INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D’UTILISATION GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI INSTRUÇÕES INSTRUKTIONSBOG KÄYTTÖOHJE BRUKSANVISNING BRUKSANVISNING NÁVOD K OBSLUZE INSTRUKCJA OBSŁUGI HASZNÁLATI UTASÍTÁS ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ 使用說明書 ဧႁීၗ 사용 설명서 DEUTSCH FRANÇAIS NEDERLANDS CASTE.ESP.
In order to use this product safely Preparation (墌 pg. 4) • Check that there is no dirt, cracks, or damage to the O-ring. • Always apply grease to the O-ring. Attaching the Marine Case to the Camera (墌 pg. 5) • Make sure that the O-ring is not twisted, and that you do not forget to attach it. • When tightening the seal, make sure there are no foreign objects caught in the seal. Recording the Video/Still Image Files (墌 pg. 6) • Avoid opening and closing the marine case in the shooting location.
. Check that there are no scratches or cracks on the marine case every time you use it. The marine case must withstand water pressure with use. Repeated exposure to pressure eventully leads to material fatigue, which may result in damage of the marine case. Every time you use the marine case, check in advance that there are no scratches or cracks. If you frequently use the marine case, be sure to ask for maintenance at the store of purchase. (There is a charge for maintenance.
Index Preparation 1 Inspect the main casing for scratches and cracks etc. Apply 2 or 3 drops of the glass cleaner provided onto one of the lens tissues or a clean cloth, and wipe the inner side of the marine case front glass. Strap Front glass 2 Using the supplied pick, remove the O-ring from the main case. Bottom view ! Main casing grip: Attach the included strap as shown in the diagram above. # Zoom lever $ Ring: Commercially available filters (67mm diameter) etc can be attached.
Attaching the Marine Case to the Camera 1 5 Insert the camera into the marine case. Inserting the provided silica gel between the camera and marine case prevents the inside of the marine case from steaming up. Pull the power/mode switch lever of the marine case in the direction of the arrow (Q), and rotate it to lock it (R). Silica gel If the power/mode switch lever is not locked, it may touch or damage the camera when the camera is put into the case. Tighten the grip belt.
Recording the Video/Still Image Files 2 Before recording Submerge the marine case with the camera equipped into a bathtub or water tank full of fresh water. Gradually increase the amount of time the marine case is submerged as shown below. • 1st time: 5~10 seconds • 2nd time: 30 seconds ~ 1 minute • 3rd time: 3 minutes ~ 5 minutes (try operating the levers and buttons while the marine case is submerged). Press the video recording start/stop button or the still image shooting button to start recording.
Detaching the Marine Case/Maintenance Always perform maintenance on the marine case after you have finished recording. Failing to perform maintenance on the marine case will allow dirt to build up on the case, causing water leaks. 1 Wash the marine case in water while it is still sealed. • If the marine case was used in seawater, we recommend submerging the marine case in fresh water for a while to remove salt.
© 2007 Victor Company of Japan, Limited Printed in Japan 0307FOH-AL-VP
WR-MG88_EN_A5.
WR-MG88_EN_A5.book Page 2 Thursday, May 3, 2007 9:06 AM Procedures for Using the Strap (J Page 4) Pass the strap through the strap attachment hole before using the marine case to maintain a firm grip in water. Silicon cloth Wash the marine case with fresh water, and wipe the outer side with the silicon cloth after drying. Strap attachment hole Buckle opener (Hexagonal wrench (small)) Buckle Grip belt of camera (J Page 5) For use when you have difficulty opening the buckle.
WR-MG88_EN_A5.book Page 3 Thursday, May 3, 2007 9:06 AM Supplied Maintenance Kit Glass cleaner (J Page 4) (to prevent fogging) Apply the glass cleaner on the front glass before using the marine case. Add two to three drops of the cleaner on a lens tissue paper, and wipe the inner side of the front glass. Marine case Front glass Cleaner liquid (J Page 7) For removing dirt from the front glass after using the marine case.
WR-MG88_EN_A5.book Page 4 Thursday, May 3, 2007 9:06 AM O-ring Rubber ring for waterproofing. Check to ensure that the ring is not twisted and foreign materials are not attached, followed by attaching it to the designated position. Dirt, sand, salt crystals, etc. Hair, thread, etc. O-ring Swab For cleaning the O-ring groove. Press it lightly against the O-ring groove and move it around the circumference of the groove.
WR-MG88_EN_A5.book Page 5 Thursday, May 3, 2007 9:06 AM Pick For removing the O-ring. To remove the O-ring, insert the pick between the O-ring and the O-ring groove. Pick O-ring O-ring groove Silicon grease For protecting the O-rings and preventing water leakage. Check to ensure that there is no foreign substance on the O-ring before applying the grease. Squeeze about 1 cm of the grease onto your finger, and apply it on the O-ring by holding the O-ring with your fingers.
WR-MG88_EN_A5.fm Page 6 Wednesday, May 9, 2007 10:06 AM After shooting (sea salt removal) Make sure to perform maintenance on the marine case. Salt crystal or dirt will accumulate inside the marine case if maintenance is not performed, and this may cause water leakage. A Prepare a container that contains fresh water that is five times more than the volume of the marine case.
WR-MG88_EN_A5.fm Page 7 Monday, May 14, 2007 8:52 AM E Face the front glass of the marine case upwards, and open the buckles to remove the camera, while paying attention not to let water droplets at the O-ring or buckles enter the case. Front glass F Upon removing the camera, close the marine case again while paying attention not to allow water droplets enter the case, followed by tightening all the buckles. G Final salt removal Submerge the marine case in fresh water for at least 1 hour to remove salt.
BackCover.