Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-5304TS Performance Intake Kit

69-5304

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

™

HYUNDAI

2012-14 Veloster

L4-1.6L

2. Loosen the hose clamp securing the intake tube

to the throttle body.

3. Disconnect the crank case vent hose from the

factory intake tube.

4. Remove the three bolts securing the factory air

box assembly onto the inner fender.

5. Remove the air box assembly from the vehicle.

NOTE: K&N Engineering, Inc., recommends

that customers do not discard factory air

intake.

6. Push in the center of the fresh air duct retaining

clips and then remove the clips.

TOOLS NEEDED:

Ratchet

Extension

Flat blade screw driver

10mm socket

4mm Allen wrench

2.5mm Allen wrench

9/16” wrench

Pliers

Description Qty. Part #

A Hose Clamp #40 1 08554

B Hose, Hump 2.50/3.00 X 3.00” 1 5-574

C Hose Clamp # 48 1 08601

D Intake Tube 1 27574TS

E Vent; STRT, 3/8”Hose, 1/4”NPT, Plas 1 08047

F Hose Clamp #52 1 08610

G Hose, Hump 3.25/3.50 X 3.00 1 5-576

H Hose Clamp #56 1 08620

I Bolt; 6MM-1.00 X 16MM, SS 4 07812

J Washer; M6 Split Lock Zinc 6 1-3025

K Washer; 1/4”ID X 5/8”OD, SAE 6 08275

Description Qty. Part #

L Edge Trim (30”) 1 102489

M Bolt; M6 X 1.00 X 16MM, Buttonhead, SS 2 07730

N Bolt; M4 X .7 X 8MM, Buttonhead, SS 1 07741

O Washer; 4MM Flat 1 08278

P Heat Shield Scoop 1 07388

Q Heat Shield 1 07389

R Stud; Rubber MNT, M/F, 1/2”L X 1”W, M6 X 1.00 1 070228

S Stud;Rubber Mount, M6 X 1, 1” T, M/F 1 02033

T Adapter; universal, 6” Filter 3.5” Coupler 1 21512-1

U Hose Clamp # 104 1 08697

V Air Filter 1 RU-4600

W Hose Clamp #6 1 08407

PARTS LIST:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

Summary of content (3 pages)

PAGE 1
™ 69-5304 HYUNDAI 2012-14 Veloster L4-1.6L A D L M TOOLS NEEDED: B J Ratchet Extension Flat blade screw driver 10mm socket 4mm Allen wrench 2.5mm Allen wrench 9/16” wrench Pliers C K N O F E P KJ W G I H Q T U L V I J K I J K R S PARTS LIST: Description Qty. Part # Description Qty. Part # A Hose Clamp #40 1 08554 L Edge Trim (30”) 1 102489 B Hose, Hump 2.50/3.00 X 3.00” 1 5-574 M Bolt; M6 X 1.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Remove the fresh air intake duct. 8. Cut the provided edge trim into two sections, one section will be 20” long and the shorter section will be 8” long. 9. Install the 8” section onto the K&N® fresh air intake scoop as shown. 10. Install the 20” section onto the heat shield as shown. 12. Install the ½” rubber mounted stud into the front factory air box mounting location as shown. 13.
PAGE 3
Continued INSTALLATION INSTRUCTIONS ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 22.