Installation Manual

ManualsBrandsK&N ManualsAir IntakeK&N 69-8613TS Typhoon Silver Air Intake System

69-8613

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

™

7. Disconnect the crank case vent hose from the

valve cover. Loosen the spring clamp that secures

the intake tube to the throttle body and remove the

stock intake tube from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

SCION / TOYOTA

2008-14 XB

L4-2.4L

2009-13 Matrix

L4-2.4L

2. Remove the two nuts that secure the engine

cover, then remove the engine cover from the

engine as shown.

Flat Blade Screwdriver

Phillips Screwdriver

Ratchet

Extension

14mm Socket

10mm Socket

10mm Wrench

3mm Allen Wrench

Pliers

A Hose Clamp #44 1 08577

B Hose; 3"ID TO 2-1/2"ID TPRD 1 08713

C Hose Clamp #48 2 08601

D Intake Tube 1 27536

E Hose; 5/8"IDx13"L 1 08602

F Bolt; M4-0.07 8mm, A/H Cap 2 07733

G Bolt; 6mm-1.00x16mm, SS 4 07812

H Washer; 1/4" Lock, ZN 4 08198

I Washer; 1/4"IDx5/8"OD - SAE 4 08275

J Bracket; Small 1 070015

K Bolt; M5 - 0.8x12mm B/H, SS 1 07734

L Washer; 5mm Flat, SS 1 08212

M Bracket; "L", STL, FB/PC 1 06509

N Edge Trim (17") 1 102469

O Edge Trim (39") 1 102496

P Heat Shield 1 07360-1

Q Air Filter 1 RU-3570

3. Depress the locking tab on the mass air sensor

electrical connection, then disconnect the mass air

sensor electrical connector.

4. Un-hook the EVAP solenoid valve from the stock

intake tube as shown.

5. Loosen the hose clamp that secures the intake

tube to the upper air box. Then, un-hook the three

upper air box retaining clips. Remove the upper air

box from the vehicle as shown.

6. Remove the three bolts that secure the lower air

box. Then, un-clip the wiring harness and remove

the lower air box from the vehicle.

8. Un-hook the EVAP wiring harness from the

EVAP mounting bracket as shown.

9. Remove the screw that secures the EVAP

mounting bracket, then remove the bracket as

shown.

Summary of content (2 pages)

PAGE 1
™ 69-8613 F SCION / TOYOTA D 2008-14 XB L4-2.4L 2009-13 Matrix L4-2.4L N TOOLS NEEDED: Flat Blade Screwdriver Phillips Screwdriver Ratchet Extension 14mm Socket 10mm Socket 10mm Wrench 3mm Allen Wrench Pliers C G G O H H I I E P J M B K L C Q I H A G PARTS LIST: Description A B C D E F Hose Clamp #44 Hose; 3"ID TO 2-1/2"ID TPRD Hose Clamp #48 Intake Tube Hose; 5/8"IDx13"L Bolt; M4-0.07 8mm, A/H Cap Qty.
PAGE 2
INSTALLATION INSTRUCTIONS Continued 10. Remove the fuel rail mounting bolt shown. NOTE: This bolt will be re-used. 11. Install the tube mounting bracket (#06509) onto the cylinder head using the bolt removed in the previous step. 16. Install the heat shield assembly and secure with the provided hardware. NOTE: The fresh air supply tube is to be installed into the heat shield. 17. Remove the two screws that secure the mass air sensor to the stock air box. Then, remove the mass air sensor as shown. 22.