Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N Performance Cold Air Intake Kit 63-1114 with Lifetime Filter for Dodge Challenger/Charger, Chrysler 300 5.7L V8

63-1114

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

TO START:

PARTS LIST:

Description Qty. Part #

2009 Challenger

2008-09 Charger RT

2008-09 300C RT

2008 Magnum RT

V8-5.7L HEMI

2008-09 Challenger

2008-09 Charger SRT8

2008-09 300C SRT8

2008 Magnum SRT8

V8-6.1L HEMI

4mm allen

3/4” drill bit

10mm socket

13mm socket

10mm wrench

drill

ﬂ at blade screwdriver

hack saw

ratchet

A Hose Clamp #56 5 08620

B Silicone Hose 3.50”ID x 2.0”L 2 08630

C Grommet 1”OD x 1/2”ID 2 08064

D Silicone Hose 1/2”ID x 17”L 1 08177

E Intake Tube (EM) 1 087153

F 90 Degree Vent Elbow Blk. 1 08065

G Bolt 6mm x 1.00 x 20 FHA 1 08376

H Saddle Bracket 1 078855

I Cup Washer 1 08180

J Bracket 1 010088

K Flat Washer 1/4” 6 08275

L 6mm Nylock 4 07553

M Bolt 8mm x 1.25 x 35 1 07784

N 8mm Wave Washer 1 08239

O Flat Washer 5/16” 1 08276

P Spacer .625”ID x .625”L 1 07849

Q Edge Trim 30”L 1 102489

R Edge Trim 39”L 1 102496

S Heat Shield 1 07498

T Bolt 6mmx1.00 x 16 2 07703

U Small L Bracket 1 070066

V Twist Bracket 1 070772

W Bolt 6mm x 1.00 x 20 1 07865

X Fender Washer 1/4” x 1” 2 08160

Y Hose Clamp #104 1 08697

Z Adapter #380 1 21512

AA Air Filter 1 RF-1042

2. Lift up on the engine cover to loosen it from

the mounts, and then remove the cover from the

vehicle.

3. Unlock the red locking tab on the air tempera-

ture sensor electrical connection, then depress the

locking lever and pull apart the temperature sensor

electrical connection.

4. Loosen the hose clamp that secures the intake

tube to the throttle body and pull the intake tube off

of the throttle body.

5. Disconnect the crank case vent hose from the

valve cover port as shown.

5a. On SRT-8; 6.1L vehicles, disconnect the crank

case vent hose from the air box as shown.

6. Loosen and remove the air box mounting bolt as

shown.

7. Lift the complete intake and air ﬁ lter assembly to

remove it from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

8. Install the twist bracket (070772) onto the core

support using the hardware provided through the

existing hole as shown.

NOTE: Use the two fender washers provided to

sandwich the core support. Do not completely

tighten at this time.

DODGE / CHRYSLER

9. Install the “L” bracket (070066) onto the heat

shield with the provided hardware through the non-

slotted hole in the bracket.

Summary of content (3 pages)

PAGE 1
TM 63-1114 PARTS LIST: DODGE / CHRYSLER A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA Description 2009 Challenger 2008-09 Charger RT 2008-09 300C RT 2008 Magnum RT V8-5.7L HEMI 2008-09 Challenger 2008-09 Charger SRT8 2008-09 300C SRT8 2008 Magnum SRT8 V8-6.1L HEMI TOOLS NEEDED: 4mm allen 3/4” drill bit 10mm socket 13mm socket 10mm wrench drill flat blade screwdriver hack saw ratchet Hose Clamp #56 Silicone Hose 3.50”ID x 2.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Install the two pieces of edge trim onto the heat shield as shown, be sure to leave a gap at the bracket mounting locations. 11. Install the heat shield assembly into the vehicle and secure to the bracket installed in step #8. Then secure the “L” bracket with the factory bolt removed in step #6 to the air box mounting location. 16. Install the provided grommet into the K&N® intake tube as shown. 16a. On SRT 8; 6.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 23. Reconnect the air temperature sensor electrical connection as shown. 2. Test drive the vehicle.