Installation Manual

63-1564
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery
cable erases pre-programmed electronic
memories. Write down all memory settings be-
fore disconnecting the negative battery cable.
Some radios will require an anti-theft code to
be entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
TOOLS NEEDED:
PARTS LIST:
Description Qty. Part #
2. Lift up and remove the engine cover.
3. Disconnect the inlet air temperature sensor
electrical connection.
4. Disconnect the crank case vent hose from the air
lter housing.
5. Loosen the hose clamp that secures the intake
tube to the throttle body.
6. Remove the bolt that secures the air lter
housing to the core support.
4mm Allen Wrench
10mm Socket
14mm Socket
10mm Wrench
Extension
Ratchet
Flat Blade Screwdriver
DODGE / CHRYSLER
2011-14 Charger
2011-14 Challenger
2011-14 300
V6-3.6L
A Hose Clamp #48 1 08601
B Hose; 3.25” ID TO 3.50” ID X 2.25”L, TPRD, BLK 1 084091
C Hose Clamp #52 1 08610
D Grommet; 1”OD, 1/2”ID, 1/2”THK 1 08064
E Intake Tube (II) 1 087251
F Bolt; 8MM -1.25 X 16MM, Hexhead 1 07844
G Washer; 8MM Spring (Wave) 1 08239
H Washer; 8MM, Flat, SS 1 08272
I Bracket; “L,” 63-1564, STL, TK/PC 1 083154
J Vent; 90DEG, 1/2” Hose, 1/4” NPT, Black, Plastic 1 08110FK
K Hose; 1/2” ID X 14”L 1 08402
L Hose Clamp #56 2 08620
M Hose; 3-1/2” ID X 3”L Hump Molded 1 084057
N Bolt; M6 X 1.00” X 20MM Hex, SS 1 07795
O Bolt; M6-1.00 X 25MM Buttonhead, SS 1 07729
P Washer; 6MM Flat, SS 2 08269
Q Washer, M6 Split Lock Zinc 3 1-3025
R Washer; 1/4” ID X 5/8” OD -SAE 3 08275
S Bracket, 69-2521, “L,” SML, STL, TB/PC 1 070066
T Bolt; M6 X 1.00 X 16MM, Buttonhead, SS 2 07730
U Spacer; .625” OD X .250” ID X .250”L, 1 06555
V Heat Shield 1 074088
W Nut; 6MM Nylock, Hexhead, SS 1 07512
X Edge Trim (20”) 1 102494
Y Bolt; 3/8”-16 X 1-1/4”L SS Hex Head Bolt 1 07779
Z Washer; 3/8” Flat Washer, SS 1 08134
AA Edge Trim (15”) 1 102474
AB Insert; 3/8-16 X 3/400 X 15/16L, Rubber 1 08163
AC Adapter; Universal, 6” Filter 3.5” Coupler 1 21512-1
AD Hose Clamp # 104 1 08697
AE Air Filter 1 RF-1042
A
B
C
D
I
H
G
F
E
J
K
L
M
L
P
N
S
R
Q
O
T
Q
R
P
T
Q
R
W
Y
Z
V
AB
AA
X
AC
AD
AE
U