Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-9505T Typhoon Performance Intake Kit for '09-'10 Audi A4 2.0L L4

69-9505

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

™

AUDI

2009-13 A4

L4-2.0L

2. Remove the four screws which secure the front

core support cover.

NOTE: These screws will be reused in a later

step.

Ratchet

Extension

10mm Socket

7mm Socket

Flat Blade Screwdriver

Pliers

T27 Torx

T25 Torx

4mm Allen Wrench

3mm Allen Wrench

3. Pull up the rear of the cover then push towards

the rear to unhook it from the grill. Then remove the

cover from the vehicle.

4. Remove the two screws which secure the fresh

air scoop to the core support.

NOTE: These screws will be reused in a later

step.

5. Unsnap the fresh air scoop from the air box and

then remove the scoop from the vehicle.

6. Disconnect the mass air sensor electrical

connection.

Stock

Mass Air

A Hose Clamp #36 1 08530

B Hose; 2.375”ID X 3.125”ID, 1 08490

C Hose Clamp #48 2 08601

D Nut; 6MM Nylock, Hexhead 4 07512

E Washer; 1/4”IDx5/8”OD-SAE 9 08275

F Heat Shield Scoop 1 074071

G Bolt; M5 - 0.8 X 12MM B/H, SS 2 07734

H Washer; 5MM Internal Star Cut 2 07724

I Washer; 5MM Flat, SS 2 08212

J Heat Shield 1 074070

K Bolt; M6 X 1.00 X 16MM , Bttnhd 4 07730

L Bolt; M6-1.00 X 25MM, SS 1 07858

M Washer; 3/8” Flat SS 1 08134

N Insert; 3/8-16x3/400x15/16L 1 08163

O Washer; 1/4” Lock, ZN 1 08198

P Bolt; 3/8”-16x1-1/4”L SS 1 07779

Q Bracket; “L”, STL, TK/PC 1 083139

R Edge trim (48”) 1 102490

S Air Filter 1 RF-1047

Summary of content (3 pages)

PAGE 1
™ 69-9505 AUDI G 2009-13 A4 L4-2.0L H I R TOOLS NEEDED: F Ratchet Extension 10mm Socket 7mm Socket Flat Blade Screwdriver Pliers T27 Torx T25 Torx 4mm Allen Wrench 3mm Allen Wrench J E D E K B C S C I G P M N Stock Mass Air H E K E A D D L E O E Q PARTS LIST: A B C D E F G Description Hose Clamp #36 Hose; 2.375”ID X 3.125”ID, Hose Clamp #48 Nut; 6MM Nylock, Hexhead Washer; 1/4”IDx5/8”OD-SAE Heat Shield Scoop Bolt; M5 - 0.8 X 12MM B/H, SS Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Loosen the two hose clamps which secure the stock intake tube to the turbo inlet and factory air box, then remove the intake tube from the vehicle. 8. Pull up the air box and remove it from the vehicle. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 13.Cut the provided edge trim into the four separate lengths as shown.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 25. Reinstall the factory fresh air scoop onto the core support as shown using the factory hardware. 27.