Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-0021TB Typhoon Air Intake Kit, Complete Cold Air, Blue

69-0021TS

69-0021TB

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED

HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

TO START:

PARTS LIST:

Description Qty. Part #

WARNING: The K&N

Drycharger

included with this kit must be installed on the K&N

air lter when used with this K&N

cold air

intake system. The K&N

cold air intake system a performance product that can be used safely during mild weather conditions. During

harsh and inclement weather conditions, you must convert your cold air intake system to a short ram conguration, or return your

vehicle to the stock OEM airbox and intake tract conguration. Failure to follow these instructions can void your warranty.

8” Extension

8mm Socket

10mm Socket

Flat Blade Screwdriver

Pliers

Ratchet

A Hose Clamp #44, SS 5 08560

B Hose; 2-3/4”ID X 2”L 1 08440

C Hose; 1/2” X 1”L 1 084038

D Intake Tube 1 27169

E Bolt; M6 - 1.00 X 12mm, SS 2 07727

F Nut; 6mm Nylock, SS 2 07512

G Washer; 6mm Wave, SS 4 08277

H Bracket; “L” Long, STL, FB/PC 1 010050

I Stud; Rubber Mount 6mm 2 07027

J Hose; 2-3/4”ID X 3”L Hump Hose 1 08439

K Cold Air Tube 1 27170

L Bracket, “L”, STL, FB/PC 1 010049

M Air Filter 1 RU-4870

N Drycharger

1 RX-4730DK

ACURA

2. Pull rmly upwards to remove the battery cover,

then, disconnect the negative battery cable.

4. Depress the hose clamp and remove the

crankcase vent hard line from the stock intake tube

as shown.

5. Unclip the wire harness from the stock intake

tube as shown.

6. Loosen the hose clamp at the throttle body as

shown.

7. Loosen the four bolts on the air cleaner cover

and pull upwards, then, unclip the wire harness and

remove the cover as shown.

8. Loosen and remove the two bolts that secure the

lower air cleaner assembly as shown.

9. Depress the release tab and remove the wire

harness from the bracket on the lower air cleaner

assembly as shown.

3. Use a at blade screwdriver to remove the air

inlet cover, which is secured by two plastic rivets.

2004-08 TL

V6-3.2L

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

Summary of content (3 pages)

PAGE 1
® 69-0021TS 69-0021TB ACURA 2004-08 TL V6-3.2L TOOLS NEEDED: 8” Extension 8mm Socket 10mm Socket Flat Blade Screwdriver Pliers Ratchet PARTS LIST: A B C D E F G Description Hose Clamp #44, SS Hose; 2-3/4”ID X 2”L Hose; 1/2” X 1”L Intake Tube Bolt; M6 - 1.00 X 12mm, SS Nut; 6mm Nylock, SS Washer; 6mm Wave, SS Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Slide the lower air cleaner assembly off of the air inlet duct and remove the lower air cleaner assembly as shown. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 11. Raise the vehicle up and support it with jack stands, then, remove the front tire as shown. 12. Remove the lower spoiler flap which is secured by two bolts as shown 16.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 37. The C.A.R.B. exemption sticker, (attached), must be visible under the hood, so the emissions inspector can see it when the vehicle is required to be tested for emissions. California requires testing every two years, other states may vary. 28. From underneath the vehicle slide the K&N® cold air intake tube through the hole in the inner fender as shown. 32. Install the K&N® air filter from underneath the vehicle and secure it with the provided hose clamp as shown.