Owners manual

ManualsBrandsK&N Filters ManualsAutomotive57-1001 Filtercharger Injection Performance Kit









































TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

PARTS LIST:

Description Qty. Part #

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

2. Release the locking tab and disconnect the

mass air sensor electrical connection.

3. Remove the two factory air box mounting bolts

shown.

BMW 3 SERIES (E46)

2001-05 330CI, I

2002-05 330XI

2000 330xi

L6-3.0L

Flat Blade Screwdriver

Ratchet

Extension

10mm Socket

10mm Wrench

4mm Allen

A Intake Tube 1 087138

B Grommet; Black, Rubber 1 08100

C Hose Clamp; #56 2 08620

D Silicone Hose 1 08630

E Nut; 6mm Nylock 3 07553

F Washer; 1/4”OD X 5/8”OD, Flat 3 08275

G Washer; 1/4”ID X 1”OD, Fender 2 08160

H Washer; 1/4” Split Lock 1 08198

I Bolt; M6-1.00 X 20mm 2 07730

J Bracket “C” 1 010087

K Heat Shield 1 07495

L Edge Trim 50” 1 102481

M Hose Clamp # 60 1 08624

N Air Filter 1 RC-4630

4. Loosen then hose clamp which secures the

factory intake tube to the mass air sensor, then

disconnect the intake hose from the mass air sen-

sor as shown.

5. Unhook the wiring harness retainer shown from

the rear of the box.

6. Lift the air box from the rear and remove it from

the vehicle.

NOTE: Pull the air box backwards to dislodge

the upper and lower fresh air intake.

57-1001

Summary of content (3 pages)

PAGE 1
57-1001 BMW 3 SERIES (E46) 2001-05 330CI, I 2002-05 330XI 2000 330xi L6-3.0L TOOLS NEEDED: Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen PARTS LIST: Description A B C D E Intake Tube Grommet; Black, Rubber Hose Clamp; #56 Silicone Hose Nut; 6mm Nylock Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Pull up on the vent tube to dislodge it from the intake tube as shown. 13. Insert the factory vent tube into the grommet in the intake tube as shown. 19. Unhook the two mass air sensor retaining clips and remove the mass air sensor from the air box. 8. Loosen the lower hose clamp, which secures the upper intake tube to the lower intake tube, and then remove the upper intake tube from the vehicle. NOTE: K&N Engineering, Inc.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 26. The C.A.R.B. exemption sticker, (attached), must be visible under the hood so that an emissions inspector can see it when the vehicle is required to be tested for emissions. California requires testing every two years, other states may vary. 24. Reconnect the mass air sensor electrical connection. 25. Reconnect the vehicle’s negative battery cable. Double check to make sure everything is tight and properly positioned before starting the vehicle. 27.