BTH80P True Wireless Bluetooth Headset User’s manual
Contents Brief introduction…………...…………………………..…... 1 Before use……………………………………………………. 1 1. Overview…………………………………………………...……1 2. Charging for headset..……………………………………………2 2. Charging for charging case.. …………………………………2 Getting started……..…………………………………………3 1. Wearing headset.............................................................3 2. Mono & Twin Modes.............................................................5 3. Earbuds pairing/connecting........................................................
Welcome to use this True Wireless Bluetooth headset, BTH180P, Please read this user’s manual carefully before use. Brief introduction BTH180P is a true wireless Bluetooth headset. The earphones on the left and right sides adopt a separate design, which can be used in different occasions according to personal usage habits. There is no need to connect the earphone cable between the two earphones. It can be used with a single earphone or can realize stereo effect through Bluetooth connection.
1 MFB touch-button 6 Type-C charging jack 2 7 3 LED indicator (Red and blue) Microphone 8 Wireless charge induction area Earhook 4 Top case 9 Charging pins 5 Charging indicator light 2. Charging for earbuds When the headset is low on power, it emits the red light flashing slowly 4 times every 14s. Please recharge the battery of the headset. The way of charging for the earbuds as following: 1.
Remarks: Please place the L and R earphones in the correct charging compartment according to the L and R marks on the charging box to charge them. 3. Charging for charging case When any of the following situations occurs, it indicates that the charging case will be low power. You need to charge the charging case: 1) When the indicator of the charging case has only one white light on, it means the battery of the charging case is low.
Type-C charging Wireless charging Remarks: The indicator light of the charging box is off when the earphone in the idle state（not in charged）. Open the cover of the charging box, the 4 white indicator lights of the charging box will light up in sequence, and the indicator lights will go out after about 5s. Indicates that the current charging box power level from low to high is one, two, three, and four white lights flashing.
Getting started 1. Wearing headset with earhook a. Choose the right earphone to match the ear b. Align the earphone with the ear and insert the ear tip into the ear hole C.Rotate the earphone to a comfortable position 2. Without earhook a. Choose the right earphone to match the ear b. Align the earphone with the ear and insert the ear tip into the ear hole C.
3.Mono mode Each earbuds can be connected singly to the cellphone. 1. Power on 1)In the charging state, open the charging box top case or take the earphone out of the charging box, and the earphone will automatically turn on. 2)If the earbuds are power off, you should press touch-button for about 3s until blue LED flashes as the same time the earbuds emits “Power on”. Then release. This is now in the “Power on”state. 2.
4.Power off 1）Auto power off once put into charging case 2）Press touch-button about 5s and release it till red LED is on,and earbuds prompt “Power off”. Remark: When the earbuds are idle and not connected to the Bluetooth device, they will automatically enter the pairing mode after 10 seconds. The pairing mode will last for 5 minutes. If it is not paired with any mobile phone after 5 minutes, the earbuds will shut down automatically. 5.
6.Pair and connect the left and right earphones (when the two earphones cannot be connected automatically) 1. Put the left and right earphones into pairing state respectively (red and blue lights flash alternately). 2. When the headset is in the pairing state, press the touch button in 5 consecutive taps, and see that the red light turns to red and blue lights alternately and slowly flashing after 1 second, which means the headset has entered TWS pairing mode. 3.
Balance Playing music N/A triple--click touch-button Right Balance 2.
Turn off ambient sound Connected with phone N/A Press and hold the touch bottom 4s Game mode Connected with phone triple--click touch-button N/A Exit Game mode Connected with phone triple--click touch-button N/A Audio pass through off Enter gaming mode exit gaming mode N/A Volume up Short press touch-butt on During a call Short press touch-button Volume down During a call N/A There is no prompt sound during operation, and the maximum volume prompts Maximum There is no prompt sound duri
When the earbuds are connected to an IOS device or some of the Android device, it will display the battery of earbuds on the device. When the earbuds is low on power ,the battery indicator will turn red and show a depleted battery icon. For different phones, there may be different ways to display the battery life on the phone. The following is a screenshot of the battery life on the iOS phone. Full charge 8.
represents the current battery power of the charging case. According to the power level from low to high, there are 1, 2, 3 and 4 white LED on.After flashing, it lights for about 5s and then goes out During the charging process, the number of white lights on the charging box represents the current battery power of the charging box.
lights alternately flash quickly), and you need to click on the phone to repair. Care and maintenance Read the following recommendations carefully before using BTH180P. Following these you will be able to enjoy this product for many years. Keep it dry and don’t put it in the damp place to avoid the product’s internal circuit being affected. Don’t wear the headset when in strong exercise to avoid sweat enter.
b) Make sure the headset connects with the mobile phone correctly; c) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 4. Why can’t I hear the sound clearly on the headset? a) Make sure the mobile phone is in the strong signal area; b) Make sure the headset is in the available range. and no other block。 5.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
