Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N Performance Cold Air Intake Kit 69-5312TS with Lifetime Filter for Hyundai Veloster Turbo 1.6L

69-5312

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

™

HYUNDAI

2013-14 Veloster

L4-1.6L turbo

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A Hose Clamp #48 1 08601

B Hose; 3" To 2-3/4"ID X 3"L TPRD 1 08096

C Hose Clamp #40 1 08554

D Vent; STRT 1/2" Hose, 1/4"NPT 1 080022

E Intake Tube 1 27333TS

F Bracket, 69-5312, STL, TB/PC 1 064303

G Washer, 6MM, Flat,SS 7 08269

H Washer; M6 Split Lock, Zinc 6 1-3025

I Bolt; M6 X 1.00 X 12MM, SS 4 07727

J Hose Clamp # 16 2 08413

K Vent; STRT, 1" X 1" Barbed 1 08296

L Hose; 1"ID X 11"L W/1"L 90DEG 1 08479

M Edge Trim (66") 1 102472

N Heat Shield 1 073136

O Bracket; 63-1025, Small, TB/PC 1 070015

P Bolt; 6MM -1.00 X 6MM, SS 3 07812

Q Heat Shield Lid 1 073137

R Nut; 6MM Nylock, Hexhead, SS 1 07512

S Washer; 1"D X 1/4 Hole Fender 1 08160

T Washer; 1" X .300 X .100 Rubber 1 21685

U Hose Clamp #52 1 08610

V Air Filter 1 RU-4990

PARTS LIST:

Ratchet

Extension

10mm Socket

8mm Socket

Screw Driver

Pliers

2. Lift up and remove the engine cover from the

engine.

3. Loosen the hose clamp securing the intake

hose to the air box and release the spring clamp

securing the air injection hose and then disconnect

the air injection hose.

4. Release the spring clamp securing the crank

case vent hose and then disconnect the crank case

vent hose. Loosen the hose clamp securing the

intake hose to the turbo inlet and then disconnect

and remove the intake hose from the vehicle.

5. Push the centers of the retaining pins down to

release the fresh air intake scoop.

6. Pull the fresh air intake scoop straight up and out

of the vehicle.

Summary of content (3 pages)

PAGE 1
™ 69-5312 Q HYUNDAI E 2013-14 Veloster L4-1.6L turbo TOOLS NEEDED: Ratchet Extension 10mm Socket 8mm Socket Screw Driver Pliers I D I H G G M C B H I A F J H G P PG G M G I H G U R O L P H J K V M S T N PARTS LIST: Description Qty. Part # Description Qty. Part # A Hose Clamp #48 1 08601 B Hose; 3" To 2-3/4"ID X 3"L TPRD 1 C Hose Clamp #40 1 D Vent; STRT 1/2" Hose, 1/4"NPT E F G Description Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Remove the three bolts securing the air filter housing assembly and then lift up and remove the air filter housing assembly from the vehicle. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 8. Remove the small cover that is installed onto the hose clamp screw securing the intercooler charge hose, then loosen the hose clamp and disconnect the charge hose from the throttle body inlet.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 22. Connect the 90° air injection hose to the factory injection hose as shown and secure with the provided hose clamp. 26. Install the 21”long section of edge trim onto the heat shield cover as shown. 29. Reconnect the vehicle’s negative battery cable. Double check to make sure everything is tight and properly positioned before starting the vehicle. 30.