Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N Performance Cold Air Intake Kit 69-4521TS with Lifetime Filter for Chevrolet Cruze 1.4L

69-4521

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED

HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

™

CHEVROLET

2011-14 Cruze

L4-1.4L Turbo

2. Release the locking tab and then disconnect the

mass air sensor electrical connection.

3. Disconnect the airbox drain tube from the airbox.

NOTE: The drain tube will pull straight out from

the airbox.

4. Loosen the hose clamp securing the stock intake

tube to the intake elbow.

5. Lift the airbox assembly to dislodge it from the

mounting grommets and then remove the airbox

from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

6. Unhook the two clips that secure the airbox drain

tube to the inner fender, and then remove the drain

tube from the vehicle.

7. Remove the front motor mount bolt shown.

NOTE: This bolt will be reused in a later step.

8. Install the provided rubber mounted studs onto

the heat shield mounting bracket as shown.

9. Install the heat shield mounting bracket onto

the motor mount and secure with the factory bolt

removed in step #7.

NOTE: Do not completely tighten at this time.

Flat blade Screwdriver

Phillips Screwdriver

Ratchet

Extension

7mm Socket

10mm Socket

15mm Socket

2.5mm Allen

Pliers

A Nut; 6MM Nylock, Hexhead, SS 6 07512

B Washer; 6MM Flat, SS 8 08269

C Intake Tube 1 27488

D Screw; M4- .7 X 12, Button Head SS 2 07726

E Gasket; 63-1034, 1/16” Neoprene 2 09202

F Washer, M6 Split Lock Zinc 2 1-3025

G Bolt; 6MM-1.00 X 16MM, SS 2 07812

H Edge Trim (39”) 1 102496

I Heat Shield 1 074086

J Stud; Rubber MNT, M/F, 1/2”L 2 070228

K Bracket; “L”, 69-4521, STL, TK/PC 1 083149

L Stud, 6M-1 X 30 DBL Ended 4 1-107

M Adaptor; 57-2535 #350 1 21510

N Hose Clamp #80 1 08694

O Air Filter 1 RU-5147

Summary of content (2 pages)

PAGE 1
™ 69-4521 CHEVROLET H 2011-14 Cruze L4-1.4L Turbo D C B A B A E I B TOOLS NEEDED: B Flat blade Screwdriver Phillips Screwdriver Ratchet Extension 7mm Socket 10mm Socket 15mm Socket 2.5mm Allen Pliers M O E N L A L L F B B L G J F K PARTS LIST: Description A B C D E Nut; 6MM Nylock, Hexhead, SS Washer; 6MM Flat, SS Intake Tube Screw; M4- .7 X 12, Button Head SS Gasket; 63-1034, 1/16” Neoprene Qty.
PAGE 2
INSTALLATION INSTRUCTIONS Continued 10. Remove the two screws that secure the mass air sensor to the factory airbox and then remove the mass air sensor from the airbox. 15. Loosen the hose clamp securing the intake elbow to the throttle body so that the intake elbow position can be adjusted. 11. Install the mass air sensor into the K&N® intake tube and secure with the provided hardware. 16.