Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-2547TS Performance Intake Kit

69-2547

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

™

DODGE

2013-14 Dart

L4-2.0L

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

Description Qty. Part #

A Hose Clamp #44 Stainless 2 08560

B Hose, 3" ID X 3"L Hump 1 08696

C Intake Tube 1 27594TS

D Bracket; Z, 69-2547, STL, TB/PC 1 064301

E Bolt; 6MM-1.00 X 16MM, SS 4 07812

F Washer; M6 Split Lock Zinc 4 1-3025

G Washer; 6Mm Flat, SS 4 08269

H Hose Clamp #52 1 08610

I Vent; STRT 1/2" Hose, 1/4:NPT 1 080022

J Hose; 1/2" ID X 9"L 1 08401

K Edge Trim (30") 1 102489

L Air Filter 1 RU-4990

M Standoff; 6.0 Ford Air box 2 06532

N Washer; 5/16" ID X 5/8"OD, Flat 2 08276

O Washer, M8 Split Lock Zinc 2 1-3036

P Bolt; 8MM-1.25 X 16MM 2 07844

Q Bracket; 57-301, L-Bend, FIN 2 070812

R Heat Shield 1 073129

S Bracket; 57-1528, SM. Twist, Mild 1 07139

PARTS LIST:

Ratchet

Extension

13mm socket

10mm socket

7mm socket

10mm wrench

Flat blade screw driver

2. Loosen the hose clamp securing the intake hose

to the intake plenum.

3. Disconnect the crank case vent hose from the air

lter housing

4. Remove the bolt securing the air lter housing

onto the core support and unhook the coolant line

from the air box.

NOTE: This bolt will be reused in a later step.

5. Lift up and remove the air lter housing

assembly from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

6. Disconnect the inlet air temperature sensor

electrical connection and then loosen the hose

clamp securing the intake plenum to the throttle

body.

7. Lift up and remove the intake plenum from the

vehicle.

8. Remove the crank case vent hose from the valve

cover port.

9. Install the provided shorter crank case vent

hose.

10. Reinstall the intake plenum and reconnect the

inlet air temperature electrical connection, secure

the plenum with the factory hose clamp.

11. Install the provided edge trim onto the heat

shield as shown.

NOTE: Some trimming of the edge trim will be

necessary.

Summary of content (2 pages)

PAGE 1
™ 69-2547 PARTS LIST: Description DODGE 2013-14 Dart L4-2.0L A B K A C H L G F TOOLS NEEDED: Ratchet Extension 13mm socket 10mm socket 7mm socket 10mm wrench Flat blade screw driver D G F E R E I J G E F S P P O N O N Q GF E Q M Qty. Part # A Hose Clamp #44 Stainless 2 08560 B Hose, 3" ID X 3"L Hump 1 08696 C Intake Tube 1 27594TS D Bracket; Z, 69-2547, STL, TB/PC 1 064301 E Bolt; 6MM-1.
PAGE 2
INSTALLATION INSTRUCTIONS Continued 12. Install one of the provided brackets #070812 onto the heat shield as shown using the provided hardware. 13. Flip the heat shield over and install the remaining bracket #070812 and secure with the provided hardware. 14. Install the two heat shield mounts onto the brackets as shown. 17. Install the tube mounting bracket #064301 onto the engine mount and secure with the factory bolt from the previous step.