Owner manual

ManualsBrandsK-Edge ManualsFor bicyclesK13-510-[color]

WARNING: IT IS STRONGLY RECOMMENDED THAT YOU PERIODICALLY CHECK ALL BOLTS FOR PROPER TORQUE!!!

GARMIN TT Mount Installation Instructions

(K13-510-[color])

Description:

The K-EDGE GARMIN TT Mount is designed for installation of a GARMIN Edge or GARMIN Forerunner computer onto a 22.0-

22.5mm diameter time-trial handlebar. Unlike any other GARMIN TT mount, our design places the GARMIN computer within the TT

bars of the bike, providing a 'clean'/'flush' look while still retaining functionality of the GARMIN computer.

A new 'Twist-Lock' design was engineered to allow the placement of a GARMIN computer between TT bars. This 'Twist-Lock'

feature allows a GARMIN computer to remain stationary (between TT bars) while a lever at the bottom allows the GARMIN insert to

rotate 90-degrees and securely lock a GARMIN computer onto the TT bars. There is no need to rotate the GARMIN computer to

lock it into place.

In addition, the 'Twist-Lock' design inherently lends itself to an automatic compatibility with Forerunner computers (with 'quick-release

kit' purchased separately from GARMIN); simply operate the lever in the reverse direction. Tools are not necessary when properly

installed.

Vertical placement was dependent on function; accessing side buttons from underneath the TT bars while securing a GARMIN

computer to the TT. Precise vertical placement for button access was critical in the design of our mount in order to maintain a

'clean'/'flush' look.

Compatibility:

The K13-510 GARMIN Mount is compatible with all GARMIN Edge 200, 500, 510, 800, and 810 computers. It is also compatible

with the GARMIN Forerunner 310XT (with 'quick-release kit' purchased separately from GARMIN) computers utilizing the same

mounting system. Please refer to the 'Minimum TT Bar Width' section of this document for proper fitment.

Warnings:

These instructions are generalized to accommodate a wide range of setups for a bike. If your setup does not match these

descriptions, take extra care in the process of your setup and contact K-EDGE Technical Support if you have any questions.

Improper installation of any K-EDGE product or use outside of its design intentions could lead to not only damaging the bike and

related components but could also cause personal injury to the rider.

Summary of content (5 pages)

PAGE 1
GARMIN TT Mount Installation Instructions (K13-510-[color]) Description: The K-EDGE GARMIN TT Mount is designed for installation of a GARMIN Edge or GARMIN Forerunner computer onto a 22.022.5mm diameter time-trial handlebar. Unlike any other GARMIN TT mount, our design places the GARMIN computer within the TT bars of the bike, providing a 'clean'/'flush' look while still retaining functionality of the GARMIN computer.
PAGE 2
Parts Included:  K13-510  1x K-EDGE GARMIN mount  2x M3 x 8 mm SHCS  2x M3 x 6 mm FHCS (Blue Thread Lock applied) Tools/Items Required:  Metric Allen Set (2.
PAGE 3
Mount Installation: NOTE: The K13-510 clamp is designed to function as a 'single-piece' clamp when installed properly, meaning that one end of the clamp 'contacts' the arm first while the other end has a 'gap' for the final clamping pressure. CAUTION: Due to the clamping design and bolt thread engagement, maintain a torque of 1.5 N-m MAX or bolt failure will result. 1. Remove the 2x M3 x 8mm bolts from the upper clamp half (K13-512) 2.
PAGE 4
Lever Action Adjustment: NOTE: The K13-510 is factory-assembled for immediate use with GARMIN Edge/ Forerunner computers without any adjustment necessary, IF you wish to adjust the lever action of the TT mount, please follow the steps below to adjust the insert (K13-503). 1. Loosen the 2x M3 x 6mm Flat Head Screws holding the K13-503. 2. Slowly tighten the 2x M3 x 6mm Flat Head Screws holding the K13-503 (see diagram above). 3.
PAGE 5
Troubleshooting:  My computer hits my left TT bar when installed on the mount. o Check that your TT bars meets the minimum bar width and adjust as needed.  There is a little play even when my computer is installed onto the mount with a positive click. o With the computer installed, visually check for movement between the insert (K13-503) and the arm (K13511). If movement is detected slightly increase the torque of the 2x M3 x 6mm Flat Head Screws (1 N-m Max).