Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 63-1565 AirCharger Performance Air Intake System

63-1565

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED

HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

DODGE /

CHRYSLER

2012-14 Charger SRT 8

2011-14 Challenger SRT8

2012-14 300C SRT 8

V8-6.4L HEMI

A Hose Clamp #56 1 08620

B Hose; 4”ID to 3.5”ID X 3”L TPRD Reinforced 1 08497

C Hose Clamp # 64 Stainless 3 08645

D Intake Tube 1 087255

E Vent; 90°, 1/2” Hose, 1/4” NPT, Blk., Plastic 1 08110FK

F Hose; 1/2”ID X 12”L 1 087031

G Hose Mender; 1/2” to 5/8”, Barbed 1 08726

H Hose; 5/8” ID X 6”L, Black Silicone 1 08653

I Grommet; 1-1/16 OD, 1/2 ID, 3/8 Thk. 1 080544

J Hose; 4”ID X 3”L Hump Reinforced 1 08418

K Bolt; M6-1.00 X 25mm, SS 1 07858

L Bracket; “L”, Fin., TB/PC 1 070742

M Washer; 6mm Flat, SS 4 08269

N Spacer; .625”OD X .250”ID X .250”L, Aluminum 1 06555

O Bolt; M6 X 1.00 X 16mm, Buttonhead, SS 2 07730

P Washer; M6 Split Lock Zinc 2 1-3025

Q Nut; 6mm Nylock, Hexhead, SS 1 07512

R Heat Shield 1 074098

S Bolt; 3/8” -16 X 1-1/4”L SS Hex Head Bolt 1 07779

T Washer; 3/8” Flat Washer, SS 1 08134

U Insert; 3/8-16 X 3/400 X 15/16L, Rubber 1 08163

V Edge Trim (48”) 1 102485

W Adaptor; # 454 1 27300

X Hose Clamp # 104 1 08697

Y Air Filter 1 RF-1042

2. Disconnect the inlet air temperature air sensor

electrical connection.

3. Lift up and remove the driver side ignition coil

cover as shown.

6. Remove the bolt that secures the air box to the

core support.

5. Loosen the hose clamp securing the intake tube

to the throttle body.

4. Disconnect the crank case vent hose from the

valve cover.

7. Lift up and remove the complete intake track

from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

8. Install the lter adapter into the heat shield and

secure with the provided hardware.

9. Install the provided heat shield mounting bracket

(070742) along with the spacer onto the heat shield

as shown.

4mm Allen Wrench

10mm Socket

14mm Socket

10mm Wrench

Extension

Flat Blade Screwdriver

Ratchet

Summary of content (3 pages)

PAGE 1
63-1565 A DODGE / CHRYSLER B C 2012-14 Charger SRT 8 2011-14 Challenger SRT8 2012-14 300C SRT 8 V8-6.4L HEMI H D G C J C E TOOLS NEEDED: L F I 4mm Allen Wrench 10mm Socket 14mm Socket 10mm Wrench Extension Flat Blade Screwdriver Ratchet K M V O PM R S N P M Q T U PARTS LIST: Description A B C D E F G H I J K L M Hose Clamp #56 Hose; 4”ID to 3.5”ID X 3”L TPRD Reinforced Hose Clamp # 64 Stainless Intake Tube Vent; 90°, 1/2” Hose, 1/4” NPT, Blk.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Install the provided rubber insert onto the heat shield as shown and secure with the provided hardware. 11. Install the provided edge trim onto the heat shield as shown. NOTE: Some trimming of the edge trim will be necessary. 12. Install the provided silicone hump hose (08418) onto the filter adapter and secure with the provided hose clamp. 15. Remove the inlet air temperature sensor from the factory intake tube as shown. 20.
PAGE 3
Continued INSTALLATION INSTRUCTIONS ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 25. Reconnect the vehicle’s negative battery cable.