Installation Manual

63-1561
TOOLS NEEDED:
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery
cable erases pre-programmed electronic
memories. Write down all memory settings be-
fore disconnecting the negative battery cable.
Some radios will require an anti-theft code to
be entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
NOTE: This kit was not designed
to t vehicles with a body lift.
2. Release the red locking tab and then disconnect
the inlet air temperature electrical connection.
DODGE
2009-14 Ram 1500
V8-5.7L
2013-14 Ram 2500
V8-5.7L
3. Loosen the hose clamp that secures the intake
tube to the throttle body.
4. Disconnect the crank case vent hose from the air
box.
5. Disconnect the factory intake hose from the
throttle body, then lift up the air box assembly and
remove from the vehicle.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
6. Lift up the engine cover to dislodge it from the
mounting posts and then remove it from the
vehicle.
A
B
A
G
H
C
D
I
I
J
M
L
K
Q
M
M
M
O
S
R
N
O
AC
Q
P
F
AA
E
M
AB
M
U
V
T
W
X
Y
Z
Y
Z
Y
Z
Y
Z
Y
Y
Z
Z
Ratchet
Extension
13mm Socket
10mm Socket
5/16” Socket
10mm Wrench
¾” Wrench
4mm Allen Wrench
Flat Blade Screwdriver
A Hose Clamp #56 2 08620
B Hose; 3-1/2” ID X 2” L 1 08698
C Intake Tube 1 087236
D Grommet; 1”OD,1/2”ID,1/2” Thk. 1 08064
E Cable Ties; 11” Black 1 21590
F Extension Harness; Dodge IAT 1 21681
G Vent; Strt, 5/8 Barbed 1/4 NPT 1 08911
H Hose; 5/8”ID X 14”L, Silicone 1 084083
I Hose Clamp #64 Stainless 2 08645
J Hose; 4” ID X 3” L Hump 1 08418
K Bolt; M6 X 1.00 X 16mm, Bttnhd 2 07730
L Washer; 1/4” Lcok, ZN 2 08198
M Washer; 1/4”ID X 5/8”OD - SAE 8 08275
N Heat Shield 1 073126
O Bolt; 6MM-1.00 X 16mm, SS 3 07812
P Bracket; “Z”, STL, TK/PC 1 083103-1
Q Nut; 6mm Nylock, Hexhead, SS 3 07512
R Adaptor; #454 1 27300
S Bracket; “L”, STL, TK/PC 1 083127
T Edge Trim (55”) 1 102480
U Hosel Clamp #104 1 08697
V Air Filter 1 RF-1044
W Heat Shield A 1 073127
X Heat Shield B 1 073128
Y M5 Washer 8 07724
Z M5 Bolt 8 07740
AA Extension Harness 1 21680
AB Spacer 1 06555
AC Bolt; 6MM-1.00 X 20mm, SS 1 07795
Description Qty. Part # Description Qty. Part # Description Qty. Part #
PARTS LIST: