM 䢇 Playing Back Adjusting the Playback Speed (Jog/Shuttle Playback) 1 Press the [PLAY] button ● Playback starts from the date/time indicated in [Master Time] of [Time Navigation]. ● Images are played back according to the angle of the shuttle dial (x1/20, x1/5, x1, x2, x5, x10, x20). [Master Time] area NVR Viewer You can adjust the playback speed by turning the jog dial/ shuttle dial on the front panel.
VR-N1600_J.book Page 20 Wednesday, August 8, 2007 4:17 PM Others Troubleshooting Symptom Action Power cannot be turned on. Check to ensure that the power cable has been plugged in correctly. Check to ensure that the power switch on the rear panel is switched on. Camera is not automatically detected. Follow instructions in the camera’s [Instruction Manual] to check the IP address settings. When the IP Lease feature is in use, turn off and on the power of the camera when VR-N1600U/E is started up.
VR-N1600_J.book Page 21 Wednesday, August 8, 2007 4:17 PM Specifications 䡵 Attachments/Accessories VR-N1600U Start-up Guide ....................................... 1 CD-ROM................................................ 1 Power Cord (2 m) .................................. 1 䡵 General Rack Mount Bracket .............................. 2 Allowable Operating Temperature Warranty Card ....................................... 1 Service Information Card.......................
VR-N1600_J.
VR-N1600_J.
VR-N1600_J.