User Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-1212TS Performance Intake Kit

69-1212TS

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

HONDA

2013-14 Accord

V6-3.5L

TOOLS NEEDED:

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A HOSE CLAMP #44 1 08560

B HOSE; 3.5" TO 2.75" X 2"L 1 084093

C HOSE CLAMP #56 1 08620

D INTAKE TUBE 1 27330TS

E BOLT; M4-0.07 8MM, A/H 2 07733

F VENT; 90 DEG, 1/2: HOSE, 1/4” 1 08110FK

G HOSE; 1/2" ID X 3-1/2"L 1 087028

H BRACKET; "L", 69-1212, STL 1 064302

I WASHER; 6MM ,FLAT,SS 5 08269

J WASHER; M6 SPLIT LOCK ZINC 3 1-3025

K BOLT; M6 X 1.00 X 12MM, SS 1 07727

L CABLE TUES; 11" BLACK 1 21590

M EDGE TRIM (61") 1 102492

N HEAT SHIELD 1 073133

O BOLT; 6MM-1.00 X 16MM, SS 3 07812

P STUD; RUBBER MOUNT, M6 1 02033

Q BRACKET; 63-1025, SMALL 1 070015

R NUT; 6MM NYLOCK, HEXHEAD 1 07512

S HOSE CLAMP #60 1 08624

T AIR FILTER 1 RC-4630XD

PARTS LIST:

Ratchet

Extension

12mm socket

10mm socket

8mm socket,

Flat Blade Screw Driver

Phillips Screw Driver

Pliers

3mm allen key

10mm wrench

2. Disconnect the mass air sensor electrical

connection and unhook the wiring harness from the

air box.

3. Lift o the engine cover.

4. Disconnect the crank case vent tube from the

intake hose.

5. Loosen the hose clamp securing the intake hose

to the throttle body and unhook the wiring harness

from the intake hose.

6. Loosen and remove the two air box mounting

bolts.

NOTE: The front mounting bolt is down low

between the battery and the air box.

B C

NOTE: Excludes LEV2 SULEV 2013-2014

Test Groups: DHNXV03.5VC3, EHNXV03.5SC3

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
® 69-1212TS HONDA 2013-14 Accord V6-3.5L NOTE: Excludes LEV2 SULEV 2013-2014 Test Groups: DHNXV03.5VC3, EHNXV03.5SC3 B A M C D TOOLS NEEDED: N E Ratchet Extension 12mm socket 10mm socket 8mm socket, Flat Blade Screw Driver Phillips Screw Driver Pliers 3mm allen key 10mm wrench Q O J I R I OI G F H J I K L O J I M S T P PARTS LIST: Description Qty. Part # Description Qty. Part # A HOSE CLAMP #44 1 08560 B HOSE; 3.5" TO 2.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Lift up the air box half way out, then unhook the wiring harness from the air box and remove the air box assembly. 8. Install the heat shield mounting bracket (070015) onto the heat shield as shown. NOTE: The longer leg of the bracket should be attached to the heat shield. 9. Cut the provided edge trim into two sections. One section will be 44” and one section will be 14.5” long. 10. Install the 14.5” section of edge trim into the hole of the heat shield as shown.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 22.