Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-2023TS Performance Intake Kit

69-2023

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

™

MINI

2011-13 Cooper S

2011-14 Clubman S

L4 - 1.6L Turbo

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

Description Qty. Part #

A Intake Tube 1 27595TS

B Hose Clamp #44 Stainless 2 08560

C Hose; 2-3/4" ID X 2"L Reinforced 1 08440

D Nut; 6MM Nylock, Hexhead, SS 2 07512

E Washer; 6MM Flat, SS 4 08269

F Heat Shield 1 073130

G Bolt; M6 X 1.00 X 16MM, SS 2 07730

H Hose Clamp #44 1 08577

I Air Filter 1 RU-4960

PARTS LIST:

Ratchet

Extension

10mm socket

7mm socket

screw driver

T27 torx

T25 torx

4mm Allen key

Stock

Mass Air

2. Disconnect the mass air sensor electrical

connection and unhook the vent line from the air

box.

3. Loosen the hose clamp which secures the intake

tube to the mass air sensor.

4. Loosen the three screws securing the upper air

box housing to the lower housing.

5. Remove the upper air box housing and air lter

from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

6. Remove the two screws securing the mass

air sensor to the upper air box housing and then

remove the sensor as shown.

7. Remove the factory O ring from the mass air

sensor.

8. Install the mass air sensor into the K&N

heat

shield using the provided hardware.

NOTE: Be sure to install the button head bolts

from the inside of the heat shield out.

9. Install the K&N

air lter onto the mass air

sensor inside the heat shield and secure with the

provided hose clamp.

NOTE: Drycharger

air lter wrap; part #

RX-4990DK is available to purchase separately.

To learn more about Drycharger

lter wraps or

look up color availability please visit

http://www.knlters.com

Summary of content (2 pages)

PAGE 1
™ 69-2023 TOOLS NEEDED: Ratchet Extension 10mm socket 7mm socket screw driver T27 torx T25 torx 4mm Allen key MINI 2011-13 Cooper S 2011-14 Clubman S L4 - 1.6L Turbo F Stock Mass Air E D B PARTS LIST: C A E D G I Description Qty. Part # A Intake Tube 1 27595TS B Hose Clamp #44 Stainless 2 08560 C Hose; 2-3/4" ID X 2"L Reinforced 1 08440 D Nut; 6MM Nylock, Hexhead, SS 2 07512 E Washer; 6MM Flat, SS 4 08269 F Heat Shield 1 073130 G Bolt; M6 X 1.
PAGE 2
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 10.