Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 57-6014 FIPK Performance Air Intake System

57-6014

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

PARTS LIST:

Description Qty. Part #

NOTE: This kit was not designed

to ﬁ t vehicles with a body lift.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before discon-

necting the negative battery cable. Some radios

will require an anti-theft coded to be entered

after the battery is reconnected. The anti-theft

code is typically supplied with your owner’s

manual. In the event your vehicles’ anti-theft

code cannot be recovered, contact an autho-

rized dealership to obtain your vehicles anti-

theft code.

TO START:

2. Disconnect the mass air sensor electrical connec-

tion and unhook the harness from the air box.

Nissan

2005-07 Frontier / Pathﬁ nder / Xterra

V6-4.0L

Flat Blade Screwdriver

Phillips Screwdriver

Ratchet

Extension

10mm Socket

13mm Socket

10mm Wrench

Pliers

A Hose Clamp #48 3 08601

B Hose Silicone 1 08622

C Intake Tube 1 087177

D Hose; 1/2”ID x 17”L, Silicone 1 08177

E Screw; M4-.7 x 12mm, B/H/A 2 07726

F Spacer 2 06503

G Bracket 1 070106

H Bolt; 6mm-1.00 x 16mm Hex 6 07703

I Washer; 1/4” Lock 3 08198

J Washer; 1/4”ID x 5/8”OD Flat 13 08275

K Nut; 6mm Nylock 7 07553

L Stud; M6 M/M Rubber MNTD 2 07027

M Bracket; Lg. “L” 1 010051

N Heat Shield 1 07689

O Edge Trim 1 102503

P Bracket; Sm. “L” 1 07805

Q Bracket; Med. “L” 1 070632

R Bolt; 8mm-1.25 x 16mm Hex 1 07844

S Washer; 8mm Wave 1 08239

T Washer; 5/16”ID x 5/8”OD Flat 1 08276

U Hose; Step Silicone 1 08051

V Hose Clamp #56 1 08620

W Adapter #380 1 21512

X Hose Clamp #104 1 08697

Y Air Filter 1 RF-1014

3. Remove the two bolts shown, which secure the

engine cover.

4. Lift ﬁ rmly on the engine cover to dislodge it from

the mounting grommets, and then remove the cover

from the engine as shown.

5. Remove the two bolts shown which secure the

stock intake tube to the engine.

6. Using pliers, loosen the spring clamp which

secures the crank case vent hose to the valve cover

and then remove the hose from the valve cover as

shown.

7. Loosen the two hose clamps shown which se-

cure the stock intake tube to the air box and to the

throttle body.

8. Remove the intake tube from the vehicle as

shown.

9. Remove the air box retaining bolt shown.

Summary of content (3 pages)

PAGE 1
57-6014 Nissan 2005-07 Frontier / Pathfinder / Xterra V6-4.0L O NOTE: This kit was not designed to fit vehicles with a body lift. K H I TOOLS NEEDED: Flat Blade Screwdriver Phillips Screwdriver Ratchet Extension 10mm Socket 13mm Socket 10mm Wrench Pliers J P Y J H J J E F J K F H JM I K J J J K H G 6 3 13 7 2 1 1 07703 08198 08275 07553 07027 010051 07689 PARTS LIST: A B C D E F G Description Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Pull firmly on the air box to dislodge it from the mounting grommets and remove it from the vehicle. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 11. Remove the two air box mounting studs shown from the inner fender. 12. Install the “L” bracket (070632) onto the heat shield as shown with the provided hardware. 13. Install the “L” bracket (010051) onto the heat shield as shown with the provided hardware. 16.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 28.