Installation Manual

A
B
C
D
E
C
F
G
H
K
Mass Air
Factory
P
P
N
N
N
O
O
Q
Q
M
O
T
M
L
I
J
R
O
O
M
S
S
N
J
M
N
O
M
N
O
J
O
O
N
U
W
V
Q
S
Y
Z
X
X
M
N
O
69-3517
TOOLS NEEDED:
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED
HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories.
Write down all memory settings before
disconnecting the negative battery cable. Some
radios will require an anti-theft code to be
entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
™
FORD
2012-14 Focus
L4-2.0L
2. Release the red locking tab and then disconnect
the mass air sensor electrical connection. Also
unhook the mass air sensor wiring harness clip
from the mass air sensor.
3. Depress the blue locking tab and then
disconnect the EVAP vent line.
4. Disconnect the crank case vent line from the
intake tube.
5. Disconnect the crank case vent hose from the
valve cover and then remove the vent hose from
the vehicle.
6. Loosen the hose clamp securing the intake tube
to the throttle body.
7. Release the rubber strap securing the fresh air
intake scoop to the duct.
8. Lift up the air box assembly to release it from the
mounting grommets; remove the air box from the
vehicle.
9. Remove the rubber fresh air duct from the
vehicle.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
4mm Allen Wrench
8mm Socket
10mm Socket
Extension
Flat Blade Screwdriver
Ratchet
Description Qty. Part #
A Hose Clamp #40 1 08554
B Hose; 2-3/4” To 2-1/2”ID 1 084016
C Hose Clamp #44 Stainless 2 08560
D Grommet; 1”OD, 1/2”ID, 1/2” Thk. 1 08064
E Tube; 2.75”OD X 5.5”L 1 27543
F Vent; 90°, 1/2”Hose, 1/4”NPT 1 08110FK
G Hose; 1/2” X 24”L 1 08642
H Hose; 3” To 2-3/4” X 3”L Hump 1 08421
I Grommet; .875ODX.50ID 1 08063
J Edge Trim (55”) 1 102480
K Hose Clamp #48 1 08601
L Heat Shield; Fresh Air, Mild STL 1 074100
M Bolt; M6 X 1.00 X 16mm, SS 6 07730
N Washer; M6 Split Lock Zinc 9 1-3025
O Washer; 6mm Flat, SS 12 08269
P Bolt; M6-1.00 X 25mm SS 2 07729
Q Stud; Rubber MNT, M/F, 1/2”L 3 070228
R Heat Shield; Side, Mild STL, 1 074101
S Nut; 6mm Nylock, Hexhead, SS 3 07512
T Bolt; HEX M6-1 X 35mm 1 1-2002
U Bracket; “C”, STL TB/PC 1 083161
V Washer; 1”D X 1/4 Hole Fender 1 08160
W Heat Shield; Mild STL, TB/PC 1 074102
X Nipple; Heat Shield Mount 2 8-186
Y Hose Clamp # 44 1 08577
Z Air Filter 1 RC-5284
PARTS LIST: