Installation Manual

69-1019TS
TOOLS NEEDED:
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED
HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable. Be sure the engine is completely
cool before beginning the removal of the stock
components. Be sure the vehicle is completely cool
before beginning intake kit installation.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories.
Write down all memory settings before
disconnecting the negative battery cable. Some
radios will require an anti-theft code to be
entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
PARTS LIST:
Description Qty. Part #
®
2. Disconnect the mass air sensor electrical
connection and unhook the wiring harness from the
upper air box.
3. Release the spring clamp securing the crank
case vent tube into the intake tube and then
remove the crank case vent tube from the intake
tube.
4. Loosen the hose clamp securing the intake tube
to the throttle body.
5. Release the two clips securing the upper air box
to the lower air box and then remove the upper air
box and intake tube assembly.
6. Remove the lower air box retaining bolt shown.
3mm Allen Wrench
4mm Allen Wrench
10mm Socket
Extension
Flat Blade Screwdriver
Phillips Screwdriver
Pliers
Ratchet
HONDA / ACURA
2012-14 Civic SI
2013-14 ILX
L4-2.4L
A Hose Clamp #44 Stainless 1 08560
B Hose; 3-1/4” To 2-3/4” ID X 2”L TPRD Reinforced 1 084034
C Hose Clamp #52 2 08610
D Intake Tube 1 27560
E Hose; 1/4” ID X 10-1/2”L Reinforced 1 08400
F Bolt; M4-0.07 8MM, A/H Cap, SS 2 07733
G Vent; 90 DEG, 1/2” Hose, 1/4”NPT, Black, Plastic 1 08110FK
H Venturi; 3.075” OD X 2.975” ID X 3.25”L, Plastic 1 9-0378
I Hose Clamp #56 1 08620
J Hose, Hump 3.25/3.50 X 3.00” 1 5-576
K Hose; 3-1/2” To 3”ID X 3” ID X 3”L TPRD Molded 1 08724
L Hose Clamp #48 1 08601
M Bolt; M6 X 1.00 X 16MM, Buttonhead, SS 2 07730
N Washer, M6 Split Lock Zinc 3 1-3025
O Washer; 6MM Flat, SS 3 08269
P Edge Trim (30”) 1 102489
Q Stud; Rubber Mount, M6 X 1, 1” T, M/F (9376K146) 1 02033
R Bolt; 6MM-1.00 X 16MM, SS 1 07812
S Heat Shield 1 074106
T Hose; 1/2” ID X 12”L 1 087031
U Super Glue, 3G Drip Proof 1 409
V Adapter: Universal, 6” Filter 3.5” Coupler 1 21512-1
W Hose Clamp # 104 1 08697
X Air Filter 1 RU-4600
Y Hose Clamp #64 1 08645
A
B
C
E
F
H
G
C
J
I
M
M
Y
K
L
Q
N
N
O
O
O
N
R
T
U
V
W
X
S
P
D